LEGRAND 14975L User Manual

Hide thumbs

page of 61

/ 61
Bookmarks

Quick Links

Download this manual

Tensioned

Advantage

Series

USER MANUAL

200076 Rev D

Need help?

Do you have a question about the 14975L and is the answer not in the manual?

Questions and answers

Summary of Contents for LEGRAND 14975L

Page 1 Tensioned Advantage ® Series USER MANUAL 200076 Rev D...
Page 2 TABLE OF CONTENTS Tensioned Advantage (With Closure Door) ® Previously Named: Tensioned Advantage Deluxe Electrol Tensioned Advantage Previously Named: Tensioned Advantage Electrol Tensioned Advantage with SightLine Tensioned Advantage (Over 14' W with Closure Door) Previously Named: Tensioned Large Advantage Deluxe Electrol Tensioned Advantage (Over 16' W) Previously Named: Tensioned Large Advantage Electrol...
Page 3 Tensioned Advantage ® (with Closure Door) USER MANUAL 200072 Rev C 88585...
Page 4 Incorrect reassembly can cause electric shock Da-Lite® is a registered trademark of Legrand AV. All when the appliance is used subsequently. rights reserved. 5. The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire, electric shock, or injury to persons.
Page 5 PRE-INSTALLATION CASE INSTALLATION 1. Carefully unpack screen and remove outer wrapping 1. The case provides multiple attachment points for from case. bolts, cables, or threaded rod. Page 7 shows threaded rod installed. The variable position- 2. Make sure to recheck measurements of screen mounting bracket may be located anywhere along location before installation.
Page 6 SCREEN AND ROLLER ASSEMBLY INSTALLATION If your screen was shipped with the motor and roller already installed proceed to step 6. 1. Remove the screw from each end of the access door 7. Test installation by operating the screen several (front door) and open the door.
Page 7 SCREEN ADJUSTMENT NOTE: Use a screw driver or 5/32" Allen wrench to make adjustments. More Screen Drop Less Screen Drop 1. Place operating switch in “down” position. 1. Raise picture surface approximately two feet above desired level. 2. When the screen stops, turn the “down” limit knob (Fig.
Page 8 TENSIONED ADVANTAGE (WITH CLOSURE DOOR) INSTALLATION 7 1/4" 7 1/4" Case Length Variable Position Mounting Brackets Flat Bracket Mounting Method 7 5/8" 9 1/4" Motor End Electrical (Suggested) 3/8" Junction Box Threaded Rod (Not Included) 7 5/8" Attached to Mounting 7 1/4"...
Page 9 TENSIONED ADVANTAGE (WITH CLOSURE DOOR) INSTRUCTIONS FOR STANDARD CONTROL 120V Wiring Diagram FRONT OF BACK OF NOTE: 20-24AWG Wire WB R WALL WALL STOP Recommended For Connecting Wall SWITCH SWITCH DOWN NOTE: Electrical connections Switch to the Dual Motor Controller on left end of case.
Page 10 TROUBLESHOOTING SYMPTOM CAUSE SOLUTION Verify 115-125V (or 220-240V). If insufficient voltage, Incorrect line voltage. rewire incoming electric line. Screen will not Blown facility fuse. Replace facility fuse. operate or will not go “down. ” Tripped facility circuit breaker. Reset facility circuit breaker. Motor does not hum.
Page 11 TROUBLESHOOTING (CONT.) SYMPTOM CAUSE SOLUTION Hinge is bound or has a foreign substance on it Check installation to free door. Clear any foreign which does not allow it to open by gravity. substance; i.e., paint or plaster from hinge. Door will not open. No power.
Page 12 LIMITED FIVE-YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS Legrand AV Inc. warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in materials and workmanship for a period of five (5) years from the date of purchase by the original purchaser;...
Page 13 Tensioned Advantage ® USER MANUAL 200069 Rev D 84215...
