ADEMCO 4150 C-COM Installation Instructions Manual page 11

I
4
Keypod Clock Outpub This terminal is one of the four wire
The zone has a notmaf (200 MSEC) mponae lo open and
connection points (GREEN) for r&mote keypads and controls the
flow of data lo and from th&e units.
closed circuit devices such as magnetic or mechanical
contacts.
5
Keypad Dete Input/Output: This terminal is one of the four
wire connection points (YELLOW) for remole keypads. Data
entered at the keypads is fed into the G-COM a1 this terminal
and data led back lo LED6 and audible warning sounders al the
keypads is routed out tram this terminal.
6(+)
8V.DC' or 12V.DC Power tar Smoke (BRK Nox. BK-2806.
12(+).
7(-)
BK28WTH. 811-2812, BK-2812TH) or Comb&Won (BK-1806
13(-1
or BK-1812) Deteotore (interruptible by the TEST/RESET key
on the remote keypad). Obsewe polarity. Use wire sizes in
accordance with the follwring tabulation and connect the power
terminals of the detectors in parallel:
The current drain from these terminals must not exceed 250mA
(see SPECIFICATIONS).
Maximum permissible resistance in the zone: 600 ohms (Plus
2000 ohm End-of-Line Resistor).
This zone is PROM programmable for either.a;dible or silent 24
hour panic alam or for entry/exit. perimeter. or interior burglary.
Zone 5: Run a pair of wires from the zone terminals to all pro-
tectiin points in the zone and terminate with a 2000 ohm End-of-
Line Resistor (supplied).
'Cut RED jumper for 6V selection.
The zone has a normel (200 MSEC) mponse to open and
closed circuit devices such as magnetic or mechanical con-
tacts. foil. piezo-electric glass break sensors, etc. or laal(l5
MSEC) response to faSt acting (normally closed) devices, such
as glass break or vibration (e.g. No. 11) sensors (cut jumper
selectable for fast response - WHITE jumper).
Maximum permissible resistance in the zone: 600 ohms (plus
2000 ohm End-of-Line Resistor).
This zone is PROM programmable for either audible or silent 24
hour panic alarm or tar entry/exit. perimeter. or interior burglary.
Zone 8: Run a pair of wires from the zone terminals to all pro-
tection points in the zone and terminate with a 2000 ohm End-of-
Line Resistor (supplied).
"Use separate power runs for up lo 6 detectors each.
CAUTION: Do not UM Pyrotector Phoenlx Serb xmoke detectors
7(-J
Clroult Ground (-) Return: Connect this terminal 10 a good
earth ground (cold water pipe or electrical box ground is
frequently satisfactory for this usage, but in some locales is not).
Thb connection b orltioel to enhancing the immunity of the
The zone has a normel (200 MSEC) mponaa to open and
closed circuit devices such as magnetic or mechanical
contacts. mats. motion detectors. etc.
Maximum permissible resistance in the zone: 600 ohms (plus
2000 ohm End-of Line Resistor).
This zone is PROM programmable for eilher audible or silent 24
hour panic alarm or for entry/exit. perimeter. or interior burglary.
system 10 unwanted mduceo transients ~llgntnmg ana
electrostallc discharge).
Tenlnab
7(-),
Zone 1 (Fire Protection Zone): Run the supervised fire de&-
'
W+)
tion loop from these two terminals to all U.L. Listed thermostats.
smoke detectors. combustion detectors or other detection
a+),
devices to be used. Runs of up to 500 feet may be made with
3(-j
#20 wire. Run one continuous loop (no branches) through all
devices, connecting any trouble relay contacts in series with the
loop and normally open alarm contacts across the loop's two
wires. At the last device, terminate the loop with the furnished
2000 ohm End-of-Line Resistor and a No. BK-A77716OOf BK-
4.5
A7771 601 Supervisory Module, as shown in the instructions with
the smoke or combustion detector. Maximum permissible
resistance in the zone is 600 ohms (plus the 2000 ohm End-of-
Line Resistor). The tire zone will detect trouble for an open in the
W-1.
zone and alarm for a shorl across the zone. A separate keypad
LED annunciates a fire trouble.
