Download
Share
Print this page
Toro 2226 Software Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Farm Equipment
  5. 2226
  6. Software manual

Toro 2226 Software Manual

Directional drill
Hide thumbs Also See for 2226:

Advertisement

Quick Links

Download this manual
2226 Directional Drill
Model No. 23803—Serial No. 400000000 and Up
Software Versions: A.5, A.6, and Rev B
Introduction
Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. You are responsible for
operating the product properly and safely. Read your
Operator's Manual for more information.
Product Overview
Display Screen Buttons
1. Button 1
2. Button 2
3. Button 3
4. Button 4
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Figure 1
5. Button 5
6. Button 6
7. Button 7
8. Button 8
Register at www.Toro.com.
1. Status bar
2. Escape button
3. Left arrow button
4. Up arrow button
Exit-Side Lockout Disabled
g277422
Startup Screen
Note:
Software version A.5 and above.
This exit side lockout disabled warning will appear if
you disabled the exit side lockout system.
See
Exit Side Lockout Settings (page 18)
the exit side lockout system
Original Instructions (EN)
Form No. 3434-704 Rev A
Software Guide
Figure 2
5. Down arrow button
6. Right arrow button
7. OK button
Figure 3
All Rights Reserved *3434-704* A
Printed in the USA
g277423
g270157
to enable

Advertisement

loading

Related Manuals for Toro 2226

Summary of Contents for Toro 2226

  • Page 1 Form No. 3434-704 Rev A 2226 Directional Drill Model No. 23803—Serial No. 400000000 and Up Software Guide Software Versions: A.5, A.6, and Rev B Introduction Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage.

  • Page 2: Home Screens

    Home Screens Main Information Screen This is the first screen that appears after the initial splash screen. To navigate between screens, use the left and right arrows. g270081 Figure 5 1. Carriage indicator 5. Engine speed (rpm) 2. Drill speed (rpm) 6.
  • Page 3 Push buttons 2 and 3 to switch choose a row. Push button 5 to switch between thrust force, drill speed (rpm), and rotary torque. Use buttons 6 and 7 to set limits for the drill speed (rpm), rotary torque, and thrust force. g236827 Figure 7 1.
  • Page 4 Cruise Mode and Screen Software version Rev B and up. Cruise mode is identified by this icon: Cruise mode provides hands-free operation for rotary and thrust, set by the operator. Note: Use Cruise mode for pull back only. Using cruise mode in thrust could cause damage. You can only use cruise mode with clockwise functions.
  • Page 5 The following table describes the function values affected when another function is given priority. The priority is the function with the highest value, not the value selected in the screen. All values are dependent on the available engine horse power. Button Priority Icon...
  • Page 6 Carve Mode and Screen Carve mode is identified by this icon: Carve mode can only be set in thrust, not pullback. Accessing the Carve Screen Push the carve button on the joystick (Figure 12) or push button 4 on the home screen to access the carve screen.
  • Page 7 The following table describes the function values affected when another function is given priority. The priority is the function with the highest value, not the value selected in the screen. All values are dependent on the available engine horse power. Button Priority Icon...
  • Page 8 SmartTouch™ Home Screen SmartTouch mode allows the operator to load and unload pipes from the pipe box with less joystick operation to reduce operator fatigue. Use the Carriage Settings Screen (page 17) to turn SmartTouch mode on and off. Note: The Push/Pull Icon has a green background when SmartTouch mode is on and a ribbon appears at the bottom of the screen showing a sequence of...
  • Page 9 Release the button to proceed to the next step in the sequence (Figure 18). g236959 Figure 18 Break the pipe connection; refer to Removing Drill Pipes in the Operator’s Manual. Hold the lower left button on the left joystick to grip the pipe (Figure 19 Figure 20) and...
  • Page 10 Hold the lower right button on the left joystick Release the button to proceed to the next step (Figure 14) until the arms fully retract (Figure in the sequence (Figure 25). 22). g236962 Figure 25 g236960 Figure 21 Hold the lower right button on the left joystick (Figure 14) until the display moves to box 1 and the elevator puts the pipe back in the pipe...
  • Page 11 Pushing Pipe in SmartTouch Mode Start the SmartTouch mode with the cam assembly in the park position. g210463 Figure 30 g236957 Figure 27 Release the button to proceed to the next step 1. Go to the previous step 2. Go to the next step in the sequence (Figure 31).
  • Page 12 g236965 Figure 33 Hold the lower right button on the left joystick (Figure 27) until the arms extend (Figure 34). g238411 Figure 37 Hold the lower right button on the left joystick (Figure 27) until the arms retract and the cam assembly returns to the home position (row 3) (Figure 39).
  • Page 13 Manual Pipe Loading Manual pipe loading mode allows the operators to load and unload pipes from the cam assembly when it is rotated outside the pipe box. Note: Use 2 people to load the pipes into the cam assembly. g238408 Figure 40 Set the machine to manual pipe loading mode;...
  • Page 14 g238263 Figure 42 Use 2 people to load a pipe into the cam assembly (Figure 43). Lower the pipe loading guard (Figure 43). g238264 Figure 43 Lower the elevator (Figure 44). Push the cam rotate dial to rotate the cam assembly to the location picked in step 2 (Figure 44).
  • Page 15 g238312 Figure 44 Loading to the drill string only: Refer to Adding Drill Pipes in the Operator’s Manual. Repeat steps to continue loading pipes to the pipe box. Hours Screen Options Drilling Fluid (Mud) Use Screen To access this screen push button 2 on the Hours Machine Hours Screen screen.
  • Page 16 Maintenance Schedule Screens To access this screen, push button 3 on the Hours screen. These screens provide the user with the daily maintenance schedules and the 50-hour, 250-hour, 400-hour, and 800-hour increments. To reset the maintenance interval, refer to Maintenance PIN Screen (page 18).
  • Page 17 Settings Screen Options Control Mode Screen Push button 2 on the Settings screen. Carriage Settings Screen Use this screen to select between the 2 joystick control options. Push the up and down buttons to Push button 1 on the Settings screen. switch between Mode I and Mode II.
  • Page 18 Maintenance Options Screen Exit Side Lockout Settings Note: Software version A.5 and up Maintenance PIN Screen If your exit-side-lockout handheld remote loses its Push button 3 on the Settings screen. signal, runs out of batter power, or gets damaged, you can disable the system in order to continue working.

