Advertisement
Before you start.. .
Proper installation
is your responsibility,
Make sure you have everything
necessary
for correct
installation.
It is the responsibility
of the customer
to contact
a qualified
installer to
assure that the plumbing
and
electrical
installations
are adequate
and meet all national
and local codes
and ordinances
Proper eiectncal,
drain and water
supply lines must be avai!able
or must
be installed
as specified
within shaded
area.
See Electrical,
Water and Drain
requirements
Plumbing
and wiring
should not cross In front of motor or
dishwasher
legs.
Check
location
where dishwasher
will
be installed.
The location
should
provide:
l
Easy
access to water,
electricity
and drainage
lines.
l
Convenient
loading
- the best
position
is left or right of kitcnen
sink.
l
Opening
that is square for proper
dishwasher
operation
and
appearance.
l
Cabinet
front that is perpendicular
to floor.
l
Protection
so that water
inlet valve
and drain cannot
freeze.
l
l/4" minimum
ciearance
between
motor and flooring
to prevent
the
motor from overheating.
corner
location
2" min. door to
cabinet
or wall
IMPORTANT: Observe
all
governing
codes
and
ordinances.
L
24",
Water line
l/2"
hole or larger.
Drain line
1 l/2"
hole or lalger.
'S~""F"
I",
electrical
cable
hole
(metal
cabinets)
Electrical
line I /2"
hole cr larger.
Electrical
ground
I$ rPc-71 Ilr@d
SPP
- .- -l-L"-
-' -- -
Elect:ical
requirements.
The unshaded
area must be free
of pipes or wires.
24" opening
Electrical
Shock Hazard
l
Electrical
wiring and
components
must not contact
any plumbing
material
or drain
hose.
l
Cabinet
opening
must
completely
enclose
sides, top
and back of dishwasher.
Failure to do so may result in
personal
injury from exposti
wiring.
Do Not Install dishwasher
width
-
Figure 1
over carpeted
flooring.
i-
24" depth
-
7'.
I/
I
II
Side view
33-7/a"
min.
helghi
Personal Injury/Product
Damage
Avoid opening
dishwasher
door
before dishwasher
is installed.
Dishwasher,
before it is installed,
may tip over when door is opened
resulting
in personal
injury or
product
darnone
Read and follow the "Electrical
requirements",
"Water
requirements"
and "Drain requirements"
connection
j?ctlons
before
nsralilng
dlsnwasher
Figure 2
-
20-314"
Tools
needed for
Electrical
requirements
A
120-volt, 60 Hz,
AC only, 15 or 20-
ampere, fused, electrical supply is
required.
Time-delay fuse or circuit
breaker is recommended.
It is
recommended
that a separate
circuit serving only this appliance
be
provided.
It is the personal responsibility and
obligation
of the customer to
contact
a qualified electrician
to
assure that the electrical installation
is adequate
and in conformance
with the National Electrical Code,
ANSI/NFPA 70- latest edition, and all
local codes and ordinances,
The dishwasher must be connected
with copper wire only.
installation:
Electrical
Shock Hazard
.Electrical
ground
is required
on
this appliance.
Check with a
qualified
electrician
if you are
in doubt as to whether
the
appliance
is properly
grounded.
mproper
connection
of the
equipment-grounding
conductor
can result in electrical
shock.
l
Disconnect
power to the
junction
box.
Failure to do so could
result in
serious injury or death.
*This appliance
must be
connected
to a grounded,
metallic
permanent
wiring
system, or a grounding
connector
should be connected
to the grounding
terminal
or wire
lead on the appliance.
Failure to do so could result in
serious injury or death.
*Do Not have a fuse in the neutral
or grounding
circuit.
This could
result in electrical
shock.
l
Do Not use an extension
cord
with this appliance.
Such use may result in a fire,
electrical
shock or other personal
injury.
Wiring methods
electric
drill
Phillips
screwdriver
2 adjustable
wrenches
flat-blade
screwdriver
measuring
tape
pliers
pipe wrench
keyhole
saw
tubing cutter
(not shown)
pipe-joint
compound
wire stripper
and
utility knife
5116 and l/A inch
nut driver or hex socket
Pick one method to follow
depending
upon your dishwasher
and local codes.
A
Direct wire method
(cdble
connecting
dishwasher
to a junction
box)
;Tt;;mended
grounding
1.
Disconnect the power supply.
Parts sup lied
for instal P ation:
l
2, drain hose
clamps
l
drain hose
12, No. 10 x l/2"
Phillips-head
screws
Panel A
Advertisement