7(+)
NOTEZ Low currenl smoke and/or combustion detectors such
as the BRK Nos. BK-2806. BK-2806TH. BK-2812. BK-
2612TH. SK-1806 or BK-1812 should be used. NFPA
Standard No. 74 requires the use of at least one smoke
or combustion detector in every residential installation.
91+1. Zone 2 Conned ooen circuil momentary switches fe.a. Nos.
Clrmlt Grwnd (-) Return:
, .
lo(-)
219.273.4024.4Oi6) or contacts in par&let across ih&e
8
terminals. The zone is PROM programmable for either audible or
silent 24 hour panic alarm or for &try/exit, perimeter. or interior
burglary.
IO(-).
ll(+)
Zone 3: Run a pair of wires from the zone terminals to all closed
9
circuit (N.C.) protection points in the zone and terminate the loop
with the tumished 2000 ohm End-of-Line Resistor. Thii
termination is required even i! these terminals are only used for
connection of open circuit momentary switches or contacts.
10
Maximum permissible resistance in the zone is 600 ohms (plus
the 2OUO ohm End-of-Line Resistor). This zone has a nomul n-
sponse (200 msec) to closed circuit devices such as magnetic
or mechanical contacts, foil, piezo-electric glass break sensors.
11.12
etc.
This zone is PROM programmable for either audible or silent 24
hour panic alarm or for entry/exit, perimeter or interior burglary.
13.14
Zone & Run a pair of wires from the zone terminals to all pro-
tection points in the zone and terminate with a 2000 ohm End-of-
Line Resistor (supplied).
11
Alarm Boll Vottrga: These terminals provide 6 or 12V.DC (cut
RED jumper for 6V selection) during an audible alarm. This
output is steady for burglary and audible panic and pulses for
fire. (See SPECIFICATIONS for current drain.)
NOTE: This output will be produced in both the Burglary System
Test and the Fiie Test Modes.
Power Input, 18V.AC: Connect these terminals lo the
secondary output terminals of the No. 1349,40 VA Transformer.
Do not plug In the Tmnrtonner yet, or oonneot the bettery.
Contlnuoue 8 or 12V.DC (cut RED jumper for 6V selection)
Auxllbry Power tor Aooeuorleez Observe polerlty. These
terminals provide power for accessories such as space
protection devices, e.g. ultrasonic or passive infrared detectors.
photoelectric.% etc. Devices connected to these lenninals should
be UL Listed and (when outpul is programmed for 12V.DC)
should be rated for operation a( 13.5V.DC.
The current drain from these terminals must not exceed 350 mA
(See SPECIFICATIONS).
Armlobamt Status Output (LO= Armed, HI =Dbormed): This
output provides a voltage that can be used for miscellaneous
control functions. The maximum output from this terminal is
12V.DC with a 2K Ohm current limiting resistor.
Amrlohartn Status Output (HI= &mod. LO =Dtumwd): This
output provides a voltage that can be used for miscellaneous
control functions. The maximum output from this terminal is
12V.DC with a 2K Ohm current limiting resistor.
DWer Act&e Output (HI = Active): This output provides a
maximum of IPV.DC through a 1 K Ohm current limiting resistor
while the line seize relay is activated. It can be used lo activate a
remote LED indicating thal communication is underway.
Intemel Hmddsats~ Connect T62-11 to the BROWN lead and
TB2-12 10 the GRAY lead on 'he No. 620 RJ31 X Direct
Connect Cord.
lncomlna Teloo Urn Pair. tinnecl TB2-13 lo the RED lead
and T62-i 4 to the GREEN lead on the No. 620 RJ31 X Direct
Connect Cord. Do not oonneot the latter cord to the RJSIX
Jack until all wiring in me system has been completed.
'.