Installation And Wiring - ADEMCO 4150 C-COM Installation Instructions Manual

.
1. Setem from O-9.6-F (not 8)
2. Central station reporting of any of these codes can be disabled lf
the report ~~~~~~k~progranVned)
3-
15: ADDlTtONAL ROUTING OF REPORtS TO SECONDARY
NUMBER (hex.)
LOCATION 060
Se.tsct if it Is desired to &ae route these Atan Reports to the Secondary
Phone Number (Dual Report). Do not select othen&e.
Bn vahm
Rm
1 i!Onel
2 zone 2
4 zone 3
8 Zone 4
MdhOVdUOSSdOOtOd
Enmr Bn
vduw Bdootod
convert to hex.
18. ADDITIONAL ROWING OF REPORTS TO SECONDARY
NUMBER (hex.)
LOCATION 061
Enter 811
Bn value
RW
vduw somcmd
1
zone 5
2
Zone6
4
Zone 7 Oawote Emgy Keys)
8 Cancel
AddlhSVdUWBOkObd
convert to hex.
17. ADDITIONAL ROUTlNG OF REPORTS TO PRIMARY NUMBER
(hex.1
LOCATION 062
Enter Bn
Bn v8hn
Rm
Vdws Bamomd
1
OF
2 uose
4 Restore
8
Low Battery
MdthOVdW8BObCtd
convert to hex.
18. ADDtTlONAL ROUTING OF REPORT TO PRIMARY NUMBER
AND B4 HOUR TEST REPORT ENABLE (hex.)
LOCATION 063
Enter BH
Bn wua
R.P-l
VOlUWBdWtOd
1
BYP=
2 Tmubfe
4 Test
8 Bomotlf8umnmtb
24 hour Test Report is dealred
(00 not aeleot otherwise).
Md#OVOlUWBObOlOd
convwl to hex.
19. ZONE lVPE SELECTION
1
Lo&ton
Zone 2 064
EiEl--
*n
Cl65 - ".
!
Zone 3
Zone 4
-066
Zone 5
067
Zone 6 068
Zone 7
069
Select trom the tollowmg types:
U = No Action
1 = Audibte Panic
2 = Sitent Panic
3 = Entry/Exit Burglary
4 = Perimeter Burglary
5 = Interior Burglary
Notm Zone 7 is activated by the Console EMERG Keys and by the
Duress Code.
NOTEz In udng the NAPCO PRO.410 Pm@mmwr, make sure tlmi
addrow loatiolw 070 and 071 are skippod bhre the next
code8 we ptoqmmmed.
20. REPORTING CODES (GROUP 3)
Zone 7 Alarm
BYWSS
1 Code 1 Lo$ion
NOTES: 1. Select from O-9. B-F (not I)
2. Central station reporting of any of these codes can be disabled
if the reporting code is left blank (i.e. unprogrammed)
21. BEBCOA FIXED INTERDlGlT FORMAT SELECTION
LOCATION Ct80
f-?
Do not select tf is desired to communicate in SESCOAlRadionics format to,
newer (post 1981) SESCOA receivers or to Radionics receivers. Select for ',
'
older (1981 and earlier) SESCOA receivers.
Enter Bit
Bn Vdw
valuw semctod
1 Not Used
. . . . . . . . . .
2
Primary Telco No.
4 Secondary Telco No.
8
Not Used
. . . . . . . . . .
AddlhOVdWSS8bOld
convert to hex.
VI. INSTALLATION AND WIRING
A. INSTAUATlON AND WIRING, NO. 4150 C-COM
To insure proper system checkout with a charged battery. connect
me battery to the red and black wires on the control's circuit board
and then connect the transfwmer to the control and to a 11 OV outlet
(see Diagram 5). Contml need not be mounted but shoutd be grounded.
Do not insert PROMS or connect console at this time. Battery will
charge while me installation is being wired. REMOVE ALL POWER, AC
AND BATTERY. BEFORE CONNECTIONS ARE MADE TO CONTROL
TERMINALS as instructed below. Uw ot twbtod wlrtng b recom-
mended for all runs, for greater immunity to unwanted induced
vo)tageS.
=RWlNALS (See Diagram 5)
TBl
Clroult Ground (-) Return
12 Voll Contlnuow power (+) lor Poworlng Remote
Koypods This terminal is one of the four wire connection points
(RED) for remote keypads. The current drain from the terminal
must not exceed 25CtmA (see SPECIFICATIONS).
Cimull Ground (-) Roturn: This termtnal is one of the four wire
connection points (BLACK) for remote keypads.
10