  • Page 19: Clock Settings Screen

    Language and Units Options Clock Settings Screen Screen Push button 7 on the Settings screen to set the clock settings options. Push button 5 on the Settings screen to access the screen to switch between English and metric units. Once you are on this screen, push button 7 to rotate Use the up and down arrow keys to change the between date, time, and 12/24.
  • Page 20 Calibrating the Joysticks Use this screen to check the calibration of the joysticks. Refer to Calibrating the Travel Pendant (page 24) to calibrate the travel pendant. The red dot is in the center of the targets shows the movement of the left and right joysticks. If the red dot does not reach ±10,000, see your Authorized Service Dealer to service or replace your joystick.
  • Page 21 Engine temperature: displays the engine coolant temperature. The temperature drops to 40°F when the engine is off. Battery voltage: displays the battery voltage. If the engine is off, the voltage is measured by the Toro controller. g238452 Figure 67 Hydraulic-fluid filter: the hydraulic fluid filter icon is green unless the filter is plugged then the indicator is red.
  • Page 22 Joystick Help Screen To access these screens push button 4 on the I/O screen. These screens show the function of each joystick button. Push the up and down arrows to scroll through the screens. g237129 Figure 71 g237126 Figure 68 g237130 Figure 72 g237127...
  • Page 23 Left Joystick I/O Screen To access this screen push button 5 on the I/O screen. Push the buttons on the joysticks and ensure that the corresponding icon illuminates. g237132 Figure 73 Right Joystick I/O Screen To access this screen push button 6 on the I/O screen. Push the buttons on the joysticks and ensure that the corresponding icon illuminates.
  • Page 24 Travel Pendant I/O and Calibration Engine DPF I/O Screen Screen To access this screen push button 8 on the I/O screen. Travel Pendant I/O Screen To access this screen push button 7 on the I/O screen. The travel pendant screen shows the voltage and position of the joystick located on the pendant.

  • Page 25: Troubleshooting

    Troubleshooting Software Information Screen To access this screen push button 3 on the Errors and Machine Information screen. Errors and Machine Information Screens This screen displays the machine and software information including the model, serial number, and software version. Drill Errors Screens To access this screen push button 1 on the Errors and Machine Information screen.
  • Page 26 Machine CAN Information Screen Push button 4 to access this screen. If any of these icons are red, refer to your Service Manual. g237120 Figure 80 Function I/O Screen To access this screen, push button 8 from the Errors and Machine Information Screens (page 25).
  • Page 27 Controller Icon Color Description Seat Switch Black The operator seat is occupied. Green The operator seat is unoccupied. Pedestrian Gate Black The gate is in the correct position for drilling. Black The gate is not in the correct position for drilling. Exit Side Lockout Black The exit side lockout is not in operation.
  • Page 28 Elevator Black The elevator down function is not in operation. Green The elevator is lowering. Black The elevator up function is not in operation. Green The elevator is raising. Black The grease is not in operation. Grease Green The grease is activated. Vice/Stationary Black The vice/stationary wrench is not in operation.

  • Page 29: Warning Icons

    Spray Gun Black The spray gun is not in operation. Green The spray gun is activated. Stake Black The stake (left/right) rotation function is not in operation. Green The stake (left/right) is rotating clockwise. Green The stake (left/right) is rotating counter clockwise. Black The stake (left/right) raise or lower function is not in operation.
  • Page 30 Warning Icon Description Resolution • Carriage The sensor on the drill carriage has Inspect the wires on the sensor. an error. • See your Authorized Service Dealer. Engine Air Filter The air filter is restricted. Refer to the Operator’s Manual to service the air filter.
  • Page 31 Notes:...

This manual is also suitable for:

23803