All manuals and user guides at all-guides.com TABLE OF CONTENTS PAGE PAGE 8.4. Digital (Front End Section) Block Diagram -------- 32 1 Safety Precautions----------------------------------------------- 4 1.1. General guidelines ---------------------------------------- 4 8.5. Analog Audio/Video Block Diagram ----------------- 33 1.2. Caution for fuse replacement--------------------------- 4 9 Schematic Diagram -------------------------------------------- 34 1.3.
All manuals and user guides at all-guides.com 1 Safety Precautions 1.1. General guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2.
Page 5
All manuals and user guides at all-guides.com 1.2.1. Micro Fuse conducting check This unit uses the Micro Fuse. Check the Micro Fuse conducting using the Tester at the check points below.
All manuals and user guides at all-guides.com 2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec- trostatic Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semi- conductor "chip"...
All manuals and user guides at all-guides.com 2.2. Service caution based on legal restrictions 2.2.1. General description about Lead Free Solder (PbF) The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation.
All manuals and user guides at all-guides.com 3 Service Navigation 3.1. Combination of Multiple Pressing on the Remote Control Press multi-buttons (in combination) on the remote control simultaneously for operations, such as initialization or service mode, etc. There are no multiple pressing functions on the previous remote controls, thus, please be sure to use the supplied remote control. 3.2.
Page 10
All manuals and user guides at all-guides.com 3.2.2. Nondisclosure mode 1 (Combination of multiple pressing: [6] [7] [Yellow]) Press and hold [6] [7] [Yellow] on the remote control simultaneously for 5 sec., then [50 RET] is displayed on FL display window. 3.2.3.
All manuals and user guides at all-guides.com 4 Specifications BD-Video (Blu-ray 3D, BD-ROM Version 2.4 BD-LIVE, BONUSVIEW): BD-RE: Version3 (Single Layer/Dual Layer), JPEG, MPO Power supply: AC220-240V, 50/60Hz BD-R: Version2 (Single Layer/Dual (BDTGA/GC) Layer),DivX( BDTGA/GC/GN/GT/ AC220-240V, 50Hz PU *4, *5, *6), MKV(*4, *6, *7) (BDT110GN) DVD-R: DVD-Video format (*1), DVD...
Page 12
All manuals and user guides at all-guides.com Maximum numbers of folders and files: *11: Total of the JPEG and MPO MP3: CD-R, CD-RW, DVD-R, USB device: Compression rate: 32kbps~320kbps Sampling rate: 44.1kHz, 48kHz AVCHD (H.264): SD card, DVD: AVCHD format V1.0 HDMI: 480p(525p)/ 576p(625p)(BDT110GA/GC/GN/...
All manuals and user guides at all-guides.com 5 Service Mode 5.1. Self-Diagnosis and Special Mode Setting 5.1.1. Self-Diagnosis Functions Self-Diagnosis Function provides information for errors to service personnel by “Self-Diagnosis Display” when any error has occurred. U** and F** are stored in memory and held. You can check latest error code by transmitting [0] [1] of Remote Controller in Service Mode.
Page 14
All manuals and user guides at all-guides.com Error Code Diagnosis contents Description Monitor Display Automatic FL display Initialization error When initialization error is detected after start- No display No display ing up main microprocessor, the power is turned off automatically. The event is saved in memory.
Page 15
All manuals and user guides at all-guides.com 5.1.2. Special Modes Setting Item FL display Key operation Mode name Description Front Key Rating password The audiovisual level setting password is While the unit is on, press and initialized to Level 8. hold [OK], [B] and [Y] on the remote control at the same time for more than 5 seconds.
Page 16
All manuals and user guides at all-guides.com Item FL display Key operation Mode name Description Front Key Aging Perform sequence of modes as * Aging Display following the then mode. Turn the power on. Description shown below continually. Press the [5] [9] and [R] button simultaneously for five seconds, then [70 RET] is displayed on FL.
Page 17
All manuals and user guides at all-guides.com Item FL display Key operation Mode name Description Front Key Demonstration Ejection of the disc is prohibited. *When lock the tray. When the power is on, disc is in lock/unlock The lock setting is effective until unlocking the tray, press and hold [OK], [B] and tray and not released by Main unit [Y] on the remote control at the...
