ADEMCO 4150 C-COM Installation Instructions Manual page 3

.
opening and closing reports, might be routed to,a secondary, :
receiver.
l Prlrnary Phone Number Asslpnmont
Fire, Zone 2 Alarm, Zone 3 Alarm, Zone 4 Alarm, Zone 5 Alarm,
Zone 6 Alarm. Zone 7 (EMEAG Keys) Alarm and Cancel.
l
Seoondary Phone Numkr Anlgnment
Open, Close. Restore, Low Battery, Trouble, Test, Bypass
It is possible to PROM select. by specific report. which reports are
desired to be sent to the other phone number too (e.g. Restore).
3. Communtcatot Code Mgnmsnl
Each alarm zone in the system may be assigned its own
communicator code. How the zones are assigned to codes affects
the reports that wilt be sent. As an example, each zone could be
given a dierent communicator code for unique zone reporting. Gr
the zones could be grouped by function with duress/silent
panic (common rep&ting code) zones as Code 2, the fire zone as
Code 1, and the burglary zones as Code 3 (this would allow the
system lo be compatible with an existing central station alarm code
scheme).
4. Communlator Format
Individually selectable for primav and secondary telephone numbers
- Ademco Low Speed or SESCOA/Radionics.
2. ZONE RESTORE/SWINGER SHUTDOWN
.&rce a zone is faulted, it will be re-enabled for local alarm sounding at
timeout or whenever if becomes intact, whichever is later. n will be re-
enabled for central station reporting only after it has remained intact for
at least l-2 minutes. A restore message will be sent. if PROM enabled. to
- the central station al this time.
NOTI? If two or more zones are PROM assigned the same alarm
reporting code, then multiple restores using this code will bs
transmkted.
The 1 minute communicator disable, in conjunction with automatic
shutdown of a zone after it reports 3 alarms within a single armed
period. is intended to prevent annoyance calls to the central station for
swinging zones. The shutdown of the zone is accomplished by
automatic bypass of the zone after the 3rd alarm report, indicated by
the BYPASS LED lighting steadily.
central station reporting for fire and panic alarms will be re-enabled
l-2
minute5 after a security code is entered to silence these types of alarms
(provided that zone is not fautted during the l-2 minute period).
II. FUNCTIONAL DESCRIPTION, No. 4156 REMOTE
KEYPAD (See Diagram 4)
A KEYPAO and LEDs
Keys o-9: These are used to enter the arm/disarm security code(s)
and the duress code.
STAY Kay and LED (YeBow): When depressed subsequent to
depression of the CMND Key in lhe disarmed state. shunts fhe
fnterior burglary zone. The STAY LED is fii then and remains lii when
the system is armed. This LED also has a secondarv desionation as
the Zone 2 LED. When the ZONE DISPLAY key is held deiressed,
this LED indicates the state of Zone 2. providing current violation
status (on steady) as well as memory of alarm [flashing). The latter
is not cleared until me system is next armed.
POWER LED (Oman): This LED indicates the presence of AC
power to operate the system. The LED will immediately flash when
AC power is lost and the system is operating from its standby
battery.
This LED also has a secondary designation as the Zone 6 LED.
When the ZONE DISPLAY key is held depressed. this LED is on
steady for current violation and flashes for memory of alarm on
Zone 6. Tha latter indication is not cleared until fhe system is next
armad.
BYPASS Kay and LED (yellow): Depression of the CMND and
BYPASS keys causes the system to enter fhe bypass moda. While in
this mode. the BYPASS LED will flash as confirmation that me mode
is in effect. A flashing zone LED indicates that a zone is faufted and
not yet shunted while a steadily Iii LED indicates brat a zone is
shunted. A zone may be shunted or unshunted by depressing the
key corresponding to its zone number. Note that zones may be
shunted only while the system is disarmed and that 24 hour zone5
may not be shunted.
