Related Manuals for Sellenis Videojet 1000 Series
Summary of Contents for Sellenis Videojet 1000 Series
- Page 1 How to remove & replace the nozzle Videojet®1000 series printers Our guarantee: you pay less, we deliver more...
-
Page 2: Tools Required
Tools required •Hexagonal key or ball driver 1.5mm •Nut runner or spanner 5mm •Torque driver with 1.2mm hexagonal key •Drill Ø1.8mm Our guarantee: you pay less, we deliver more... - Page 3 components Description of the nozzle Modulation electrical connection Nozzle holder Nozzle Ink manifold Nozzle locking screw Nozzle locking nut Our guarantee: you pay less, we deliver more...
- Page 4 Step 1 Disconnect the ink manifold and the modulation electrical connection Step 1- Disconnect modulation wire & manifold Using the ball driver unscrew the manifold holding screw Our guarantee: you pay less, we deliver more...
- Page 5 Step 2 Loosen the locking nut on the nozzle mount Step 2- Loosen locking nut Using the nut spinner or a spanner, loosen the locking nut by turning anti-clock wise ½ to 1 turn ½ - 1 turn Our guarantee: you pay less, we deliver more...
- Page 6 Step 3 Loosen the nozzle mount locking screw Step 3- Loosen locking screw Using the ball driver, loosen the nozzle mount locking screw by turning anti-clock wise 1 to 2 turns 1 – 2 turns Our guarantee: you pay less, we deliver more...
- Page 7 Step 4 nozzle Removing old Step 4- removing the old nozzle Push back and carefully slide the old nozzle out Take care not to damage the modulation electrode Our guarantee: you pay less, we deliver more...
- Page 8 Step 5 Installing the new nozzle Step 5- Installing the new nozzle Use the 1.8mm drill to set the gap between the face of the nozzle and the charge electrode. Insert the new nozzle onto the nozzle holder as shown ensure the pipes locate well inside the holder.
- Page 9 Tighten the locking screw using a torque driver fitted with 1.2mm hexagonal key and set to 15Ncm (sellenis can provide the tools if required) Ø1.8mm 15 Ncm Our guarantee: you pay less, we deliver more...
- Page 10 Step 7 Tighten the nozzle mount locking nut Step 7- Tighen the locking nut using the nut runner or nut spinner tigthen the nozzle mount locking nut Our guarantee: you pay less, we deliver more...
- Page 11 Step 8 Reconnect the ink manifold and the modulation electrical connection Step 8- reconnect modulation wire & ink manifold Connect the modulation wire Reconnect the ink manifold Our guarantee: you pay less, we deliver more...
- Page 12 Step 9 Nozzle – jet alignment Step 9- Jet Alignment To align the jet in the gutter: i. Unlock the jet alignment mechanism by turning the screw anti-clockwise (see photo) ii. Now align the jet to the desired position in the gutter by turning the adjusting screw while observing the jet in the gutter.
- Page 13 Step 10 Jet Alignment Step 10- Jet Alignment To align the jet in the gutter (to the back or the front of the gutter): i. Unlock the jet alignment mechanism by turning the screw anti-clockwise (see photo) ii. Now align the jet to the desired position in the gutter by turning the adjusting screw while observing the jet in the gutter.
-
Page 14: Legal Disclaimer
All the trademarks or brands in this document may be registered in the United States and the UK and could be pending or registered in other countries by their respective owner. Sellenis, Limited and its products have not been, in any way, endorsed, sponsored, affiliated with or otherwise authorized by Videojet®, Willett®, Domino®, Imaje®, Linx®, Hitachi®...
Need help?
Do you have a question about the Videojet 1000 Series and is the answer not in the manual?
Questions and answers