Page 18
All manuals and user guides at all-guides.com 5.1.3. Service Modes at a glance Information necessary for service can be displayed. Service mode setting: 1. Turn the power off. 2. Press the [5] [9] and [R] button simultaneously for five seconds, then [70 RET] is displayed on FL. 3.
Page 19
All manuals and user guides at all-guides.com Item FL display Key operation Mode name Description (Remote controller key) Drive application check Checking whether the drive is applicable drive Press [0] [3] in service mode. or not. Drive Check Simple quality of BD drive Press [3][8] in service mode.
Page 20
All manuals and user guides at all-guides.com Item FL display Key operation Mode name Description (Remote controller key) BD drive last error BD drive error code display. 1. Error Number is displayed for 5 Press [4] [2] in service mode. seconds.
Page 21
All manuals and user guides at all-guides.com Item FL display Key operation Mode name Description (Remote controller key) 6. Disc maker ID is displayed for 5 In case that the maker cannot be seconds. identified, display is blackout. 7. Factor of drive error (hexadeci- mal) occurring is left displayed.
Page 22
All manuals and user guides at all-guides.com Item FL display Key operation Mode name Description (Remote controller key) 8. When the last error doesn't exist . CEC (H) output check Check of the CEC terminal high output of Press [5] [5] in service mode. HDMI.
Page 23
All manuals and user guides at all-guides.com Item FL display Key operation Mode name Description (Remote controller key) Drive adjustment value Initialize the drive going to factory production Press[7][1]in service mode. initialization adjustment values. Wirte remote control number key perform the initialization. Initializing: Successful adjustment value initial- ization and automatic adjustment...
All manuals and user guides at all-guides.com 6 Service Fixture & Tools Part Number Description Compatibility RFKZ0216 Extension Cable (Digital P.C.B. - Power P.C.B. / 23 Pin) Same as BD60 Series RFKZ0327 Extension Cable (Digital P.C.B. - SD P.C.B. / 15 Pin) Same as XW350 Series RFKZ03D01KS Lead Free Solder (0.3mm/100g Reel)
All manuals and user guides at all-guides.com 7 Measurements and Adjustments 7.1. Service Positions Note: For description of the disassembling procedure, see the section 9. (Vol. 1) 7.1.1. Checking and Repairing of Digital P.C.B.
All manuals and user guides at all-guides.com 7.2. Adjustment 7.2.1. Adjustment of BDT110GA/GC/GN/GT/GW NOTE: Please do the adjustment according to the following steps. 7.2.1.1. Drive OPU-QR Code write(72) In the service mode, enter 6 digits QR Code after numeral keys are input on the remote control.
All manuals and user guides at all-guides.com 7.3. The encryption between CPU and Nand-Flash The encryption processing is executed by this operation between CPU and Nand-Flash. Nand-Flash that executes the encryption cannot never be encrypted again with other CPU. When CPU is exchanged, it is necessary to exchange Nand-Flash at the same time.
All manuals and user guides at all-guides.com 11 Appendix for Schematic Diagram 11.1. Voltage and Waveform Chart NOTE: Circuit voltage and waveform described herein shall be regarded as reference information when probing defect point, because it may differ from an actual measuring value due to difference of Measuring instrument and its measuring condition and product itself.
Page 56
All manuals and user guides at all-guides.com IC59020 Ref No. MODE PLAY STOP IC59020 Ref No. MODE PLAY STOP IC59020 IC59301 Ref No. MODE PLAY STOP IC59306(BDT110GA/GN/GW/PU/PX) IC59307(BDT110GA/GN/GW/PU/PX) Ref No. IC59303 MODE PLAY STOP Q55009(BDT110PU/PX) Q56301 Q58003 Ref No. MODE 12.0 12.0 PLAY...
Page 57
All manuals and user guides at all-guides.com 11.1.2. Abbreviations INITIAL/LOGO ABBREVIATIONS INITIAL/LOGO ABBREVIATIONS A0~UP ADDRESS IECOUT IEC958FORMATDATAOUTPUT ACLK AUDIO CLOCK IPFRAG INTERPOLATIONFLAG AD0~UP ADDRESS BUS IREF I(CURRENT)REFERENCE ADATA AUDIO PES PACKET DATA ISEL INTERFACEMODESELECT ADDRESS LATCH ENABLE LDON LASERDIODECONTROL AMUTE AUDIO MUTE LASERPOWERCONTROL AREQ...