The bypass mode is exited by depressing the CMND key. The
bypass mode will be exited automatically if no key is depressed for
a1 feast 30 seconds. Once me mode is exited. the BYPASS LED will
ba on steady U one or more zones were shunted. Note that all
shunts are removed automatically when the system is disarmed.
.
A bypass report is hansmined along wfth a closing report-(if PROM
enabled) at arm time if one or more zones were shunted. A bypass
restore report is transmitted along with an opening report (if PROM
enabled) at disarm time if any shunts were in effect.
lNSTANT Key and LED (YeSow): When depressed subsequent to
entry of the security code and the CMND key. the burglary system
will arm with the entry delay disabled on the entry/exit and interior
zones. making them instant alarm zones tor subsequent entry. The
INSTANT LED is lit when me system is in this mode. The entry delay
for these zones is restored subsequent to the system being
disarmed. This LED also has a secondary designation as the Zone 5
LED. When the ZONE DISPLAY key is held depressed this LED is
on steady for current violation and flashes for memory of alarm on
Zone 5. The latter indication is not cleared until the system is next
armed.
CODE Koyz When depressed prior to entry of the master security
code, will permit the immediate (within 10 seconds after master
code entry) entry of a code designation (1.2. or 3) and a secondary
user changeable 4 digit security code. The code designation of 3 is
used for entry of the duress code. The duress code permits the
performance of all of the functions of the master code exceot
secondary code change. The other secondary codes permit the
performance of all of the functions permitted by the PROM
programmed master code except secondary &de change.
Repeating digits are permitfed in code entries.
CHIME Key: When depressed subsequent to depression of the
CMND Key during the disarmed state. will cause entry to a mode
where any fault in the Entry/Exii Burglary Zone will cause a brief
loud tone to ba heard at each remote keypad. The mode can be left
by subsequent redepression of the CMND and CHIME keys. The
CHIME mode is in effect during the armed state but is not heard
because the entry delay warning sound overrides the other sound.
READY LED (Qraea): The READY LED is lit whenever all burglary
zones are intact (ready for arming) during the disarmed state. It is off
whenever a zone fault is present. This LED flashes as a memory of
alarm indication (along with the ARM LED) in the armed state for
audible alarms. This memory of alarm indication is removed by entry
of the security code. This LED also has a secondary designation as
the ZONE 3 LED. When the ZONE DISPLAY key is held depressed,
this LED is on steady for current violation and flashes for memory of
alarm on Zone 3. The latter indication is not cleared until the system
is next armed.
flRE and FIRE Kom Simuttaneous depression of both keys
causes manual activation of the fire alarm (if PROM enabled).
EYERG and EYERG Koyr: Simultaneous depression of both keys
causes manual activation of a Panic Zone alarm (audible or silent
as a function of zone programming) or no action (dependent upon
programming).
TROUBLE LED (RED): If one or more of the following conditions
has occurred, the TROUBLE LED will be lit steadily and an audible
trouble signal (short beep) will be heard every 15 seconds:
(1) An opan circuit occurs in me fire zone.
(2) A security code is entered subsequent to a fire or panic zone
. violation and the zone is still violated.
If one or more of the following conditions has occurred. the
TROUBLE LED will flash and no audible trouble signal will be heard:
(1) The fire circuit fails to reset following the silencing of a fire alarm
using the TEST/RESET command (see below).
(2) The fire zone remains faulted after the fire alarm has timed out (if
time out is PROM enabled).
(3) The audible trouble signal is silenced using the TEST/RESET
command but steady LED and intermittent beep may return after 24
hours if the condiiion remains. (see below).
The TROUBLE LED will turn off as soon as the condkion that
caused it to be lit is eliminated.
This LED also has a secondary designation as fhe Zone 4 LED.
When the ZONE DISPLAY key is hetd depressed, this LED is on
steady for current violation and flashes for memory of alarm
Zone 4. The latter indication is not cleared until the system is
next armed.
3