Page 1
DIGITAL NIGHT VISION InstructIon manual 30 / 4.5 40 / 6 Model #s: 260130 / 260140 / 260150...
Page 2
Parts anD controls GuIDE observe battery polarity marks inside battery compartment when inserting batteries, and ensure polarity marks on cap match polarity in battery compartment when replacing cap (+ to + and - to -). under Interface cover Flap...
Congratulations on the purchase of your Bushnell® Equinox Z™ Digital Night Vision. Comprised of high quality electronics and optics, the Bushnell Equinox Z is a hand-held digital night vision viewing system that utilizes an infrared sensitive CMOS sensor, providing edge-to-edge resolution and outstanding image quality. Fully multi-coated optics increase light transmission and decrease glare.
CONTROLS /FUNCTIONS POWER BUTTON (A) The Power button (Power icon) turns the unit on or off. • Press and hold the power button for 2 seconds to turn the unit ON • Press and hold the power button for 2 seconds to turn the unit OFF DIGITAL ZOOM BUTTONS (B) The “+”...
Page 5
the 6x model, to reduce the IR LED brightness to its lowest setting, indicated by “IR1” in the display. • Press the “IR” button again to switch off the IR LED light. “IR0” will be shown at the lower center of the display. Switching off the IR LED when ambient light levels are adequate for viewing without it (full moon, near streetlights, etc.) will extend battery life and running time.
Page 6
at a resolution of 640x480 pixels. • When the unit is in Video Mode, pressing the record button will start a new video recording. The Record icon in the display will begin flashing, and the Video Time display will increase as the recording continues. Video is captured in .avi format at a resolution of 640x480 pixels per frame (VGA).
2) rEMoVE LENS coVEr, aDJuSt DISpLaY (EYEpIEcE) FocuS For Your VISIoN Press the Power button (A) to turn on the unit. A battery level icon is displayed at the top right corner of the screen. While looking through the eyepiece (M) at the LCD display screen, rotate the eyepiece (eyecup) until the display icons or edges of the display screen appear sharp to your eye.
CARE AND MAINTENANCE Your Bushnell Equinox Z Digital Night Vision device was designed to provide many years of reliable service. To ensure that you get the most enjoyment out of your Digital Night Vision device, always obey the following warnings and precautions.
DIsPlaY Icons The photo count, remaining record time, and SD card status will be displayed here Photo Count Remaining Recording Time Elapsed Recording Time No SD Card When the device is in Photo When the device is in Video When the device is in Video When an SD card is not present mode, the number of photos mode and not recording, the...
Avoid removing the eyepiece as the LCD display could become damaged. Do not leave the device in direct sunlight or rain. The unit is water resistant, but is not designed for prolonged exposure to moisture and cannot be submerged in water. After the unit is operated in temperatures below zero, wait at least 3 hours at room temperature, to avoid condensation accumulating on the ...
tEcHnIcal sPEcIFIcatIons Specification 260130 260140 260150 Magnification (optical) 4.5x Magnification (with digital zoom) 3.3x-9.0x 5.0x-13.5x 6.6x-18.0x Objective Size 30mm 40mm 50mm Battery Type 4x AA, lithium, alkaline or NiMh Viewing Range 500 ft / 152 m 750 ft / 229 m 1000 ft / 305 m Field of View @ 100 yds/m 30 ft / 10 m...
Fcc notE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Need help?
Do you have a question about the Equinox Z 260130 and is the answer not in the manual?
Questions and answers