1 Safety Precautions 1.1. General guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
Page 5
1.2.1. Micro Fuse conducting check This unit uses the Micro Fuse. Check the Micro Fuse conducting using the Tester at the check points below.
2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec- trostatic Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semi- conductor "chip"...
2.2. Service caution based on legal restrictions 2.2.1. General description about Lead Free Solder (PbF) The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation. The normal solder is the alloy of tin (Sn) and lead (Pb).
3 Service Navigation 3.1. Combination of Multiple Pressing on the Remote Control Press multi-buttons (in combination) on the remote control simultaneously for operations, such as initialization or service mode, etc. There are no multiple pressing functions on the previous remote controls, thus, please be sure to use the supplied remote control. 3.2.
Page 10
3.2.2. Nondisclosure mode 1 (Combination of multiple pressing: [6] [7] [Yellow]) Press and hold [6] [7] [Yellow] on the remote control simultaneously for 5 sec., then [50 RET] is displayed on FL display window. 3.2.3. Nondisclosure mode 2 (Combination of multiple pressing: [5] [9] [Red]) Press and hold [5] [9] [Red] on the remote control simultaneously for about 5 sec., then "70 RET"...
4 Specifications BD-Video (Blu-ray 3D, BD-ROM Version 2.4 BD-LIVE, BONUSVIEW): BD-RE: Version3 (Single Layer/Dual Layer), JPEG, MPO Power supply: AC220-240V, 50/60Hz BD-R: Version2 (Single Layer/Dual (BDTGA/GC) Layer),DivX( BDTGA/GC/GN/GT/ AC220-240V, 50Hz PU *4, *5, *6), MKV(*4, *6, *7) (BDT110GN) DVD-R: DVD-Video format (*1), DVD AC110V, 60Hz Video Recording format(*1), (BDT110GT)
Page 12
Maximum numbers of folders and files: *11: Total of the JPEG and MPO MP3: CD-R, CD-RW, DVD-R, USB device: Compression rate: 32kbps~320kbps Sampling rate: 44.1kHz, 48kHz AVCHD (H.264): SD card, DVD: AVCHD format V1.0 HDMI: 480p(525p)/ 576p(625p)(BDT110GA/GC/GN/ GT)/1080i(1125i)/720p(750p)/ 1080p(1125p) HDMI (V.1.4a with 3D, Content Type) (This unit supports “HDAVI Control 5”...
5 Service Mode 5.1. Self-Diagnosis and Special Mode Setting 5.1.1. Self-Diagnosis Functions Self-Diagnosis Function provides information for errors to service personnel by “Self-Diagnosis Display” when any error has occurred. U** and F** are stored in memory and held. You can check latest error code by transmitting [0] [1] of Remote Controller in Service Mode. Automatic Display on FL will be cancelled when the power is turned off or AC input is turned off during self-diagnosis display is ON.
Page 14
Error Code Diagnosis contents Description Monitor Display Automatic FL display Initialization error When initialization error is detected after start- No display No display ing up main microprocessor, the power is turned off automatically. The event is saved in memory. Drive hardware error When drive unit error is detected, the event is No display No display...
Page 15
5.1.2. Special Modes Setting Item FL display Key operation Mode name Description Front Key Rating password The audiovisual level setting password is While the unit is on, press and initialized to Level 8. hold [OK], [B] and [Y] on the remote control at the same time for more than 5 seconds.
Page 16
Item FL display Key operation Mode name Description Front Key Aging Perform sequence of modes as * Aging Display following the then mode. Turn the power on. Description shown below continually. Press the [5] [9] and [R] button simultaneously for five seconds, then [70 RET] is displayed on FL.
Page 17
Item FL display Key operation Mode name Description Front Key Demonstration Ejection of the disc is prohibited. *When lock the tray. When the power is on, disc is in lock/unlock The lock setting is effective until unlocking the tray, press and hold [OK], [B] and tray and not released by Main unit [Y] on the remote control at the initialization of service mode.
Page 18
5.1.3. Service Modes at a glance Information necessary for service can be displayed. Service mode setting: 1. Turn the power off. 2. Press the [5] [9] and [R] button simultaneously for five seconds, then [70 RET] is displayed on FL. 3.
Page 19
Item FL display Key operation Mode name Description (Remote controller key) Drive application check Checking whether the drive is applicable drive Press [0] [3] in service mode. or not. Drive Check Simple quality of BD drive Press [3][8] in service mode. *If the date of the present or the trouble occurred time is incorrect, it may be not able to judge correctly.
Page 20
Item FL display Key operation Mode name Description (Remote controller key) BD drive last error BD drive error code display. 1. Error Number is displayed for 5 Press [4] [2] in service mode. seconds. 2. Time when the error has occurred is display for 5 seconds.
Page 21
Item FL display Key operation Mode name Description (Remote controller key) 6. Disc maker ID is displayed for 5 In case that the maker cannot be seconds. identified, display is blackout. 7. Factor of drive error (hexadeci- mal) occurring is left displayed.
Page 22
Item FL display Key operation Mode name Description (Remote controller key) 8. When the last error doesn't exist . CEC (H) output check Check of the CEC terminal high output of Press [5] [5] in service mode. HDMI. CEC (L) output check Check of the CEC terminal low output of Press [5] [6] in service mode.
