Related Manuals for Axminster Trade AT406SS
Summary of Contents for Axminster Trade AT406SS
- Page 1 AT406SS Code 101771 AT535SS Code 101772 AT762SS Code 101773 Original Instructions AT406SS, AT535SS, AT762SS Scroll Saws AT406SS (KC-16) AT535SS (KC-21) AT762SS AT&M: 18/03/2020 (KC-30) BOOK REF: 101814 BOOK VERSION: 2...
-
Page 2: Eu Declaration Of Conformity
EN 61029-1:2009+A11 Type Scroll Saw Model AT406SS, AT535SS, AT762SS and conforms to the machinery example for which the EC Type-Examination Certificate No AM 50328372 has been issued by The Kingcraft Machinery Co., Ltd. Signed at: No. 26, Gong Yeh 12 Road, 41280 Dah Li Dist., Taichung City Taiwan and complies with the relevant essential health and safety requirements. -
Page 3: Rules For Safe Operation
Rules for Safe Operation To help ensure safe operation, please take a moment to learn the machine’s applications and limitations, as well as potential hazards. Axminster Tool Centre disclaims any real or implied warranty and holds itself harmless for any injury that may result from the improper use of its equipment. -
Page 4: Safety Instructions
Safety Instructions... -
Page 5: Electrical Requirements
Electrical Requirements... -
Page 6: Identification Of Main Parts & Components
Identification of Main Parts & Components ON/OFF Switch (A) Speed Control Dial (B) AT535SS NVR power isolating switch... -
Page 7: Unpacking And Setup
Unpacking & Set Up AT535SS (KC-21) AT762SS (KC-30) AT406SS (KC-16) Installation & Assembly... -
Page 8: Choosing & Installing A Saw Blade
Installation & Assembly Saw guard assembly Slot the guard clamping arm (d) through the pre-drilled hole in the hexagon clamp (c). Insert the hexagon clamp (c) into the brackets hexagon recess, place the washer (b) over the hexagon clamp thread and secure using the butterfly clamping knob (a). - Page 9 Choosing & Installing a Saw Blade...
- Page 10 Choosing & Installing a Saw Blade Operating Instructions...
- Page 11 Operating Instructions Adjusting the Osolation (Front to Back) Top & Bottom Blade holder Alignment Fig A Fig B Fig A Fig B Fig C Fig D Fig C Fig D Place a 90˚ square upagainst the blade, the blade movement If the blade is out of alignment please follow the procedures below for can be set between course and fine for different cutting tasks, adjusting the top and bottom blade holders:...
- Page 12 Operating Instructions...
- Page 13 Operating Instructions...
-
Page 14: Maintenance, Adjustments & Servicing
Maintenance, Adjustments & Servicing... -
Page 15: Changing The Fuse
2. Unscrew the fuse cap to the rear of the scroll saw 4. Re-insert the fuse assembly and finger tighten. and remove the 5 AMP fuse. Specifications Code 101771 101772 101773 Model AT406SS (KC-16) AT535SS (KC-21) AT762SS (KC-30) Rating Trade Trade Trade Power 230V 50Hz 320W... -
Page 16: Optional Accessories
Optional Accessories Foot Switch with Trailing Plug & Socket These two foot-operated safety switches are equipped with trailing plugs and sockets and can easily be inserted between the mains supply and any machine fitted with a no volt release switch, such as a drill, bandsaw or lathe. - Page 17 Stand Assembly Step 3 Step 7 Use the holes in the bracket to adjust the stand height Step 4 Stand assembled Step 5 Lower the scroll saw on top of the stand and lineup the holes, secure using the four bolts washers and Nuts Step 6...
- Page 18 Exploded Diagrams/Lists KC-16 - KC-21 - KC-30 Diagram A...
-
Page 19: Specification
Exploded Diagrams/Lists KC-16 - KC-21 - KC-30 Diagram A REF. PART NO. DESCRIPTION SPECIFICATION EX21-A55 Label EX21-A01 Main Body EX21-A56 Screw 1/4*2-1/2 EX16-A78 Main Body EX21-A57 Upper Arm EX30-A01 Main Body EX16-A80 Upper Arm EX21-A03N Top Cover EX30-A57 Upper Arm EX16-A79 Top Cover EX21-A58... - Page 20 Exploded Diagrams/Lists KC-16 - KC-21 - KC-30 Diagram B...
- Page 21 Exploded Diagrams/Lists KC-16 - KC-21 - KC-30 Diagram B REF. PART NO. DESCRIPTION SPECIFICATION EX21-B24 Spring EX21-B01 Trunnion EX21-B25 Detent Plunger EX21-B02 Side Panel EX21-B26 Tilt Handle EX16-B41 Side Panel EX21-B27 Washer 1/4x16x3 EX30-B02 Side Panel EX21-B28 Blade Tilt Locking Lever EX21-B03 Rear Trunnion Plate...
- Page 22 Exploded Diagrams/Lists KC-16 - KC-21 - KC-30 Diagram C...
- Page 23 Exploded Diagrams/Lists KC-16 - KC-21 - KC-30 Diagram C REF. PART NO. DESCRIPTION SPECIFICATION EX21-C37 Set Screw M6*8 EX21-C02 Balance Block EX21-C38 Blade Clamp Thumb screw EX21-C03 Set Screw M6*6 EX21-C39 Blade EX21-C04 Allen Screw 1/4-20x1/2 EX21-C40 Allen Key EX21-C05 Lock Washer 1/4.
- Page 24 Base Mounting Holes Length Base Hole Dimensions Model Length Width AT406SS (KC-16) 262mm 343mm AT535SS (KC-21) 385mm 343mm AT762SS (KC-30) 615mm 343mm...
-
Page 25: Wiring Diagram
Wiring Diagram... - Page 26 Notes...
- Page 27 Notes...
- Page 28 The Axminster guarantee is available on Craft, Trade, Engineer, Air Tools & CNC Technology Series machines Buy with confidence from Axminster! So sure are we of the quality, we cover all parts and labour free of charge for three years! For more information visit axminstertools.com/3years The packaging is suitable for recycling.
Need help?
Do you have a question about the AT406SS and is the answer not in the manual?
Questions and answers