Subscribe to Our Youtube Channel
Related Manuals for Pro-Lift WMH Series
Summary of Contents for Pro-Lift WMH Series
- Page 2 Thank you for purchasing a Pro‐LIFT WMH. The Pro‐LIFT product line is designed to enhance your interactive whiteboards and projectors or LCD. Please follow all assembly instructions correctly to provide optimal use. Only a qualified contractor should install the Pro‐LIFT WMH. If you do not understand any of the assembly instructions, please contact your local re‐seller or visit www.proliftstand.com. IMPROPER INSTALLATION CAN CAUSE DAMAGE TO YOUR Pro‐LIFT AND LEAD TO SERIOUS PHYSICAL INJURY. JORO Manufacturing cannot take any responsibility for damage or injury resulting from improper installation. Do not operate Pro‐LIFT WMH if there are any obstructions below or above the board. Doing so may cause unit malfunction or lead to serious physical injury. The supplied mounting hardware is for use on the Pro‐LIFT stands only. If you encounter any problems or insufficient hardware during installation, please contact your local re‐seller. ...
- Page 3 WMH Main Frame Kit LCD Mount Fastener Kit (ONLY available with WMHL Models) WB Fastener Kit (ONLY available with WMHW Models) Machine Screw Insulator Note: Parts may not be exactly as shown and not to scale www.joromfg.com www.proliftstand.com COPYRIGHT 2014 ProLift WM Hybrid - WMHW ASSY Instructions : 0.003...
- Page 5 Low Profile Pro-LIFT WM Pencil Tray Adapter Nylon Washer For ease of installation, do this step while Pro-LIFT Wall Mount Hybrid is lying down BE AWARE the mounting position of the Pencil Tray Adapter is dependant on projector/white board combination...
- Page 6 2 Sacrificial Surface (recommended 3/4" thick) Be sure to fasten Sacrificial Surface to at least three joists www.joromfg.com www.proliftstand.com COPYRIGHT 2014 ProLift WM Hybrid - WMHW ASSY Instructions : 0.003...
- Page 7 3 Slotted Hex Washer Head Screw Slotted Hex Washer Head Screw Slotted Hex Washer Head Screw Mark out the two screw locations to hang the Wall Mount Hybrid Pre-drill pilot holes at the two locations Be sure both points are horizontal and level Fasten the two Slotted Hex Washer Head Screws in the pre-drilled holes www.joromfg.com www.proliftstand.com...
- Page 8 4 Slotted Hex Washer Head Screw Hang the Wall Mount Hybrid on the two screws Add the remaining Slotted Hex Washer Head Screws (3 per either side of Wall Mount Hybrid is recommended) Be sure Wall Mount Hybrid is securely fastened to wall by tightening all screws www.joromfg.com www.proliftstand.com COPYRIGHT 2014...
- Page 9 5 WB Hanger M6x8mm SILVER Button Head Mount the WB Hanger BE AWARE the mounting position of the WB Hanger is dependant on projector/white board combination Be sure to use the M6x8mm SILVER Button Head screws provided Be sure to NOT over tighten www.joromfg.com www.proliftstand.com COPYRIGHT 2014...
- Page 10 6 M6 x 20mm Socket Cap Screw Low Profile Mount the Turret Head Be sure to use the M6 x 20mm Socket Cap Screws provided Be sure to NOT over tighten www.joromfg.com www.proliftstand.com COPYRIGHT 2014 ProLift WM Hybrid - WMHW ASSY Instructions : 0.003...
- Page 11 For WMHW Systems JORO Button Head Screw Wall Mount Hybrid Control Panel CTRLTUBE1020 7 Mount the Wall Mount Hybrid Control Panel Be sure to use the JORO Button Head Screws provided Be sure to NOT over tighten For WMHW-OD Systems (if ordered with your product) Wall Mount Hybrid Control Panel JORO Button Head Screw...
- Page 12 8 CTRLTUBE1020 CTRLTUBE1020 M6x8mm SILVER Button Head Mount the CTRLTUBE1020 Mounting position dependant on white board width Be sure to use the M6x8mm SILVER Button Head Screws provided Be sure to NOT over tighten www.joromfg.com www.proliftstand.com COPYRIGHT 2014 ProLift WM Hybrid - WMHW ASSY Instructions : 0.003...
- Page 13 9 Mounting patterns for tested projectors Match holes in the diagram to projection system being used Fasten projector to the corresponding holes using the JORO Button Head Screws supplied Be sure to NOT over tighten www.joromfg.com www.proliftstand.com COPYRIGHT 2014 ProLift WM Hybrid - WMHW ASSY Instructions : 0.003...
- Page 14 Mount the white board Use the holes which correspond to manufacturers recommended projector to image distance Fasten using the JORO Button Head screws supplied Be sure to NOT over tighten Note, there are drilled/tapped holes on the frame upright, if lowering the board is required 10 ...
