Table of Contents
Advertisement
Connecting
your portable dishwasher
A special
adapter
must be installed
on the faucet
before
the dishwasher
can
be connected.
Complete
instructions
and
the adapter
are packed
with your
dishwasher.
When
moving
your
dishwasher,
make
sure
the door is latched.
Before starting
3.
4.
5.
6.
7.
Run water at faucet
until it is hot. Turn it off.
PULL RING
Pull hoses out oftheir
storage
compartment
on the back.
LOCKING
COLLAR
/
L
HOSE CONNECTOR
Pull down
on the locking
collar
while
lifting
the hose connector
onto the faucet adapter.
When the connector
snaps
into place,
re-
lease the locking
collar.
Turn the hot water
on slowly
until it is all the
way on.
Plug in power
supply
cord.
See pages
8 and 9 to start the dishwasher.
While
dishwasher
is running
You can draw water from the faucet while the
dishwasher
is connected.
DO NOT draw water
while the dishwasher
is filling
or while water
is
being
pumped
out. [This helps prevent
a low fill
when dishwasher
is filling, or mixing
drain water
with fresh water.]
Your Whirlpool
Portable
Dishwasher
can be
converted
to a built-in
(undercounter)
model
by using conversion
kit No. 569056.
The kit is
available
at your Whirlpool
dealer
or autho-
rized
TECH-CARE'
Service
Company.
Instruc-
tions are included
with the kit.
Caring
for
1. Press red button
on hose connector
to get
the water you want. (The faucet
is set on hot.
Adjust faucet
for the water you want.)
2. Be sure you return
cold
water
to off, and
that hot water
is full on.
simulated
wood top
When cycle is finished
1. Turn hot water off (This can be done after the
last rinse.]
The simulated
wood
top can be used as a
utility work surface
for most kitchen
jobs. It is
stronger
and more easily
cleaned
than genu-
ine wood.
The top can be used as a cutting
board.
Knife
marks will be visible
but will not seriously
dam-
age top. Hot items from the oven can be placed
on the top
2. Press the red button
on the connector
to re-
Clean
with warm,
soapy
water.
For dried
on
lease the water pressure.
foods, use a scouring
pad.
3.
4.
5.
6.
Lift slightly
on the hose connector
while pull-
ing down
the locking
collar.
Pull down
on
the connector.
Empty
any
remaining
water
from
the
connector.
Unplug
power
supply
cord
and
return to
storage
compartment.
Return hoses to storage
compartment.
Electrical
Connection
A power supply of 120 volts, 60 Hz or110 volts, 50 Hz,
AC only, 15 amps, is required.
For your personal
safety, this appliance
must be grounded.
This ap-
pliance
is equipped
with a power
supply
cord
having
a 3-prong
grounding
plug. To minimize
possible
shock hazard
it must be plugged
into a
mating
J-prong
grounding
type wall receptacle,
grounded
in accordance
with the National
Elec-
trical Code and local codes and ordinances.
If a
mating
wall receptacle
is not available,
it is the
personal
responsibility
and obligation
of the cus-
tomer to have a properly
grounded
3-prong
wall
receptacle
installed
by a qualified
electrician.
DO NOT use an extension
cord.
Power Supply
Cord
DO NOT, UNDER ANY CIRCUMSTANCES,
RE-
MOVE THE POWER
SUPPLY CORD
GROUND
PRONG.
Converting
to built-in
14
Advertisement
Table of Contents