Page 14 The content herein is subject to change without notice or obligation of any kind. To the maximum extent permitted by applicable law, Legrand AV makes no representation or warranty, expressed or implied, regarding the information contained herein. Furthermore, Legrand AV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Page 15 TENSIONED ADVANTAGE SUGGESTED METHODS OF INSTALLATION 6 1/16" Method 1 Audience 6 7/16" Side 7 3/4" Variable Position Mounting Bracket (See Table 1) 9 1/4" Audience Side Motor 6 1/16" 3/8" Threaded Rod (Not Included) Electrical Table 1 Attached To Junction Box Mounting Bracket Number of...
Page 16 TOOLS REQUIRED FOR INSTALLATION 1/2" and 5/16" Open Wrench 1/8" Hex Key or Socket Driver (included) PRE-INSTALLATION 1. Carefully unpack case from shipping carton. 5. For shipping purposes, foam is also inserted between the roller brackets and end caps (Figure 2.
Page 17 SCREEN AND ROLLER ASSEMBLY INSTALLATION Tools required for screen and roller assembly: #2 Phillips 1/2", 1/4" and 5/16" Screwdriver Open Wrench or Socket Driver Follow these steps if your screen and roller assembly was ordered separately from the case. 1. Remove the access door. First, remove the 2 end bracket ( junction box end) and secure with the screws from the ends using a #2 Phillips cotter pin (Figure 2).
Page 18 SCREEN AND ROLLER ASSEMBLY INSTALLATION (CONT.) Replacement Motor Instruction Rated torque of model DL45E-10/26 is 10 N/m with a duty cycle of 1 min. on / 3 min. off. Rated torque of model DL45EQ-6/28 is 6 N/m with a duty cycle of 1 min. on / 3 min. off. Motor is intended for use in Da-Lite screens incorporating a 3.00"...
Page 19 WIRING DIAGRAM FOR 120V SCREENS Wall Switch 120V Wiring Diagram IMPORTANT NOTE: The wall switch is REQUIRED to make any limit switch RJ-45 Input adjustments, EVEN if a third party control system is used. Therefore, it is advised to locate the wall switch in an Junction Box Cat5e or Cat6 Cable accessible location.
Page 20 WIRING DIAGRAM FOR 230V SCREENS Wall Switch 230V Wiring Diagram IMPORTANT NOTE: The wall switch is REQUIRED to make any limit switch RJ-45 Input adjustments, EVEN if a third party control system is used. Therefore, it is advised to locate the wall switch in an Junction Box Cat5e or Cat6 Cable accessible location.
Page 21 WIRING DIAGRAM FOR 230V SCREENS (CONT.) 230V Wiring Diagram with Opitonal European Style Wall IMPORTANT NOTE: The European style wall switch is for Switch operation only and CANNOT be used to make limit switch adjustments. Therefore, it is advised to locate the limit Use 3-conductor 20–24 gauge wire to connect European adjustment wall switch in an accessible location.
Page 22 SCREEN ADJUSTMENT If your Tensioned Advantage was ordered as a complete unit, the up and down limits were pre-set by Da-Lite. If your screen and roller assembly was ordered separately from the case, or if general adjustment is needed, please follow the steps below and refer to the Wiring Diagram.
Page 23 OPERATION OF SCREEN “Up” Button Operation & Limit Adjustment Wall Switch “Stop” Button 1. Press “DOWN” button on screen switch and screen will deploy out of case in downward direction. “Down” Button 2. Press “STOP” button on screen switch and screen will stop if in movement.
Page 24 TROUBLESHOOTING SYMPTOM CAUSE SOLUTION Verify 115-125V (or 220-240V). If insufficient voltage, Incorrect line voltage. rewire incoming electric line. Blown fuse. Replace fuse. Tripped circuit breaker. Reset circuit breaker. Screen will not operate and motor does not hum. Check above. Tighten all loose wire connections. Correct any improper connections.
Page 25 LIMITED FIVE-YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS Legrand AV Inc. warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in materials and workmanship for a period of five (5) years from the date of purchase by the original purchaser; provided they are properly operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the factory.