- Page 15 11 M6x6mm Button Head M6x6mm Button Head JORO Button Head JORO Button Head To Heighten To Lower Adjusting Turret Head IF NECESSARY Loosen JORO Button Head Screws 1 turn each side Adjust the M6x6mm Button Head Screws accordingly Be sure re-tighten JORO Button Head Screws - DO NOT OVER TIGHTEN! www.joromfg.com www.proliftstand.com COPYRIGHT 2014...
- Page 16 12 ...
- Page 17 Page Left Blank On Purpose ...
- Page 19 1 Sacrificial Surface (recommended 3/4" thick) Be sure to fasten Sacrificial Surface to at least three joists www.joromfg.com www.proliftstand.com COPYRIGHT 2014 ProLift WM Hybrid - WMHL ASSY Instructions : 0.003...
- Page 20 2 Slotted Hex Washer Head Screw Slotted Hex Washer Head Screw Slotted Hex Washer Head Screw Mark out the two screw locations to hang the Wall Mount Hybrid Pre-drill pilot holes at the two locations Be sure both points are horizontal and level Fasten the two Slotted Hex Washer Head Screws in the pre-drilled holes www.joromfg.com www.proliftstand.com...
- Page 21 3 Slotted Hex Washer Head Screw Hang the Wall Mount Hybrid on the two screws Add the remaining Slotted Hex Washer Head Screws (3 per either side of Wall Mount Hybrid is recommended) Be sure Wall Mount Hybrid is securely fastened to wall by tightening all screws www.joromfg.com www.proliftstand.com COPYRIGHT 2014...
- Page 22 For WMHW Systems JORO Button Head Screw Wall Mount Hybrid Control Panel CTRLTUBE1020 4 Mount the Wall Mount Hybrid Control Panel Be sure to use the JORO Button Head Screws provided Be sure to NOT over tighten For WMHW-OD Systems (if ordered with your product) JORO Button Head Screw Wall Mount Hybrid Control Panel...
- Page 23 5 CTRLTUBE1020 CTRLTUBE1020 M6x8mm SILVER Button Head Mount the CTRLTUBE1020 Mounting position dependant on LCD width Be sure to use the M6x8mm SILVER Button Head Screws provided Be sure to NOT over tighten www.joromfg.com www.proliftstand.com COPYRIGHT 2014 ProLift WM Hybrid - WMHL ASSY Instructions : 0.003...
- Page 24 6 WMH-LCD Hanger M6x8mm SILVER Button Head Mount the WMH-LCD Hanger Be sure to use the M6x8mm SILVER Button Head screws provided Be sure to NOT over tighten www.joromfg.com www.proliftstand.com COPYRIGHT 2014 ProLift WM Hybrid - WMHL ASSY Instructions : 0.003...
- Page 25 7 NOTE the VESA mounting locations These locations are where to mount the WMH-LCD Angle Tube according to the horizontal VESA pattern on your LCD www.joromfg.com www.proliftstand.com COPYRIGHT 2014 ProLift WM Hybrid - WMHL ASSY Instructions : 0.003...
- Page 26 8 WMH-LCD Angle Tube M6 x 20mm Socket Cap Screw Match holes in the WMH-LCD Angle Tube to the VESA holes from Step #6 diagram Be sure to use the M6 x 20mm Socket Cap Screw screws provided Be sure to NOT over tighten www.joromfg.com www.proliftstand.com COPYRIGHT 2014...
- Page 27 Be sure to NOT over tighten Shoulder Bolts Pro-LIFT LCD Arm Hang the Pro-LIFT LCD Arms (with LCD attached) on to the Shoulder Bolts Be sure the Pro-LIFT LCD Arms are securely on the Shoulder Bolts www.joromfg.com www.proliftstand.com COPYRIGHT 2014...
- Page 28 10 5/16x3/4" SILVER Button Head 5/16x3/4" SILVER Button Head Secure the Pro-LIFT LCD Arms Be sure to use the 5/16x3/4" SILVER Button Head screws provided Be sure to NOT over tighten www.joromfg.com www.proliftstand.com COPYRIGHT 2014 ProLift WM Hybrid - WMHL ASSY Instructions : 0.003...
- Page 29 11 Wire Mgmt Molding Mount the Wire Mgmt Molding JORO recommends attaching the Wire Mgmt Moldings supplied Remove the backing from the double sided tape and attach to side of frame upright www.joromfg.com www.proliftstand.com COPYRIGHT 2014 ProLift WM Hybrid - WMHL ASSY Instructions : 0.003...
- Page 30 12 ...
Need help?
Do you have a question about the WMH Series and is the answer not in the manual?
Questions and answers