Related Manuals for Pro-Lift G5ZL
Summary of Contents for Pro-Lift G5ZL
- Page 2 Thank you for purchasing a Pro‐LIFT G5Z. The Pro‐LIFT product line is designed to enhance your interactive whiteboards and projectors or LCD. Please follow all assembly instructions correctly to provide optimal use. Only a qualified contractor should install the Pro‐LIFT G5Z. If you do not understand any of the assembly instructions, please contact your local re‐seller or visit www.proliftstand.com. IMPROPER INSTALLATION CAN CAUSE DAMAGE TO YOUR Pro‐LIFT AND LEAD TO SERIOUS PHYSICAL INJURY. JORO Manufacturing cannot take any responsibility for damage or injury resulting from improper installation. Do not operate Pro‐LIFT G5Z if there are any obstructions below or above the board. Doing so may cause unit malfunction or lead to serious physical injury. The supplied mounting hardware is for use on the Pro‐LIFT stands only. If you encounter any problems or insufficient hardware during installation, please contact your local re‐seller. ...
- Page 3 G5ZL Main Frame Kit V1.0 3/16" Allen (Hex) Key Cable Clamp - 1-1/2" 5/32" Allen (Hex) Key Nylon Cable Clip 5/16'' G5ZL LCD Mount Fastener Kit V1.0 3/16" Allen (Hex) Key Tube End Cap www.joromfg.com www.proliftstand.com COPYRIGHT 2017 ProLift G5ZL ASSY Instructions : 2.002...
- Page 4 1 AIMWCASTER M6 x 14mm Socket Cap Screw Mount the Pro-LIFT G5Z Feet Use the M6 x 14mm Socket Cap Screws provided Do NOT over tighten www.joromfg.com www.proliftstand.com COPYRIGHT 2017 ProLift G5ZL ASSY Instructions : 2.002...
- Page 5 Do NOT over tighten Use the JORO Button Heads provided Repeat for other side Mount the Cable Clamps Use the Thread-Cutting Screw (8-32 x 1/2" Lg.)s provided Do NOT over tighten www.joromfg.com www.proliftstand.com COPYRIGHT 2017 ProLift G5ZL ASSY Instructions : 2.002...
- Page 6 Pro-LIFT LCD ARM G5Z-ACC-LUPR RIGHT 5/16x1" SILVER Button Head Remove the 5/16x1" SILVER Button Head screws and unhook the Pro-LIFT LCD ARM Do NOT misplace the 5/16x1" SILVER Button Head screws www.joromfg.com www.proliftstand.com COPYRIGHT 2017 ProLift G5ZL ASSY Instructions : 2.002...
- Page 7 G5Z-ACC-LUPR RIGHT G5Z-ACC-LUPR LEFT 4 M6 x 14mm Socket Cap Screw G5Z-ACC-LUPR RIGHT Mount the Pro-LIFT G5Z-ACC-LUPR Use the M6 x 14mm Socket Cap Screws supplied Do NOT over tighten www.joromfg.com www.proliftstand.com COPYRIGHT 2017 ProLift G5ZL ASSY Instructions : 2.002...
- Page 8 Use the appropriate fasteners as specified in the LCD owners manual ****NOTE: You may have to use a combination of fasteners and spacers to achieve correct length. You may also have leftover parts. Do NOT over tighten www.joromfg.com www.proliftstand.com COPYRIGHT 2017 ProLift G5ZL ASSY Instructions : 2.002...
- Page 9 1/4" Washer ARM2025 G5ZL-600V Mount the Pro-LIFT LCD Arms to the G5-ACC-PT5 tubes Mount the Pro-LIFT LCD Arms prior to hanging on the Pro-LIFT G5Z main frame Use the fasteners supplied DO NOT COMPLETELY TIGHTEN! Allow for ARM2025 G5ZL-600V alignment www.joromfg.com...
- Page 10 7 G5Z-ACC-LUPR LEFT Angle G5Z-ACC-LUPR LEFT G5Z-ACC-LUPR RIGHT Hang the LCD assembly Be sure to hang on all four (4) pins on angles www.joromfg.com www.proliftstand.com COPYRIGHT 2017 ProLift G5ZL ASSY Instructions : 2.002...
- Page 11 5/16x1" SILVER Button Head 5/16x1" SILVER Button Head 8 Secure Pro-LIFT LCD Arms to G5ZL Uprights (Repeat for other side) Use the 5/16x1" SILVER Button Head Screws that were removed earlier Tighten all 5/16x1" SILVER Button Heads Do NOT over tighten www.joromfg.com...
- Page 12 ...