Hobart Welding Products H100S4-10 Owner's Manual page 15

Warranty Questions?
Call
1-800-332-3281
8 AM − 5 PM EST
Service
You always get the fast,
reliable response you
need. Most replacement
parts can be in your
hands in 24 hours.
Support
Need fast answers to the
tough welding questions?
Contact your distributor or
call 1-800-332-3281. The
expertise of the distributor
and Hobart is there to
help you, every step of
the way.
Assistance
Visit the Hobart website:
www.HobartWelders.com
5/3/1 WARRANTY applies to all Hobart welding equipment, plasma cutters and spot welders with a
This limited warranty supersedes all previous Hobart warranties and is exclusive with
no other guarantees or warranties expressed or implied.
Hobart products are serviced by Hobart or Miller Authorized Service Agencies.
LIMITED WARRANTY − Subject to the terms and conditions
below, Miller Electric Mfg. LLC, dba Hobart Welding Products,
Appleton, Wisconsin, warrants to its original retail purchaser that
new Hobart equipment sold after the effective date of this limited
warranty is free of defects in material and workmanship at the time
it is shipped. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
Within the warranty periods listed below, Hobart/Miller will repair or
replace any warranted parts or components that fail due to such
defects in material or workmanship. Hobart/Miller must be notified
in writing within thirty (30) days of such defect or failure, at which
time Hobart/Miller will provide instructions on the warranty claim
procedures to be followed. If notification is submitted as an online
warranty claim, the claim must include a detailed description of the
fault and the troubleshooting steps taken to identify failed
components and the cause of their failure.
Hobart/Miller shall honor warranty claims on warranted equipment
listed below in the event of such a failure within the warranty time
periods. All warranty time periods start on the delivery date of the
equipment to the original retail purchaser, and not to exceed twelve
months after the equipment is shipped to a North American
distributor or twelve months after the equipment is shipped to an
International distributor.
1. 5 Years — Parts and Labor
* Original Main Power Rectifiers only to include SCRs,
diodes, and discrete rectifier modules
* Reactors
* Stabilizers
* Transformers
2. 3 Years — Parts and Labor
* Drive Systems
* Idle Module
* PC Boards
* Rotors, Stators and Brushes
* Solenoid Valves
* Spot Welder Transformer
* Switches and Controls
* MIG Flowgauge Regulators (No Labor)
3. 1 Year — Parts and Labor Unless Specified
(90 days for industrial use)
* Accessories
* Batteries (Trek 180 Only)
* Contactors
* Field Options
(NOTE: Field options are covered for the remaining
warranty period of the product they are installed in, or
for a minimum of one year — whichever is greater.)
* HF Units
* MIG Guns/TIG Torches
* Motor-Driven Guns
* Plasma Cutting Torches
* Relays
* Remote Controls
* Replacement Parts (No labor) − 90 days
* Running Gear/Trailers
* Water Cooling Systems
* Spoolguns
Effective January 1, 2018
serial number preface of MJ or newer.
4. 6 Months — Parts
* Batteries
5. Engines and tires are warranted separately by the
manufacturer.
Hobart's 5/3/1 Limited Warranty shall not apply to:
1. Consumable components; such as contact tips,
cutting nozzles, contactors, brushes, relays, work
station table tops and welding curtains, or parts that
fail due to normal wear. (Exception: brushes and
relays are covered on all engine-driven products.)
2. Items furnished by Hobart/Miller, but manufactured by
others, such as engines or trade accessories. These
items are covered by the manufacturer's warranty, if any.
3. Equipment that has been modified by any party other than
Hobart/Miller, or equipment that has been improperly
installed, improperly operated or misused based upon
industry standards, or equipment which has not had
reasonable and necessary maintenance, or equipment
which has been used for operation outside of the
specifications for the equipment.
HOBART PRODUCTS ARE INTENDED FOR COMMERCIAL AND
INDUSTRIAL USERS TRAINED AND EXPERIENCED IN THE USE
AND MAINTENANCE OF WELDING EQUIPMENT.
The exclusive
Hobart's/Miller's option, either: (1) repair; or (2) replacement; or, if
approved in writing by Hobart/Miller, (3) the pre-approved cost of
repair or replacement at an authorized Hobart/Miller service
station; or (4) payment of or credit for the purchase price (less
reasonable depreciation based upon use). Products may not be
returned without Hobart's/Miller's written approval. Return
shipment shall be at customer's risk and expense.
The above remedies are F.O.B. Appleton, WI, or Hobart's/Miller's
authorized service facility. Transportation and freight are the
customer's responsibility. TO THE EXTENT PERMITTED BY
LAW, THE REMEDIES HEREIN ARE THE SOLE AND
EXCLUSIVE REMEDIES REGARDLESS OF THE LEGAL
THEORY. IN NO EVENT SHALL HOBART/MILLER BE LIABLE
FOR DIRECT,
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF PROFIT)
REGARDLESS OF THE LEGAL THEORY. ANY WARRANTY
NOT PROVIDED HEREIN AND ANY IMPLIED WARRANTY,
GUARANTY, OR REPRESENTATION,
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR PARTICULAR PURPOSE, ARE EXCLUDED AND
DISCLAIMED BY HOBART/MILLER.
Some US states do not allow limiting the duration of an implied
warranty or the exclusion of certain damages, so the above
limitations may not apply to you. This warranty provides specific
legal rights, and other rights may be available depending on your
state. In Canada, some provinces provide additional warranties or
remedies, and to the extent the law prohibits their waiver, the
limitations set out above may not apply. This Limited Warranty
provides specific legal rights, and other rights may be available,
but may vary by province.
remedies for warranty claims are,
INDIRECT, SPECIAL, INCIDENTAL
INCLUDING ANY
hobart_warr 2018-03
at
OR