Page 26 Tensioned Advantage ® with SightLine™ USER MANUAL 210747 Rev B DL15520...
Page 27 The content herein is subject to change without notice or obligation of any kind. To the maximum extent permitted by applicable law, Legrand AV makes no representation or warranty, expressed or implied, regarding the information contained herein. Furthermore, Legrand AV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Page 28 TENSIONED ADVANTAGE WITH SIGHTLINE SUGGESTED METHODS OF INSTALLATION 6 1/16" Method 1 Audience 6 7/16" Side 5 5/16" Variable Position 7 3/4" Mounting Bracket (See Table 1) 9 1/4" Audience Side Motor 6 1/16" 3/8" Threaded Rod (Not Included) Electrical Table 1 Attached To Junction Box...
Page 29 TOOLS REQUIRED FOR INSTALLATION 1/2" and 5/16" Open Wrench 1/8" Hex Key or Socket Driver (included) PRE-INSTALLATION 1. Carefully unpack case from shipping carton. 5. For shipping purposes, foam is also inserted between the roller brackets and end caps (Figure 2.
Page 30 SCREEN AND ROLLER ASSEMBLY INSTALLATION Tools required for screen and roller assembly: #2 Phillips 1/2", 1/4" and 5/16" Screwdriver Open Wrench or Socket Driver Follow these steps if your screen and roller assembly was ordered separately from the case. 1. Remove the access door. First, remove the 2 end bracket ( junction box end) and secure with the screws from the ends using a #2 Phillips cotter pin (Figure 2).
Page 31 SCREEN AND ROLLER ASSEMBLY INSTALLATION (CONT.) Replacement Motor Instruction Rated torque of model DL45E-10/26 is 10 N/m with a duty cycle of 1 min. on / 3 min. off. Rated torque of model DL45EQ-6/28 is 6 N/m with a duty cycle of 1 min. on / 3 min. off. Motor is intended for use in Da-Lite screens incorporating a 3.00"...
Page 32 WIRING DIAGRAM FOR 120V SCREENS Wall Switch 120V Wiring Diagram IMPORTANT NOTE: The wall switch is REQUIRED to make any limit switch RJ-45 Input adjustments, EVEN if a third party control system is used. Therefore, it is advised to locate the wall switch in an Junction Box Cat5e or Cat6 Cable accessible location.
Page 33 WIRING DIAGRAM FOR 230V SCREENS Wall Switch 230V Wiring Diagram IMPORTANT NOTE: The wall switch is REQUIRED to make any limit switch RJ-45 Input adjustments, EVEN if a third party control system is used. Therefore, it is advised to locate the wall switch in an Junction Box Cat5e or Cat6 Cable accessible location.
Page 34 WIRING DIAGRAM FOR 230V SCREENS (CONT.) 230V Wiring Diagram with Opitonal European Style Wall IMPORTANT NOTE: The European style wall switch is for Switch operation only and CANNOT be used to make limit switch adjustments. Therefore, it is advised to locate the limit Use 3-conductor 20–24 gauge wire to connect European adjustment wall switch in an accessible location.
Page 35 SCREEN ADJUSTMENT If your Tensioned Advantage with SightLine was ordered as a complete unit, the up and down limits were pre-set by Da-Lite at 24". The desired amount of cable drop can be adjusted according to the instructions below. If your screen and roller assembly was ordered separately from the case, or if general adjustment is needed, please follow the steps below and refer to the Wiring Diagram.
Page 36 OPERATION OF SCREEN “Up” Button Operation & Limit Adjustment Wall Switch “Stop” Button 1. Press “DOWN” button on screen switch and screen will deploy out of case in downward direction. “Down” Button 2. Press “STOP” button on screen switch and screen will stop if in movement.
Page 37 TROUBLESHOOTING SYMPTOM CAUSE SOLUTION Verify 115-125V (or 220-240V). If insufficient voltage, Incorrect line voltage. rewire incoming electric line. Blown fuse. Replace fuse. Tripped circuit breaker. Reset circuit breaker. Screen will not operate and motor does not hum. Check above. Tighten all loose wire connections. Correct any improper connections.
