STIEBEL ELTRON CON 5 Premium Operation And Installation
Wall mounted convector heater
Hide thumbs
Also See for CON 5 Premium:
Subscribe to Our Youtube Channel
Related Manuals for STIEBEL ELTRON CON 5 Premium
Summary of Contents for STIEBEL ELTRON CON 5 Premium
- Page 1 OPERATION AND INSTALLATION Wall mounted convector heater » CON 5 Premium » CON 10 Premium » CON 15 Premium » CON 20 Premium » CON 30 Premium...
-
Page 2: Table Of Contents
CONTENTS | SPECial iNfOrmaTiON SPECial iNfOrmaTiON SPECIAL INFORMATION OPERATION General information �����������������������������������������3 Safety instructions ����������������������������������������������� 3 - Keep children under the age of 3 away from Other symbols in this documentation ����������������������� 3 the appliance if constant supervision cannot Information on the appliance ��������������������������������� 3 be guaranteed. -
Page 3: Operation
OPEraTiON General information Other symbols in this documentation - The power cable must only be replaced (for example if damaged) by a qualified contrac- Note tor authorised by the manufacturer, using an General information is identified by the adjacent symbol. original spare part. -
Page 4: General Safety Instructions
OPEraTiON appliance description General safety instructions CAUTION Burns Parts of the appliance can get very hot and may cause WARNING Injury burns. Particular caution is advised when children or - Keep children under the age of 3 away from the vulnerable persons are present. appliance if constant supervision cannot be guar- anteed. -
Page 5: Programming Unit
OPEraTiON Operation Programming unit Symbol Description Frost protection active: The appliance is operated using the programming unit which is The frost protection symbol is displayed if the set room tempera- located at the top right of the appliance front. ture is set to 7.0 °C. Use this setting to protect an unused room from frost damage. -
Page 6: Standby Mode
OPEraTiON Settings Standby mode Display Description Switch "Window open detection" function on and off If the Pro4 time program (120 minute timer) is activated, the Material losses "Window open detection" function is not active. In standby mode, the appliance will not switch on heating under any circumstances. - Page 7 OPEraTiON Settings To access the configuration menu, press and hold "Menu". After Theses phases are factory-set as follows: approx. 3 seconds, actual value I1 is displayed. - 08:00 h - 22:00 h: Comfort mode Use "+" and "–" to switch between the individual actual values, - 22:00 h - 08:00 h: Setback mode time programs and parameters.
-
Page 8: Cleaning, Care And Maintenance
OPEraTiON Cleaning, care and maintenance Troubleshooting 5.4.3 Parameter You can call up the following parameters: Problem Cause remedy Room does not get Temperature set too low Check the selected room Display Description Options warm enough. Ap- on the appliance. temperature. Adjust if nec- Room temperature offset ±3 °C | ±5 °F pliance does not get... -
Page 9: Installation
iNSTallaTiON Safety iNSTallaTiON 10. Installation 10.1 Minimum clearances Safety Only a qualified contractor should carry out installation, commis- sioning, maintenance and repair of the appliance. General safety instructions ≥100 ≥100 ≥500 We guarantee trouble-free function and operational reliability only if original accessories and spare parts intended for the appliance are used. -
Page 10: Appliance Installation
iNSTallaTiON installation 10.5 Electrical connection f Lift up the wall mounting bracket so that its lower holes match up with the markings you have just made on the in- stallation wall. WARNING Electrocution f Mark holes 3 and 4 on the installation wall. - Carry out all electrical connection and installation work in accordance with relevant regulations. -
Page 11: Commissioning
Hand over the operating and installation instructions to the user. 14. Specification 14.1 Dimensions and connections CON 5 Premium CON 10 Premium CON 15 Premium CON 20 Premium CON 30 Premium Appliance Width 1090 Entry electrical... -
Page 12: Data Table
| ENVirONmENT aND rECYCliNG Specification 14.2 Data table CON 5 Premium CON 10 Premium CON 15 Premium CON 20 Premium CON 30 Premium 202086 202087 202088 202089 202090 Electrical data Connected load 1000 1500 2000 3000 Power supply 1/N/PE ~ 230 V... - Page 13 NOTES www.stiebel-eltron.com CON Premium |...
-
Page 14: Warranty
9. The contact details for you to make your warranty claim are: Who gives the warranty Name: Stiebel Eltron (Aust) Pty Ltd 1. The warranty is given by Stiebel Eltron (Aust) Pty Ltd (A.B.N. 82 Address: 294 Salmon Street, 066 271 083), 294 Salmon Street, Port Melbourne, Victoria, 3207 Port Melbourne, (“we”, “us”... - Page 15 18. The Stiebel Eltron warranty for the unit is in addition to any rights and remedies you may have under the Australian Consumer Law.
- Page 16 Deutschland Verkauf Tel. 05531 702-110 | Fax 05531 702-95108 | info-center@stiebel-eltron.de STIEBEL ELTRON GmbH & Co. KG Kundendienst Tel. 05531 702-111 | Fax 05531 702-95890 | kundendienst@stiebel-eltron.de Dr.-Stiebel-Straße 33 | 37603 Holzminden Ersatzteilverkauf Tel. 05531 702-120 | Fax 05531 702-95335 | ersatzteile@stiebel-eltron.de Tel.
Need help?
Do you have a question about the CON 5 Premium and is the answer not in the manual?
Questions and answers