Advertisement
MODEL WPMZ-5-□□□-□□-□□□
１８.
SPECIFICATIONS
MODEL CODES
WPMZ
5
ＷＰＭＺ－5
１
３
４
Ｐ
Ｌ
Ｘ
Ｐ
Ｌ
Ｘ
１
２
３
４
５
Ｅ
Ｆ
R
(*1) Combination of 2 inputs
The combination of a pulse input and an line driver input is NOT selectable.
(WPMZ-5-□PL and WPMZ-5-□LP are NOT available.)
Basic specifications
Number of
：
measurement
1 or 2
channel
Display
2.4 inch TFT liquid crystal display
：
Used in 1ch input ： Ach measurement result
Used in 2ch inputs ： Ach measurement result,
Bch measurement result, calculation result,
Ach and Bch measurement results,
Ach or Bch measurement result and calculation
result
Display range
0 to 999999
：
Zero display
Reading zero suppress
：
Decimal point
Settable freely
：
Over warning
By exceeding the range of display, displays OVER or
：
-OVER
Sampling rate
10ms（calculation period）
：
Display updating
100ms
：
period
External controls
5 functions of the followings can be assigned to
：
control terminals (user-configurable).
①Comparative output reset function
② Measurement inhibit function ： Measurement
inhibit A/B/A&B
③Current value hold function：Current value hold
A/B/A&B
④Maximum value hold function：Maximum value
hold A/B/A&B
⑤ Minimum value hold function ： Minimum value
hold A/B/A&B
⑥Pattern select function：Pattern select 1/2/3
⑦Display select function
⑧Trend Hold function
Ambient
-5 to 50℃ 35 to 85％RH（Non condensing）
：
temperature range
Storage
-10 to 70℃ up to 60％RH
：
temperature range
Supply power
AC power（WPMZ-5-1□□-□□-□□□）
：
AC100 to 240V±10%
DC power（WPMZ-5-3□□-□□-□□□）
DC12V±10%
DC power（WPMZ-5-4□□-□□-□□□）
DC24 to 48V±10%
Power
AC power（WPMZ-5-1□□-□□-□□□）
：
consumption
At AC100V：10VA max At AC240V：14VA max
DC power（WPMZ-5-3□□-□□-□□□）
At DC12V：6W max、
DC power（WPMZ-5-4□□-□□-□□□）
At DC24V：6W max、 At DC48V：6.5W max
Sensor power
Pulse input
DC 12V ±10% 100mA max.
DC24V±10% 50mA max.
*For 2ch inputs, allowable current of both Ach and
Tachometer/Speed Meter
Voltage power：AC100 to 240V
Voltage power：DC12V
Voltage power：DC24 to 48V
Pulse input
Line driver input
No Bch input
Pulse input （*1）
Line driver input （*1）
Display only（No output）
Analog output
BCD output （Opencollector NPN）
BCD output （Opencollector PNP）
RS-232C
RS-485（Modbus RTU）
Opencollector output （NPN）
Opencollector output （PNP）
Relay output （Normally open）
Ｘ
Test report：No test report
Ｔ
Test report：With test report
００
Standard (Initial language : Japanese)
Ｅ０ Initial language setting : English
（ according to model codes）
50／60Hz
Bch is same as above.
*Combine at DC12V, 24V: 1.2W max.
Line driver input
DC5V±10% 200mA max.
*For 2ch inputs, allowable current of both Ach and
Bch is same as above.
External
：
96mm（W）×52mm（H）×145mm（D）
dimensions
Weight
Approx. 350g
：
Withstand voltage
AC power （WPMZ-5-1□□-□□-□□□）
：
Between Power terminals and inputs/external
controls/comparative outputs/other outputs
AC3000V for 1 minute
DC power （WPMZ-5-3or4□□-□□-□□□）
Between Power terminals and inputs/external
controls/comparative outputs/other outputs
AC1500V for 1 minute
AC power and DC power
Between input terminals and external
controls/comparative outputs/other outputs
AC1500V for 1 minute
Between enclosure and each terminals AC3000V
for 1 minute
Insulation
Between terminals mentioned above, at DC500V
：
resistance
100MΩ or higher
Vibration
10 to 55Hz half amplitude 0.15mm in X,Y,Z
：
tolerance
directions for 30 minutes
Protective
：
IP66（front）
structure
Installation
：
indoor use
environment
Rated altitude
up to 2000m
：
Transient
：
Ⅱ
overvoltage
Measurement
：
Ⅱ
category
Pollution degree
2
：
Conformed EN
EN61326-1 （ EMS ： industrial
：
standard
environment／EMI：Class A）
(Applicable to line length only under 30m)
EN61010-1
EN50581
Material of
polycarbonate（PC） black UL94V-0
：
enclosure
Input Specifications
【Pulse input instantaneous measurement】
●Input specifications（common to Ach、Bch）
Frequency
0.01Hz to 500kHz (*2ch input:250kHz)
：
range
Input signal
Single ended
：
Open collector(NPN/PNP type),Voltage pulse, Totem
pole, AC pulse, Proximity sensor
Open collector
Input level
：
Pullup to 12V or 24V
Logic
L level： ≦1.0V
H level：3.9 to 30V （max. allowable voltage ±50V）
Zero Cross
AC60mV to 40V （max. allowable voltage 70V）
*AC signal which gets across 0V.
Input
Open collector
：
resistance
Pulled up to 12 V through approx. 10kΩ(in the case of
sensor power 12V）
Pulled up to 24 V through approx. 25kΩ(in the case of
sensor power 24V）
Pulled down to GND through approx. 10kΩ.
Logic/Zero Cross
Pulled down to GND through approx. 10kΩ
2 wire
Pulled down to GND through approx. 900Ω
Input pulse
≧ 0.9μs （both of L level and H level）
：
width
(2 channel inputs: ≧1.8 μs)
Measurement
Cyclic calculation method
：
method
Display unit
Can be selected one of second, minute, hour
：
time
Accuracy
±（20ppm rdg +1digit） @23±5℃
：
【Line driver input measurement】
●Input specifications （Common to Ach,Bch）
Conversion
0.01Hz to 500kHz (*2ch input:250kHz)
：
method
Input signal
Differential input (Line driver signal)
：
Input level
≧±1V（Differential voltage）
Input
330Ω
resistance
Maximum
±10V (Differential voltage)
allowable
voltage
Input pulse
≧ 0.9μs （both of L level and H level）
：
width
(2 channel inputs: ≧1.8 μs)
Measurement
Cyclic calculation method
：
method
Can be selected one of second, minute, hour
Display unit
：
11/12
electromagnetic
IM-0834-03
Advertisement