Page 38 LIMITED FIVE-YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS Legrand AV Inc. warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in materials and workmanship for a period of five (5) years from the date of purchase by the original purchaser; provided they are properly operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the factory.
Page 39 Tensioned Advantage ® (Over 14' W with Closure Door) USER MANUAL 200073 Rev D 35898...
Page 40 The content herein is subject to change without notice or obligation of any kind. To the maximum extent permitted by applicable law, Legrand AV makes no representation or warranty, expressed or implied, regarding the information contained herein. Furthermore, Legrand AV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Page 41 TOOLS REQUIRED FOR CASE INSTALLATION INSTALLATION 1. The case provides multiple attachment points for bolts, cables, or threaded rod. Page 5 shows threaded rod installed. The variable position- mounting bracket may be located anywhere along the length of the case. It is recommended to keep the brackets spaced evenly enough to distribute the weight of the screen.
Page 42 INSTALLATION Screens Up to 16' Wide (Suggested) ½" Threaded Rod (Not Screen Included) Attached Roller 9 1/8" To Mounting Bracket Audience Side 12 3/16" 11 7/16" 11" Door Roller Finished Self-Trimming Self-Trimming Access Door Ceiling Flange Flange Closing Door 13 1/8" 10 13/16"...
Page 43 INSTALLATION Screens 18' and Wider (Suggested) ½" Threaded Rod (Not Included) Attached 9 1/8" To Mounting Screen Bracket Roller Electrical Junction Box Audience Side 121/4" 12" 12" Door Roller Finished Self-Trimming Self-Trimming Access Door Ceiling Flange Flange Closing Door 131/8" 10 13/16"...
Page 44 WIRING DIAGRAM NOTE: 20-24AWG Wire Recommended For Connecting Wall 120V FRONT OF BACK OF Switch to the Dual Motor Controller Wiring WB R WALL WALL STOP Diagram SWITCH SWITCH DOWN RED (UP) BLACK (DOWN) NOTE: Electrical connections WHITE (COMMON) on left end of case. Use provided knockouts for WHITE (COMMON) WHITE (COMMON)
Page 45 SCREEN AND ROLLER ASSEMBLY INSTALLATION If your screen was shipped with the motor and roller already installed proceed to step 9. 1. Remove four bolts from ends of door assembly (2 10. Test installation by operating the screen several bolts on each end) (Fig. 1). This will allow the door times.
Page 46 SCREEN ADJUSTMENT Less Screen Drop Surface travel is stopped automatically in the fully opened and closed positions by limit switches that 1. Raise picture surface approximately two feet are properly adjusted at Da-Lite. Should it be above necessary to adjust for more or less drop of picture, desired level.
Page 47 TROUBLESHOOTING SYMPTOM CAUSE SOLUTION Verify 115-125V (or 220-240V). If insufficient voltage, Incorrect line voltage. Screen will not rewire incoming electric line. operate or will not go “down. ” Blown facility fuse. Replace facility fuse. Motor does not hum. Tripped facility circuit breaker. Reset facility circuit breaker.
Page 48 TROUBLESHOOTING (CONT.) SYMPTOM CAUSE SOLUTION Spring has an obstruction not Check installation to free door. allowing door to open. Clear any foreign substance from spring. Door will not open. No power. See above. Mis-adjusted door motor limit. Adjust door motor limit. Call Da-Lite for instruction. Door does not close.
Page 49 LIMITED FIVE-YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS Legrand AV Inc. warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in materials and workmanship for a period of five (5) years from the date of purchase by the original purchaser; provided they are properly operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the factory.
