Advertisement
Before you start . . .
Proper rnsiallation IS your responsibility
Make we you hove everyihing
necessary for correct Instollol~on It 1s the
personal responsibility end obllgatlon
of
the customer to contact
o quaIlfled
Installer to assure that electrlcol
ond
plumbing ~nstollal~on mecl nal~onai and
local codes and ordlnonces
IMPORTANT:
Observe
all
governing
codes and
ordinances.
DO NOT install dishwasher
over carpeted
floor
Proper eleclrlcol.
dram and water
SUPPIV
lines must be available
or must
be lnslallcd as speclfled wllhin shaded
Oreo
See Electrrcal. Water and Droln
requrrements.
Plumbing and wiring
should not cross In front of motor or
drshwoshcr legs
If plumbing ond electrrcal
connecllsns
ore not installed. complete
the
Electrical. Waler and Drain Connectrons
Installation InstructIons frrst.
ElectrIcal ground
-
is reauired
See
Elecirrcal requirements
Parts supplied
Electrical
for installation:
requirements
Remove
parts from bag. Check
that all parts were supplied.
Tools needed
for fnstallation:
Electrical Shock Hazard
*Electrical
ground is required on
this OrJoliance.
Check with (I
qualiiied
electrician
S you are in
doubt as to whether the
appliance
Is property grounded.
Improper connection
of the
equipment-grounding
conductor
con result in dectrical
shock.
*Disconnect
power to the junction
box.
Failure to do 50 could result in
serious injury or deoih.
*This appliance
must be
connected
to a grounded,
metallic
permanent
wirina
system. or a grounding
-
connector
should be connected
to the grounding
terminal or wire
lead on the appliance.
Failure to do so could result in
serious injury or death.
l
Do Not have a fuse in the neutral
or grounding
circuit.
lhhcckquld result in electrical
*DO Not use an extension
cord
with this appliance.
Such use may resull in a fire,
electrical
shock or otner personal
injury.
Check locatron where dlshwasher WIII
be installed. The location
should
provide:
l
Easy access to water. electricity
and drarnoge
lines
. Convenient
loadrng - the best
pos11ron IS left or rrght of kitchen sink.
. Openrng that is square for proper
dishwasher operahon
and
appearance.
l
Cabinet
front that IS oeroendiculor
to floor
l
Protection
so that water inlet valve
and drain cannot freeze.
. l/4" minimum clearance
between
motor ond flooring to prevent
motor overheating.
Electrical Shack Hazard
l
Electrical wiring and
~~ -1
components
must not contact
any plumbing
material or drain
hose.
l
Cabinet opening
must
completely
enclose sides, top
and bock of dishwasher.
Failure to do so may result in
personal injury from exposed
wiring.
Personal Injury
Avoid opening dishwasher
door
before dishwcsher
is installed.
Dishwasher. betore il is inslolled
may tip over when door is o&n&d
resulting in personal injury or
product damage.
,
A I P~volt. 60 Hz. AC only. 15 or 20
ampere,
fused electrical
supply Is
required.
Time-delay
fuse or clrcutt
breaker is recommended.
lt ls
recommended
that a separate
circuit serving
only this
appliance
be
provided.
It ls the personal responsibilii
and
obligation
of the customer to
con&t
a qualmd
electdclan
ta
assure that the elect&al
installation
Is adequate
ond Is in conformance
with the National Electdcal Code,
ANSVNFPA 7@!~test editlon. and
local codes and ordinances.
The dishwasher can be connected
with flexible armored
or non-metallic
sheathed
copper
cable (with
groundlng
wire).
A U.L.-listed strain relief or conduit
connector
must be installed ot each
end of the Dower SUDDIV cable tat
the dishwajher
and bi {he junction
box). Wire sizes (COPPER WIRE
ONLV) must conform
with the rating
of the dishwasher.
Local codes may permtt the use of a
U.L.-listed. flexible three-conductor
l&gauge
cord terminated
with a
three prong. grounding
type plug.
The cord must meet the National
ElectrIcal Code. ANSl/NFPA 7C-lotest
edttton and local codes and
ordlnonces.
The length of the cord
must not exceed
six feet. It must be
routed
so it does not touch the
dishwosher motor or the lower
portion of the dishwasher tub. A
grommet
(Part No. 302797) must
cover the hole cut In a metol
cabinet
for the flexible cord. The
flexible cord must be plugged
into a
mating three-prong
grounding
type
wall receptcle.
Follow Instructions
packaged
with the flexible cord.
Panel A
Advertisement
