Introduction; Specifications; Contents; Assembly - Sealey MS900PS Instructions

warninG! Wear approved eye safety protection, ear defenders and, if dust is generated, respiratory protection.
‰
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain and/ or tie back long hair.
9
Keep children and unauthorised persons away from the working area.
9
secure non-stable work piece with a clamp, vice or other adequate holding device.
9
Remove adjusting keys and wrenches from the machine and its vicinity before turning it on.
9
do noT use equipment for any purpose other than that for which it is designed.
8
do noT operate the polisher/sander if any parts are damaged or missing as this may cause failure or possible personal injury.
8
warninG! do noT sand any materials containing asbestos.
‰
do noT switch the polisher/sander on whilst the head is in contact with the work piece and avoid unintentional starting.
8
do noT get the polisher/sander wet or use in damp or wet locations or areas where there is condensation.
8
do noT allow untrained persons to operate the polisher/sander.
8
do noT operate the polisher/sander when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
do noT use the polisher/sander where there are flammable liquids, solids or gases such as paint solvents, etc.
8
do noT leave the polisher/sander operating unattended.
8
do noT carry the polisher/sander with your finger on the power switch.
8
do noT pull the cord to remove the plug from the power supply.
8
Use a qualified person to lubricate and maintain the polisher/sander.
9
When not in use unplug from the mains power supply and store in a safe, dry, childproof area.
9
lead painT warninG! Paint once contained lead as a traditional ingredient. contact with the dust from the removal of such paint is
toxic and must therefore be avoided. the following action must be taken before using machine as a sander:
1. User must determine potential hazard relating to age of paint to be removed. (Modern paints do not have lead content).
2. danGer! Keep all persons and pets away from the working area. the following are particularly vulnerable to the effects of lead
paint dust: expectant women, babies and children.
3. We recommend personal protection by using the following safety items:
A) Paint Spray Respirator (Sealey ref. SSP1699) B) PE Coated Hooded Coverall (Sealey ref. SSP266). C) Latex Gloves
(sealey ref. ssP24).
4. Take adequate measures to contain paint dust, flakes and scrapings. Wear safety equipment, as in (3) above and thoroughly
clean all areas when task is complete.
5. ensure the paint waste is disposed of in sealed bags or containers according to local regulations.

2. inTroduCTion

Variable speed control for sanding and polishing. speed varies from 1000 to 3000rpm. Alloy bevel gear head with composite motor housing.
supplied with Ø170mm backing pad and side handle.

3. speCiFiCaTions

model no: ............................................................... ms900Ps
Pad size: ................................................................. Ø170mm
thread size: ........................................................ m14 x 2mm
no load speed: .............................................. 1000 - 3000rpm
Power: .........................................................................1300W
supply: ...........................................................................230V
Weight: .......................................................................... 3.8kg
noise power: ..............................................................102lwa
noise pressure: ............................................................ 91lpa
Vibration: ................................................................ 7.678m/s²
uncertainty: ..................................................................... 1.5k

4. ConTenTs

Refer to fig.1
1: Polisher unit, 2: side Handle, 3: Pad, 4: spanner.

5. assemblY

warninG! ensure unit is not plugged into mains before
‰
attempting any assembly.
5.1. Attach the side handle (fig.1.2). note: there is a mounting hole on either side and the top to suit the application and/or operator.
5.2. to attach the rubber pad:
thread the rubber pad (fig.1.3) on shaft and tighten using spanner (fig.1.4) by holding shaft steady with locking button (fig.2).
5.3. to fit a sanding disc:
select the grade of self adhesive sanding disc required, peel off the backing and centrally locate the disc onto the rubber pad.
5.4. to fit a polishing bonnet:
fit the polishing bonnet over the secured rubber pad, using the pull cord, tighten the bonnet and tie a bow to secure, tuck the loose
ends of the bow neatly under the bonnet.
© Jack sealey limited
Fig.1
2
Original Language Version
1
3
4
ms900Ps | issue 4 (sP) 10/10/17