Page 58
All manuals and user guides at all-guides.com INITIAL/LOGO ABBREVIATIONS TRACKING ERROR TIBAL BALANCE CONTROL BALANCE OUTPUT 1 BALANCE INPUT BALANCE INPUT BALANCE OUTPUT 2 TPSN OP AMP INPUT TPSO OP AMP OUTPUT TPSP OP AMP INVERTED INPUT TRCRS TRACK CROSS SIGNAL TRON TRACKING ON TRSON...
All manuals and user guides at all-guides.com 12 Replacement Parts List 12.1. Electrical Replacement Parts List Notes: Safety Ref. Part No. Part Name & Pcs Remarks *Important safety notice: Description C51008 F1G1A104A058 10V 0.1U BDT110GC Components identified by mark have special character- istics important for safety.
Page 60
All manuals and user guides at all-guides.com Safety Ref. Part No. Part Name & Pcs Remarks Safety Ref. Part No. Part Name & Pcs Remarks Description Description C51041 F1G1A1040006 10V 0.1U BDT110GA C51060 F1G1A104A058 10V 0.1U BDT110GC /GN/GW/ PU/PX C51061 F1G1A1040006 10V 0.1U BDT110GA C51041...
Page 61
All manuals and user guides at all-guides.com Safety Ref. Part No. Part Name & Pcs Remarks Safety Ref. Part No. Part Name & Pcs Remarks Description Description C52011 F1G1A104A058 10V 0.1U BDT110GC C52201 F1G1A1040006 10V 0.1U BDT110GA /GN/GW/ PU/PX C52012 F1G1A1040006 10V 0.1U BDT110GA /GN/GW/...
Page 62
All manuals and user guides at all-guides.com Safety Ref. Part No. Part Name & Pcs Remarks Safety Ref. Part No. Part Name & Pcs Remarks Description Description C54015 F1H1H102A004 50V 1000P BDT110GA C55122 F1G1C104A077 16V 0.1U BDT110PU /GC/GN/ GT/GW C56024 F1G0J105A031 6.3V 1U C55011 F1G1A104A012 10V 0.1U...
Page 63
All manuals and user guides at all-guides.com Safety Ref. Part No. Part Name & Pcs Remarks Safety Ref. Part No. Part Name & Pcs Remarks Description Description C59301 F1G1A104A058 10V 0.1U BDT110GC IC57005 C0EBK0000206 IC E.S.D. IC57006 C0CBCBC00227 IC E.S.D. C59315 F1H1A105A028 10V 1U IC58003 C0DBAYY00462 IC...
Page 64
All manuals and user guides at all-guides.com Safety Ref. Part No. Part Name & Pcs Remarks Safety Ref. Part No. Part Name & Pcs Remarks Description Description P58001 K1KY23AA0607 CONNECTOR(23P) R55033 ERJ2GEJ563X 1/16W 56K BDT110PU P59301 K1KY15AA0607 CONNECTOR(15P) R55059 ERJ2GEJ272X 1/16W 2.7K P59302 K1FY104BA073 JACK USB...
Page 65
All manuals and user guides at all-guides.com Safety Ref. Part No. Part Name & Pcs Remarks Description RX55010 D1H81034A024 RESISTOR-RESISTOR RX55012 D1H84734A024 RESISTOR-RESISTOR RX55015 D1H83334A024 RESISTOR-RESISTOR RX55016 D1H83334A024 RESISTOR-RESISTOR RX55017 D1H81034A024 RESISTOR-RESISTOR RX55018 D1H81024A024 RESISTOR-RESISTOR RX56314 D1H82224A024 RESISTOR-RESISTOR RX56315 D1H81014A024 RESISTOR-RESISTOR RX57001 D1H81014A024 RESISTOR-RESISTOR RX57002 D1H81014A024 RESISTOR-RESISTOR RX57003 D1H81024A024 RESISTOR-RESISTOR...