Page 23
Item FL display Key operation Mode name Description (Remote controller key) Drive adjustment value Initialize the drive going to factory production Press[7][1]in service mode. initialization adjustment values. Wirte remote control number key perform the initialization. Initializing: Successful adjustment value initial- ization and automatic adjustment time : Failed at initialization and auto-...
6 Service Fixture & Tools Part Number Description Compatibility RFKZ0216 Extension Cable (Digital P.C.B. - Power P.C.B. / 23 Pin) Same as BD60 Series RFKZ0327 Extension Cable (Digital P.C.B. - SD P.C.B. / 15 Pin) Same as XW350 Series RFKZ03D01KS Lead Free Solder (0.3mm/100g Reel) Same as BD60 Series RFKZ06D01KS...
7 Measurements and Adjustments 7.1. Service Positions Note: For description of the disassembling procedure, see the section 9. (Vol. 1) 7.1.1. Checking and Repairing of Digital P.C.B.
7.2. Adjustment 7.2.1. Adjustment of BDT110GA/GC/GN/GT/GW NOTE: Please do the adjustment according to the following steps. 7.2.1.1. Drive OPU-QR Code write(72) In the service mode, enter 6 digits QR Code after numeral keys are input on the remote control. Enter in service mode.
7.3. The encryption between CPU and Nand-Flash The encryption processing is executed by this operation between CPU and Nand-Flash. Nand-Flash that executes the encryption cannot never be encrypted again with other CPU. When CPU is exchanged, it is necessary to exchange Nand-Flash at the same time.
11 Appendix for Schematic Diagram 11.1. Voltage and Waveform Chart NOTE: Circuit voltage and waveform described herein shall be regarded as reference information when probing defect point, because it may differ from an actual measuring value due to difference of Measuring instrument and its measuring condition and product itself.
Page 56
IC59020 Ref No. MODE PLAY STOP IC59020 Ref No. MODE PLAY STOP IC59020 IC59301 Ref No. MODE PLAY STOP IC59306(BDT110GA/GN/GW/PU/PX) IC59307(BDT110GA/GN/GW/PU/PX) IC59303 Ref No. MODE PLAY STOP Q55009(BDT110PU/PX) Q56301 Q58003 Ref No. MODE 12.0 12.0 PLAY 12.0 12.0 STOP Q58004 Q58006 Ref No.
12 Replacement Parts List 12.1. Electrical Replacement Parts List Notes: Safety Ref. Part No. Part Name & Pcs Remarks *Important safety notice: Description C51008 F1G1A104A058 10V 0.1U BDT110GC Components identified by mark have special character- istics important for safety. C51010 F1G1A1040006 10V 0.1U BDT110GA Furthermore, special parts which have purposes of...
Page 60
Safety Ref. Part No. Part Name & Pcs Remarks Safety Ref. Part No. Part Name & Pcs Remarks Description Description C51041 F1G1A1040006 10V 0.1U BDT110GA C51060 F1G1A104A058 10V 0.1U BDT110GC /GN/GW/ PU/PX C51061 F1G1A1040006 10V 0.1U BDT110GA C51041 F1G1A104A058 10V 0.1U BDT110GC /GN/GW/ PU/PX...
Page 61
Safety Ref. Part No. Part Name & Pcs Remarks Safety Ref. Part No. Part Name & Pcs Remarks Description Description C52011 F1G1A104A058 10V 0.1U BDT110GC C52201 F1G1A1040006 10V 0.1U BDT110GA /GN/GW/ PU/PX C52012 F1G1A1040006 10V 0.1U BDT110GA /GN/GW/ C52201 F1G1A104A058 10V 0.1U BDT110GC PU/PX C52012...
Page 62
Safety Ref. Part No. Part Name & Pcs Remarks Safety Ref. Part No. Part Name & Pcs Remarks Description Description C54015 F1H1H102A004 50V 1000P BDT110GA C55122 F1G1C104A077 16V 0.1U BDT110PU /GC/GN/ GT/GW C56024 F1G0J105A031 6.3V 1U C55011 F1G1A104A012 10V 0.1U C56025 F1G0J105A031 6.3V 1U C55012...
Page 63
Safety Ref. Part No. Part Name & Pcs Remarks Safety Ref. Part No. Part Name & Pcs Remarks Description Description C59301 F1G1A104A058 10V 0.1U BDT110GC IC57005 C0EBK0000206 IC E.S.D. IC57006 C0CBCBC00227 IC E.S.D. C59315 F1H1A105A028 10V 1U IC58003 C0DBAYY00462 IC E.S.D.
Page 64
Safety Ref. Part No. Part Name & Pcs Remarks Safety Ref. Part No. Part Name & Pcs Remarks Description Description P58001 K1KY23AA0607 CONNECTOR(23P) R55033 ERJ2GEJ563X 1/16W 56K BDT110PU P59301 K1KY15AA0607 CONNECTOR(15P) R55059 ERJ2GEJ272X 1/16W 2.7K P59302 K1FY104BA073 JACK USB BDT110GA /GN/GW/ R55079 ERJ2GEJ103X...