GSM/CDMA/WCDMA/4G(LTE) MOIP Gateway 2 Equipment Information 2.1 Product Brief YX series MOIP Gateway is a multi-functional and high performance product, which is designed with advanced embedded technology. YX series is able to process traditional SMS service and internet data service.
SMS protocol: SMPP3.4 , HTTP API Port Inter-Calling SMS Prefix Setting USSD Send (Auto/Manual) Auto Balance check(need set by USSD/SMS) SIM card Number check (need set by USSD/SMS) Web Browser: Firefox/Chrome /IE/Opera ~ 7 ~ YX Technical department...
3.1 Network Setup Network is a prerequisite to install MOIP Gateway. The following figure shows the topology of Network with a MOIP Gateway connected.(No LAN port) IP Network Switch/Router ~ 9 ~ YX Technical department...
URL: http://GATEWAY_IP/, while GATEWAY_IP is the WAN IP address of the MOIP Gateway, such as 192.168.1.10. As an example, the following introduction will base on the MOIP Gateway with WAN IP 192.168.1.10. ~ 10 ~ YX Technical department...
GSM/CDMA/WCDMA/4G(LTE) MOIP Gateway 4.1 Login First, connect a computer to the same LAN with MOIP, add the MOIP IP segment in the computer. If your computer's IP address is not 192.168.1. XXX, how to change: ~ 11 ~ YX Technical department...
Page 12
The default login account and password are: Account root Password root It is recommended to use IE/FireFox/Chrome to access the web pages. After successfully logged in, the main page to set Gateway is as following: ~ 12 ~ YX Technical department...
DHCP server. PPPoE: In this mode,you can use MOIP device to dail-up network. You can set User Name and Password which you get from your ISP. And you also can set MTU and Service Name. ~ 13 ~ YX Technical department...
Port 1 to 4/8/16/32/64 relate to the physical port of MOIP Gateway. The following table shows the relationship between LED color and port status.( When registering a card, the description of the card may not be displayed in real time. Please refer to the information displayed on the icon) ~ 14 ~ YX Technical department...
The screenshot below shows the SIP and Module status. The status columns are specified as following: Port No: The physical port sequence from 1 to 4/8/16/32/64. Registration Status: Shows the port registration to SIP server infomation status. ~ 15 ~ YX Technical department...
GSM/CDMA/WCDMA/4G(LTE) MOIP Gateway Module Status: Shows the port Module use status(Yes/No). If NO is displayed,please try restarting. If still, Please contact YX NOC IMEI: Specify the port current using of IMEI. 6.3 System Status The screenshot below shows the system status. It includes WAN status, LAN(please ignore) and others.
Here Statistics SMS send and receive, send failure and success of the situation 6.7 InterCall Statistics The status columns are specified as following: Port No: The physical port sequence from 1 to 8/16/32/64. State: Specify the call status. ~ 17 ~ YX Technical department...
For example, if field Web Port is set to 8080 and wan IP is 192.168.1.10, the web pages then should be accessed through URL: http://192.168.1.10:8080 from this computer. The field Telnet Port is used to change the default port of telnet service. ~ 18 ~ YX Technical department...
GSM Call AutoAnswer: Specify whether need to auto-answer the call which is from GSM. If set to Enable, AutoAnswer Time can be used to specify the delay to automatically answer the incoming GSM call. ~ 19 ~ YX Technical department...
Time Interval: Query balance regularly. Manually Call: Manually input a number, let the sim card mark a call 7.3.2 Base Station The screenshot below shows the operation mode to set Basic Settings of Port settings ~ 20 ~ YX Technical department...
Hot-line: Specify a sip phone on the softswitch to pick up the incoming calls Unconditional Forward/ No Answer Forward Number/ Busy Forward: These parameters are designed to be used with a third party system. ~ 21 ~ YX Technical department...
White List: Specify the white list of base station, can be multiple, use a comma. Black List: Specify the black list of the base station, can be multiple, use a comma. Operations: When click the refresh button will change a new base station. ~ 22 ~ YX Technical department...
If a card on a port is assigned with a group of IMEIs, it will randomly use any of the IMEI in group to communicate with mobile base. ~ 23 ~ YX Technical department...
Page 24
Click button Submit on the right to save the old data record. Delete Click Delete on the right of each record to delete the current record. A message box will be popped for delete confirmation. ~ 24 ~ YX Technical department...
Note: the manipulation is executed after pattern is matched. IP-->GSM Callee Prefix: Specify the callee prefix. Digits Stripped: Specify the digits which are stripped. Digits Added: Specify the digits which are added. ~ 25 ~ YX Technical department...
PIN: Specify the PIN for card A/B/C/D/(more) of the port 7.7.2 Billing Setting The screenshot below shows the operation mode to set MOIP billing. A smart billing server for mobile port is embedded in MOIP Gateway. ~ 26 ~ YX Technical department...
Page 27
1 minute) Invalid Balances: Balance after calibration, the implementation of automatic calculation of the balance again, when less than the invalid value will lock, and prompts you(Usually set the balance of 1 minute) ~ 27 ~ YX Technical department...
Invalid SIM keywords: If the device recognizes this keywords from USSD/SMS, it will lock the SIM card and prompt blocked by operator 7.7.4 Tariff List The screenshot below shows the operation mode to set billing tariff. ~ 28 ~ YX Technical department...