Page 50 Tensioned Advantage ® (Over 16' W) USER MANUAL 200074 Rev D 35890...
Page 51 The content herein is subject to change without notice or obligation of any kind. To the maximum extent permitted by applicable law, Legrand AV makes no representation or warranty, expressed or implied, regarding the information contained herein. Furthermore, Legrand AV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Page 52 TOOLS REQUIRED FOR PRE-INSTALLATION INSTALLATION Carefully unpack case from shipping crate. Set aside the Installation Kit. Items inside will be used during installation. Make sure to recheck measurement of case for proper installation clearance. Remove any protective foam from case. 3/4"...
Page 53 SCREEN AND ROLLER ASSEMBLY INSTALLATION Tools required for screen and roller assembly: 1/8" Hex Key 9/16" Open Wrench 5/32" Hex 1/2" Open Wrench (included) or Socket Driver or Socket Driver If your screen was shipped with the motor and roller already installed proceed to step 7. 1.
Page 54 INSTALLATION Screens Up to 16' Wide* (Suggested) 1/2" Threaded Rod (Not Included) Attached to Mounting Bracket 1/8" Electrical Junction Screen Roller 3/16 " 11" Audience 11 7/16" Side Self-Trimming Flange Self-Trimming Access Door Flange Finished 3/16" 15/16" Ceiling " Variable Position Mounting Brackets Electrical Junction *Custom sizes only.
Page 55 INSTALLATION Screens 18' and Wider (Suggested) ½" Threaded Rod (Not Included) Attached 9 1/8" To Mounting Screen Bracket Roller Electrical Junction Box Audience Side 121/4" 12" 12" Finished Self-Trimming Self-Trimming Access Door Ceiling Flange Flange 131/8" 103/16" 3" 12" 10" Variable Case Length Position...
Page 56 SCREEN ADJUSTMENT Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly adjusted at Da-Lite. Should it be necessary to adjust for more or less drop of picture, proceed in the following manner: NOTE: Use a screw driver or 5/32"...
Page 57 120V WIRING DIAGRAM NOTE: 20-24 AWG wire recommended for connecting wall switch to low voltage controller. CAUTION: Do not use 3-position high voltage rocker switch with this unit! This will damage the low voltage control board. ATTENTION: NE UTILISEZ PAS l'interrupteur à bascule fourni avec l'écran.
Page 58 230V WIRING DIAGRAM NOTE: 20-24 AWG wire recommended for connecting wall switch to low voltage controller. CAUTION: Do not use 3-position high voltage rocker switch with this unit! This will damage the low voltage control board. ATTENTION: NE UTILISEZ PAS l'interrupteur à bascule fourni avec l'écran.
Page 59 TROUBLESHOOTING SYMPTOM CAUSE SOLUTION Verify 115-125V (or 220-240V). If insufficient voltage, Incorrect line voltage. rewire incoming electric line. Blown fuse. Replace fuse. Tripped circuit breaker. Reset circuit breaker. Screen will not operate and motor does not hum. Check above. Tighten all loose wire connections. Correct any improper connections.
Page 60 LIMITED FIVE-YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS Legrand AV Inc. warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in materials and workmanship for a period of five (5) years from the date of purchase by the original purchaser; provided they are properly operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the factory.
Page 61 EMEA +31 495 580 840 av.emea.sales@legrand.com APAC +852 2145 4099 av.asia.sales@legrand.com ©2024 Legrand AV Inc. 230327 Rev D 12/23 Da-Lite is a registered trademark of Legrand AV Inc. All other brand names or marks are used for identification purposes and are...

This manual is also suitable for:

Da-lite tensioned advantage series 34567lDa-lite advantage seriesDa-lite advantage with sightline seriesDa-lite advantage dl15268ls