LEGRAND Da-Lite Advantage Electrol Instruction Book
  1. Manuals
  2. Brands
  3. LEGRAND Manuals
  4. Projection Screen
  5. Da-Lite Advantage Electrol
  6. Instruction book

LEGRAND Da-Lite Advantage Electrol Instruction Book

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION BOOK FOR
Tensioned Advantage
Electrol
®
®

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Da-Lite Advantage Electrol and is the answer not in the manual?

Questions and answers

Related Manuals for LEGRAND Da-Lite Advantage Electrol

Summary of Contents for LEGRAND Da-Lite Advantage Electrol

  • Page 1 INSTRUCTION BOOK FOR Tensioned Advantage Electrol ® ®...

  • Page 2: Important Safety Instructions

    Legrand AV makes no representation of warranty, expressed or implied, regarding the information contained herein.
  • Page 3 Tensioned Advantage Electrol Suggested Methods of Installation ® ® Method 1 6 1/16" 6 7/16" 7 3/4" Variable Position Mounting Bracket 9 1/4" Audience Side Motor 6 1/16" 3/8" Threaded Rod (Not Included) Electrical Attached To Junction Box Mounting Bracket 6 3/8"...

  • Page 4: Tools Required For Installation

    Tools Required for Installation 1/2“ and 5/16" Open Wrench 1/8” Hex Key or Socket Driver (included) Pre-Installation 1. Carefully unpack case from shipping carton. 5. For shipping purposes, foam is also inserted between the roller brackets and end caps (Figure 1). Remove these foam 2.
  • Page 5 Screen And Roller Assembly Installation Tools required for screen and roller assembly: #2 Phillips Screwdriver 1/2“, 1/4" and 5/16" Open Wrench or Socket Driver Follow these steps if your screen and roller assembly was ordered separately from the case. Remove the access door. First, remove the 2 screws from the 5.
  • Page 6 Screen And Roller Assembly Installation (continued) Replacement Motor Instruction Rated torque of model DL45E-10/26 is 10 N/m with a duty cycle of 1 min. on / 3 min. off. Rated torque of model DL45EQ-6/28 is 6 N/m with a duty cycle of 1 min. on / 3 min. off. Motor is intended for use in Da-Lite screens incorporating a 3.00"...
  • Page 7 Tensioned Advantage Electrol Installation for 120V Screens ® ® 120V Wiring Diagram IMPORTANT NOTE: The wall switch is REQUIRED to make any limit switch adjustments, EVEN if a third party control system is 3-conductor 20–24 gauge wire can be used in place of the S T O used.
  • Page 8 Tensioned Advantage Electrol Installation for 220V Screens ® ® 220V Wiring Diagram with Operation & Limit Adjustment IMPORTANT NOTE: The wall switch is REQUIRED to make any Wall Switch limit switch adjustments, EVEN if a third party control system is S T O used.
  • Page 9 Tensioned Advantage Electrol Installation for 220V Screens (continued) ® ® 220V Wiring Diagram with European Style Wall Switch IMPORTANT NOTE: The European style wall switch is for operation only and CANNOT be used to make limit switch Use 3-conductor 20–24 gauge wire for wall switch connections. adjustments.
  • Page 10 Optional Built-In Video Projector Interface CAUTION: The projector must be turned off before IMPORTANT NOTE: The wall switch is REQUIRED to make any connecting the trigger wires to the projector. Failure to limit switch adjustments, EVEN if a third party control system is do so may damage the controller.

  • Page 11: Wall Switch

    Optional Built-In SCB-100 BUILT-IN SCB-100 CONTROL RS-232 COMMUNICATIONS The command protocols are as follows. Locate the 11-pin connector in the junction box of the screen. Screen 1 up: RS-232 PORTS Screen 1 stop: The SCB-100 has two RS-232 ports. Both ports have three Screen 1 down: wire connections.

  • Page 12: Screen Adjustment

    Screen Adjustment For Screens with Standrd Built-In Low Voltage Control or Optional VPI If your Tensioned Advantage Electrol was ordered as a complete unit, the up and down limits were pre-set by Da-Lite. If your screen and roller assembly was ordered separately from the case, or if general adjustment is needed, please follow the steps below and refer to the Wiring Diagram.
  • Page 13 Screen Adjustment (continued) For Screens with Optional SCB-100 Remove two screws to remove access door. NOTE: Use a screwdriver or 5/32" Allen wrench to make adjustments. SETTING THE DOWN LIMIT POSITION To Reduce Screen Drop: Turn the "down" limit switch screw clockwise to decrease the amount of screen drop.

  • Page 14: Operation Of Screen

    Operation of Screen Operation & Limit Adjustment Wall Switch “Up” Button Press ”DOWN” button on screen switch and screen will deploy out of case in downward direction. “Stop” Button 2. Press “STOP “button on screen switch and screen will stop if in movement.

  • Page 15: Troubleshooting

    Troubleshooting Symptom Cause Solution Verify 115-125V (or 220-240V). If insufficient voltage, rewire Incorrect line voltage. incoming electric line. Blown fuse. Replace fuse. Tripped circuit breaker. Reset circuit breaker. Screen will not operate and motor does not hum. Check above. Tighten all loose wire connections. Correct any improper connections.
  • Page 16 LIMITED FIVE YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS Legrand AV Inc. warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in materials and workmanship for a period of five (5) years from the date of purchase by the original purchaser; provided they are properly operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the factory.

Table of Contents