Table of Contents
Advertisement
Quick Links
Instructions
Fill Valve
Refill manifold for use with Graco Auto-Fill Shut Off Valve only. For professional use only.
Part No.:
77X542
132230
5000 psi (34.4 MPa, 344.7 bar) Maximum Working
Pressure
Part No. 132230: 3000 psi (20.7 MPa, 206.8 bar)
Important Safety Instructions
Read all warnings and instructions in this
manual and in Electric DynaStar and Auto-Fill
Shut Off Valve Instruction manuals. Save all
instructions.
333393D
EN
Advertisement
Table of Contents
Related Manuals for Graco 77X542
Summary of Contents for Graco 77X542
- Page 1 Instructions Fill Valve 333393D Refill manifold for use with Graco Auto-Fill Shut Off Valve only. For professional use only. Part No.: 77X542 132230 5000 psi (34.4 MPa, 344.7 bar) Maximum Working Pressure Part No. 132230: 3000 psi (20.7 MPa, 206.8 bar)
- Page 2 Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.
-
Page 3: Typical Installation
Installation Installation Typical Installation Fill Valve *Supply Hose (user supplied) Dyna-Star Pump Drain Hose Auto-Fill Shut Off Valve Fill Stud Auto-Fill Inlet Operating Instructions Label Reservoir Fill Valve Outlet Reservoir Port (vent line) Fill Valve Vent Port Remote Filling Station Reservoir Filter (recommended if grease/environment is Remote Filling Station Pump (pneumatic) contaminated) - Page 4 Installation Fill Valve Component Installation Identification The reference letters used in the following instructions refer to the Typical Installation diagram provided on page 3 and the Component Identification illustration (F . 1). 1. Select the installation location. Be sure the installa- tion location chosen is clean, flat and easily accessi- 2.
-
Page 5: Operation
Installation Operation 6. Start Remote Filling Station Pump (H). 7. When Reservoir (E) is filled: • the Remote Filling Station Pump (H) stalls (dead-heads), The remote filling station pump stalls (dead-heads) • the Auto-Fill Shut Off pin pops up as shown in when the reservoir is full, causing the supply system . -
Page 6: Troubleshooting
Troubleshooting Troubleshooting Pressure Relief Procedure Follow the Pressure Relief Procedure whenever you see this symbol. This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure Relief Procedure when you stop dispensing and before cleaning, checking, or servicing the equipment. -
Page 7: Technical Specifications
3000 psi + 10% 20.7 MPa, 206.8 bar + 10% Maximum fluid flow 2 gpm 7.57 lpm Outlet port size Model 77X542, 132230 3/4 inch npt Vent port size Model 77X542, 132230 3/8 inch npt Inlet ISO 7241-1, Series B standard hydraulic quick disconnect... -
Page 8: Dimensions And Mounting
For the latest information about Graco products, visit www.graco.com. For patent information, see www.graco.com/patents. TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590 All written and visual data contained in this document reflects the latest product information available at the time of publication.