Related Manuals for Car-Interface.com v.LOGiC CI-V5-MMI3G-PNP
Summary of Contents for Car-Interface.com v.LOGiC CI-V5-MMI3G-PNP
- Page 1 v.LOGiC Intelligent Solution Interface CI-V5-MMI3G-PNP Compatible with Audi MMI3G Basic/High and MMI3G+ High navigation systems with 4pin HSD LVDS connector Version 19.10.2017 CI-V5-MMI3G-PNP...
- Page 2 Product features Interactive lane lines Own on-screen display and setup Rear-view camera input Automatic switching to rear-view camera input on engagement of reverse gear from all operation modes Front camera input Manual switching to rear-view camera ...
-
Page 3: Table Of Contents
Contents 1. Prior to Installation 1.1. Delivery contents 1.2. Check compatibility of vehicle and accessories 1.3. Setting the dip switches of the interface-box V5C-M653 1.4. LED’s of the interface-box V5C-M653 2. Connection schema 3. Installation 3.1. Connecting interface-box and harnesses 3.2. - Page 4 Legal Information By law, watching moving pictures while driving is prohibited, the driver must not be distracted. We do not accept any liability for material damage or personal injury resulting, directly or indirectly, from installation or operation of this product. This product should only be used while standing or to display fixed menus or rear-view-camera video when the vehicle is moving, for example the MP3 menu for DVD upgrades.
-
Page 5: Prior To Installation
1. Prior to installation Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources. 1.1. Delivery contents Take down the SW-version and HW-version of the interface boxes, and store this manual for support purposes. -
Page 6: Setting The Dip Switches Of The Interface-Box V5C-M653
1.3. Setting the dip switches of the interface-box V5C-M653 Dip 1 on the back of the interface-box V5C-M653 are used to set the monitor type. The default setting is: Head unit Dip 1 Dip 2 Dip 3 MMI3G High, MMI3G+ High No function No function MMI3G Basic... -
Page 7: Connection Schema
2. Connection schema Interface-box V5C-M653 REAR LVDS cable CAB-HSD-DD075-O LVDS cable Back of CAB-HSD-MR-060-OZ head unit 4-Pin HSD LVDS female vehicle harness +12V power out 2 +12V power out 1 V5C-AU03 Interface-box harness V5C-M653 FRONT Rear-view camera CAN HIGH Front camera CAN LOW +12V input Quadlock female... -
Page 8: Installation
3. Installation Switch off ignition and disconnect the vehicle’s battery! The interface needs a permanent 12V source. If according to factory rules disconnecting the battery is to be avoided, it is usually sufficient to put the vehicle is sleep-mode. In case the sleep-mode does not show success, disconnect the battery with a resistor lead. - Page 9 Connect the loose blue cable (CAN-low) of harness V5C-AU05 to the orange-brown Cable and the loose yellow cable (CAN-high) of harness V5C-AU05 to the orange- purple or orange-green cable on the vehicle power distributor (right edge of the dashboard). Note: The orange cable in the vehicle is always CAN-bus. The cable colour orange- brown is always CAN-low, the additional cable colour of orange for CAN-high can vary.
-
Page 10: Lvds Connection
3.2. LVDS connection Interface-box V5C-M653 REAR LVDS cable CAB-HSD-DD075-O LVDS cable CAB-HSD-MR-060-OZ 4-Pin HSD LVDS female Back of vehicle harness head unit Connect the female 4pin HSD LVDS connector of the LVDS cable CAB-HSD-DD075-O to the male 4pin HSD LVDS connector (LVDS-IN) on the rear of the interface-box V5C-M653. -
Page 11: After-Market Front Camera
3.2.1. After-market front camera 3.2.1.1. Connection to the after-market front camera Interface-box V5C-M653 FRONT V5C-AU03 harness Front camera +12V camera Power out 1 (max. 1A) power Connect the video RCA of the after-market front camera to the female RCA connector “FRONT CAM”... -
Page 12: Settings For Connecting An After-Market Front Camera
3.2.1.2. Settings for connecting an after-market front camera You have to configure some settings in the OSD-menus INPUTS and MISC if you want to connect an after-market front camera (Operation of the OSD: see chapter “OSD-Operation”). OSD-menu Menu item Setting Explication Keine Frontkamera angeschlossen INPUT... -
Page 13: After-Market Rear-View Camera
3.2.2. After-market rear-view camera 3.2.2.1. Connection to the after-market rear-view camera Interface-box V5C-M653 FRONT Rear-view V5C-AU03 camera Power out 2 (max. 1A) harness Connect the video RCA of the after-market rear-view camera to the female RCA connector “REAR CAM” of the interface box V5C-M653. The green wire of harness V5C-AU03 can be used for +12V electric power supply (max. -
Page 14: Settings For Connecting An After-Market Rear-View Camera
3.2.2.2. Settings for connecting an after-market rear-view camera You have to configure some settings in the OSD-menus INPUT and OPTION if you want to connect an after-market rear-view camera (Operation of the OSD: see chapter “OSD- Operation”). OSD-menu Menu item Setting Explication No rear-view camera connected... -
Page 15: Configurable Trigger Outputs
3.2.3. Configurable trigger outputs Interface-box V5C-M653 FRONT Power out 1 (max. 1A) V5C-AU03 harness Power out 2 (max. 1A) You can configure the both +12V trigger outputs separately. The pink wire is POWER OUT 1 and the green wire is POWER OUT 2. Note: You can configure the both trigger outputs in the OSD-menu OPTION separately (Operation of the OSD: see chapter “OSD-Operation”). -
Page 16: Interactive Lane Lines
3.3. Interactive lane lines You have to configure some settings in the OSD-menu OPTION if you want to activate interactive lane lines (Operation of the OSD: see chapter “OSD-Operation”). OSD-menu Menu item Setting Explication Interactive lane lines deactivated RVC GRAPHIC LINES Interactive lane lines activated OPTION... -
Page 17: Operation
4. Operation 4.1. OSD – On-screen display You can change the basic configurations of the interface in the OSD (on screen display). 4.1.1. OSD – Operation You can control the OSD by MMI control buttons. Options Long press = enter OSD Version 19.10.2017 CI-V5-MMI3G-PNP... -
Page 18: Osd - Additional Setting Options
4.1.2. OSD – Additional setting options The following settings in the OSD-menus OPTION and OSD can be configured over and above the described settings in this manual (Operation of the OSD: see chapter “OSD-Operation”): OSD-menu Menu item Setting Explication POS. X 0-xxx Horizontal position of the OSD POS. -
Page 19: Selecting The Interface As Current Video Source
4.2. Selecting the interface as current video-source Long press “MEDIA” button to choose the interface as current video source. Short press ”MEDIA” button switch the video sources (cameras). Each short press will switch to the next enabled input. If all inputs are enabled the order is: ... -
Page 20: Specifications
5. Specifications Operation voltage 10.5 – 14.8V DC Stand-by power drain <0,1mA Operation power drain 190mA Power consumption 2,6W Temperature range -20°C to +80°C Weight (box only) 285g Measurements (box only) B x H x T 141 x 30 x 105 mm 6.
Need help?
Do you have a question about the v.LOGiC CI-V5-MMI3G-PNP and is the answer not in the manual?
Questions and answers