Service Mode - Roland VersaCamm VS-640i Service Notes

4-1 SERVICE MODE

+ POWER ON
SERVICE MENU PRINT MENU
PRINT MENU HEAD RANK
PRINT MENU
HEAD ADJUST
PRINT
LINEAR ENCODER
PRINT
LINEAR CHECK
PRINT
LINEAR CALIB.
PRINT MENU
CALIB.DEFAULT
PRINT MENU
TEST PATTERN
PRINT MENU
FLUSHING ADJ.
This is for adjusting the flushing position. Set the head height to LOW. As entering the menu, the Head Carriage moves to the current flushing position.
With [left] and [right] keys, Move the Head Carriage to the position where the slot of the Carriage Cap Guide makes contact with the tip of the Backup Cap Base, and press [ENTER] key to save
the position. Or, start the adjustment from the leftmost position and press [ENTER] key to save the position where arm part of cap unit starts to move.
As [ENTER] key is pressed, the head is automatically capped and it backs out the menu. For backing out the menu without saving the position, press [MENU] key without pressing [ENTER] key.
SERVICE MENU I/S MENU
I/S MENU I/S CHECK
MENU
[ MENU ] key
SERVICE MENU
HEAD RANK
12345678 (1/3)
HEAD ADJUST
BIAS
HEAD ADJUST
BI-DIR.DEFAULT
Dot pattern can be selected with [
[ENTER] key for saving the setting. The value being selected is marked with an under bar.
It returns to the former menu after setting.
Default: 0) It can be changed starting from the standard value (15 from No.1 to No. 4, 27.5 from No.5 to No.8) with [
(
* *
Range: 0 to +60dot (changeable by 0.5dot which is indicated as 1/2.
MENU NOW PROCESSING..
POS: 1361.00mm
MENU NOW PROCESSING..
MENU
NOW PROCESSING..
CALIB.DEFAULT
TEST PRINT
CALIB.DEFAULT
TEST PRINT2
CALIB.DEFAULT
SETTING
TEST PATTERN
BI-DIR.
TEST PATTERN
FILL
TEST PATTERN
BI-DIR. CHECK
NOW PROCESSING..
MOVE CARRIAGE
TO AVOID WIPER
This is for checking the operation of the wiper motor and sensor.
Make sure not to have the Head Carriage and Tool Carriage above the wiper unit during the check.
This menu is used for entering the Head Rank for each head with 24 digit number and alphabet.
The digits can be changed with [ ] and [
[ ] and [ ] keys. The digit being changed is marked with an under bar.
Press [ENTER] key to save the settings. It beeps for alerting when the calculation for verification,
CHECK SUM, is not correct in order to avoid input error.
BIAS PERFORMING
TEST PRINT
Feeds media for visual check of the test pattern, by pressing
[
BIAS
pressing [
to the original position.
--- VIEW ---
BI-DIR.DEFAULT
PERFORMING
TEST PRINT
Ink type : PIGMENT
BI-DIR.DEFAULT No.1
SETTING 15
Ink type : MAX
No.1
15
] and [ ] keys, and value can be selected with [
Normal (beeps 1 time)
LINEAR ENCODER
SETUP COMPLETED
Error (beeps 2 times)
LINEAR ENCODER
Error is found on Linear
Encoder and Scale.
SETUP FAILED
Error (beeps 2 times)
LINEAR ENCODER
Error is found on Head
Board.
HEADBOARD FAILED
Normal (beeps 1 time)
LINEAR CHECK
COMPLETED
Error (beeps 3 times)
Dusts, greases or scratches
LINEAR CHECK
are found on Linear Scale.
FAILED:1000.00mm
Normal (beeps 1 time)
LINEAR CALIB.
SETUP COMPLETED
LINEAR CALIB.
0.18%
Error (beeps 2 times)
LINEAR CALIB.
FAILED TO SETUP
PERFORMING
This menu is used for Calibration.
TEST PRINT Refer to [4-10 CALIBRATION].
PERFORMING
TEST PRINT
When it shows [
SETTING
it needs to be set. In this case, even if adjustment is unnecessary
+0.05% +0.10%
by the test result, [0] must be set here.
PERFORMING
This is for checking the Head Alignment in Bidirectional.
TEST PRINT
PERFORMING
It prints on the entire print range with solid single color by each head.
Print mode is fixed at 720 dpi and 8 pass.
TEST PRINT
PERFORMING
This print pattern is for checking a shifting error in Bidirectional and
also for confirming the mechanical tendency.
TEST PRINT
FLUSHING ADJ.
NOW PROCESSING..
0.00mm -0.40mm
NOW PROCESSING..
Checking
4-2
] keys and parameters can be changed with
TEST PRINT
] or [ ] keys while in [TEST PRINT] menu. Also by
] or [ ] keys again after feeding, media returns
TEST PRINT
No.2 No.3 No.4
20 15
No.2 No.7
20 15
] and [ ] keys.
] and [
This is for checking the installation and
operation of Linear Encoder and Scale.
Refer to [4-5 LINEAR ENCODER SETUP].
This is for checking if there are dusts,
greases or scratches on Linear Encorder.
This is for calibrating the cutting size in the scan direction
by calculating the expansion and contraction amount of the
Encoder Scale.
], it means that it has never been setup and
*****
I/S CHECK
COMPLETED
Error
I/S CHECK ERROR
WIPER
20
No.8
20
] keys.