Table of Contents
Advertisement
Quick Links
Copyright © 2008 Electronics for Imaging, Inc.
Addendum to the Fiery X3eTY2 Service Guide
If you are installing system software version 1.0a on the Fiery X3eTY2, this addendum
replaces the section "Installing system software over the network port" in the
Fiery X3eTY2 Service Guide. Be sure to use the procedure described in this addendum,
and disregard the corresponding procedure documented in the Service Guide.
If you are installing system software version 1.0 on the Fiery X3eTY2, do not use the
procedure described in this addendum. Disregard this addendum, and use the procedure
documented in the Service Guide instead.
Installing system software over the network port
The System Software DVD contains the system software and Fiery System Software
Installer. To install system software using the network port on the Fiery X3eTY2, you
need the following:
• Ethernet cross-over cable (4-pair/8-wire, short-length)
For 100BaseTX—Category 5 or higher
For 1000BaseT—Category 5e or higher
• Windows XP/2000 computer with:
• A DVD-ROM drive, built in or attached
• Support for 100BaseTX or 1000BaseT
• 512MB minimum memory capacity
Part Number: 45071816
25 February 2008
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Fiery X3eTY2
Summary of Contents for Fiery X3eTY2
- Page 1 Fiery X3eTY2 Service Guide. Be sure to use the procedure described in this addendum, and disregard the corresponding procedure documented in the Service Guide. If you are installing system software version 1.0 on the Fiery X3eTY2, do not use the procedure described in this addendum. Disregard this addendum, and use the procedure documented in the Service Guide instead.
- Page 2 To avoid confusion, ignore the text and graphics on the Confirmation screen. The screen may not accurately depict Fiery X3eTY2 hardware. 7. Shut down and power off the Fiery X3eTY2 and copier (see the Service Guide). 8. Disconnect all cables and devices from the Fiery X3eTY2 connector panel, except for the...
- Page 3 ON position. Fiery X3eTY2 service switches IGURE 11. Power on the Fiery X3eTY2 using its dedicated AC power switch, make sure that the soft power button lights up, and wait approximately 15 seconds for the DIAG LEDs to reach FF.
- Page 4 Fiery X3eTY2. If prompted, select the PC network card to use for the installation, and click OK. If you receive a Windows firewall or security alert, select the option to unblock the Fiery installer so that installation can proceed.
- Page 5 21. Power on the Fiery X3eTY2 by moving the AC power switch on the connector panel to the ON position (|), and make sure that the soft power button lights up.
- Page 6 • Controller button becomes active on the copier Control Panel LCD under MACHINE mode • Fiery X3eTY2 start page is printed (if the correct paper stock is loaded) 23. If needed, press the MACHINE button on the copier. Press the Controller button, and then press Setup.
- Page 7 • If you reinstalled system software version 1.0a (that is, if version 1.0a was previously installed on the Fiery X3eTY2 and you just reinstalled it), be sure to reinstall all software patches that were previously installed on the Fiery X3eTY2. For a list of previously installed patches, refer to the Configuration page that you printed earlier.
- Page 8 The Fiery X3eTY2 start page fails The copier is not loaded with the required Load the copier tray with 64–74 gsm letter or A4 stock (depending on the language of the Fiery X3eTY2 to print from the copier after the paper stock.
Need help?
Do you have a question about the X3eTY2 and is the answer not in the manual?
Questions and answers