Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Orbit Fitness OAF300
Summary of Contents for Orbit Fitness OAF300
- Page 1 OAF300 OAF300 AIR BIKE OAF300 350 lbs/160 kgs.
-
Page 2: Before You Begin
. We take great pride in producing this quality product and hope it will provide many hours of quality Although Orbit Fitness constructs its products exercise to make you feel better, look with the finest materials and uses the highest better, and enjoy life to its fullest. -
Page 3: Hardware Identification Chart
HARDWARE IDENTIFICATION CHART This chart is provided to help identify the fasteners used in the assembly process. Place the washers or the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to check the length of the bolts and screws. - Page 4 ASSEMBLY INSTRUCTIONS Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all packing materials from your area and place them back into the box. Do not dispose of the packing materials until assembly is completed.
- Page 5 ASSEMBLY INSTRUCTIONS STEP 3 Slide the RIGHT HANDLEBAR(58) onto the shaft on the MAIN FRAME(1), then secure by screwing the FOOTREST(83) onto the shaft. Refer to the inset drawing. Use the customized wrench to securely tighten the FOOTREST(83). Press one DECORATIVE PLUG(84) into the end of the FOOTREST(83). STEP 4 Attach the LINKAGE(26) to the lower end of the RIGHT HANDLEBAR(58) with the FIXING PLATE(74), DISC SPACER(75), FLAT SOCKET BOLT(M8x1.25x30mm)(105), and NYLOCK NUT(M8x1.25)(93).
- Page 6 ASSEMBLY INSTRUCTIONS STEP 6 NOTE: The RIGHT PEDAL(39) has an R stamped on the end of the pedal shaft. The RIGHT PEDAL (39) has right hand threads and is tightened by turning clockwise. The LEFT PEDAL(34) has an L stamped on the end of the pedal shaft. The LEFT PEDAL(38) has left hand threads and is tightened by turning counterclockwise.
- Page 7 ASSEMBLY INSTRUCTIONS STEP 8 Install two AA batteries into the COMPUTER(85), the batteries are included. Plug the CONNECTION WIRE(63) to the COMPUTER(85). Place the COMPUTER(85) onto the COMPUTER SUPPORT(48) and secure with ROUND HEAD SCREWS (M5x0.8x12mm)(106). NOTE: Be careful not to damage the wires when attaching the COMPUTER(85). STEP 9 Press the WATER BOTTLE HOLDER(113) into the hole in the COMPUTER SUPPORT(48).
-
Page 8: Setup Instructions
SET UP INSTRUCTIONS Place the in the area where it will be used. It is recommended that the be placed on an equipment mat. is approximately 50.1 inches long (max.) x 24.8 inches wide x 50.7 inches tall. An area 4 feet wide x 6 feet long is required for safe operation of the . -
Page 9: Operational Instructions
OPERATIONAL INSTRUCTIONS SEAT HEIGHT ADJUSTMENT center the foot bow on the pedal in the down position. Your leg should be slightly bent and relaxed as shown. If your leg is too straight or your foot cannot touch the pedal, you will need to lower the seat. If your leg is bent too much you will need to raise the seat. -
Page 10: Computer Instructions
COMPUTER INSTRUCTIONS Your Air Bike utilizes an air fan system to create resistance for your workout. We recommend that you use this computer console to vary your workout from session to tness goals. When used regularly in this way, the computer console can become an important source of motivation and interest which will help keep you on track. - Page 11 OPERATIONAL INSTRUCTIONS 10/20 20/10 Custom REDAY Total Time LCD DISPLAY INSTRUCTIONS WORK TIME : Displays the time during exercise, from 1 second up to 1:59:59 hours. "0:00" for presetting the time for Target Time Program, from 1 second to 1:59:00 hours, and counts down from the preset value.
-
Page 12: Program Operation
OPERATIONAL INSTRUCTIONS PROGRAM OPERATION This computer contains the programs, Normal Program, Time, Distance, Calories, Heart-Rate, 10/20 Interval Program, 20/10 Interval Program, and Customer Setting Interval Program. Refer to the following for the operation of these programs. 1. NORMAL PROGRAM: You can pedaling to power on the computer. The LCD display will display... -
Page 13: Calories Program
OPERATIONAL INSTRUCTIONS 4. CALORIES PROGRAM: Press the TARGET CALORIES button, the LCD display will display "0" for presetting the target calories value, from 10 to 990 Kcals. This program is running. Use " / " buttons to input the value, and press ENTER button to exercise, the CALORIES readout... -
Page 14: Operation Descriptions
COMPUTER INSTRUCTIONS Cycles you had done. 7. 20/10 INTERVAL PROGRAM: This program is running. This program will allow the user to workout for 20 seconds, then rest for 10 seconds, and will cycle this way, the program 20/10 Custom preset eight cycles. Total Time Press 20/10 INTERVAL button, then the program is started. -
Page 15: Product Parts Drawing
PRODUCT PARTS DRAWING FRONT BACK... -
Page 16: Parts List
PARTS LIST PART# PART NAME Main Frame Fan Hub Fan Hub Spacer Fan Hub Sleeve Fan Shaft Bearing (6301Z) Bearing (6901Z) Left Fan Cage Right Fan Cage Plastic Strip Strip Holder Tension Bracket Eyelet Bolt (M8 x 1.25 x 45mm) Nut (M8 x 1.25) Crank Shaft Pulley... - Page 17 PARTS LIST PART# PART NAME Grommet Plug Left Handlebar Sensor Clip Bearing (6003Z) Bearing (6202Z) Bearing (6203Z) C Ring (S40 mm) Round Plug (Ø38 mm) Right Handlebar Sensor Wire Seat Post Sliding Post Adjustment Lever Connection Wire Pivot Axis Long Spring Set Block Short Spring Bushing (Ø8 x Ø12 x 7mm)
- Page 18 PARTS LIST PART# PART NAME Bolt, Socket Head (M6 x 1 x 35mm) Screw, Round Head (ST4 x 15mm) Screw, Flat Socket Head (M4 x 0.7 x 10mm) Bolt, Button Head (M8 x 1.25 x 40mm) Acorn Nut (M8 x 1.25) Screw, Round Head (M5 x 0.8 x 8mm) Bolt, Flat Socket Head (M8 x 1.25 x 30mm) Screw, Round Head (M5 x 0.8 x 12mm)
Need help?
Do you have a question about the OAF300 and is the answer not in the manual?
Questions and answers