The screenshot below shows the operation mode to send USSD through the MOIP Gateway. 7.8.1 USSD Auto Send Here set USSD can be automatically sent as needed(For example, you can customize a preferential voice package by automatic USSD) ~ 29 ~ YX Technical department...
USSD Command: The value of the USSD Port: Select tick to need send USSD ports Response: Show respond to the content of the carrier Send: Press this button, will start sending USSD ~ 30 ~ YX Technical department...
Drop Call: Enabled, the online time to meet the conditions, immediately hang up. Not enabled, it will wait for this call done. Locking Duration: Here to set the card slot lock time, fill -1 means always locked that when you manually replace the SIM card will reset ~ 31 ~ YX Technical department...
Failed SMS Count: The card in use takes effect when the cumulative number of SMS failures has reached this value Other : Please refer to 7.11.4 for instructions 7.9.5 Consecutive Failed SMS Count Checking ~ 32 ~ YX Technical department...
Use Local Policy: When enabled, the settings for MOIP Automation will take effect, and the Automation settings will be obtained from SIMServer when disabled Signal Transport: When UDP is unstable, you can try TCP ~ 33 ~ YX Technical department...
The screenshot below shows the operation mode to set conditions settings of port inter-calling. Fields are specified as following: By Device Online Time: Gateway will start port inter calling by the device online time, and the time between min interval and max interval. ~ 34 ~ YX Technical department...
Number B: Specify the number for card B of the port Number C: Specify the number for card C of the port Number D: Specify the number for card D of the port Number More.. ~ 35 ~ YX Technical department...
7.13 Auto Recharge This item is used to configure automatic recharge settings, which need to be used with automatic recharge server(If you have server, please contact YX NOC install auto recharge software) 7.14 Status Notification This item is used to configure status notification settings that allow the device to submit status to the URL you set.
APN Setting: Please enter the APN you want to define in different carrier codes 8 SMS Setting 8.1 SMS Setting 8.1.1 SMS Receive The screenshot below shows the operation mode to receive sms. ~ 37 ~ YX Technical department...
Page 38
Content: Specify the sms content. Back: Back to the SMS content web page. Refresh: Refresh the web page. Clear: Clear the sms. Reply: Reply the sms Delete: Delete the corresponding sms. ~ 38 ~ YX Technical department...
URL: Specify the sms server URL. Username: Specify the username. Password: Specify the password. Sender: Specify the sender. Receiver: Specify the receiver. Device Port: Specify the device port. ~ 39 ~ YX Technical department...
Page 40
By Consecutive Calls:Gateway will start sms sending by consecutive calls. By Call Duration:Gateway will start sms sending by call duration. The screenshot below shows the operation mode to send SMS through the MOIP Gateway. ~ 40 ~ YX Technical department...
Field Successful SMS Number records down the total number of SMS which is successfully sent out. Field Failed SMS Number records down the total number of SMS which is sent failed. 8.2 SMS Ctrl Setting ~ 41 ~ YX Technical department...
SMS Statistics: Here will be Statistics all ports to send SMS data situation(Reset button to reset the sending status of this card) This data will be stored in the sim card 8.3 SMPP Setting ~ 42 ~ YX Technical department...
Server Address: IMFS/EIMS SMS Server IP (Please get it from your SMS business partner company) User Name: Register account (Please get it from your SMS business partner company) Password: Register password (Please get it from your SMS business partner company) ~ 43 ~ YX Technical department...
SIM card. This setting is used to limit the prefix of the number when running the network SMS business to ensure that the number number conforms to the sending rule of the SIM card. ~ 44 ~ YX Technical department...
IP Address: Specify the ip address. Packet Size: Specify the packet size. Last Time: Specify the ping duration. Package Loss Rate: Specify the package loss rate. The screenshot below shows the manual ping settings ~ 45 ~ YX Technical department...
This item is used to set the device needs to record the log and save the relevant information can be used for engineering personnel to maintain and check the equipment status, please ignore in the normal use. ~ 46 ~ YX Technical department...
GSM/CDMA/WCDMA/4G(LTE) MOIP Gateway 9.4 File Management This is used to export and view log files, please ignore in the normal use ~ 47 ~ YX Technical department...
Another shortcut button is also provided on the top right of Data List to delete multiple selected records in batch. A message box will be popped for confirmation of batch delete. ~ 48 ~ YX Technical department...
Bangladesh is UTC+6, and change as +6. If your device is not touch with the internet and want to get accurate time, the time server will help. 9.5.4 Remote Mangement The screenshot below shows the operation mode for remote management. ~ 49 ~ YX Technical department...
Network must be available for the gateway to communicate with ERM Server, When the registration is complete, you can access your device from the ERM server at any time/address. YX ERM Server(You can register directly through the registration button to register and follow the prompts to use) domain name: MOIP.yx19999.com...
Role Home: The default home page is displayed Permit: The list of permissions this role can use 9.7 Update/ backup & Restore The screenshot below shows the operation mode for system update/restore. ~ 51 ~ YX Technical department...
System restore is used to restore the system to default settings. A message box will be popped for the confirmation of restore. Firmware Version Down(Or Contact Your Account Manager) YX Series MOIP/SIMBANK Lastest Firmware Version 9.8 Save & Reboot Generally, any modification should require the reboot of MOIP Gateway to bring the modification into effect.
Need help?
Do you have a question about the MOIP Series and is the answer not in the manual?
Questions and answers