Subscribe to Our Youtube Channel
Related Manuals for Plymovent SCS-DILUTER PRO
Summary of Contents for Plymovent SCS-DILUTER PRO
- Page 1 Environmental diluter system SC S-DILUTER Installation and user manual www.plymovent.com...
-
Page 2: Table Of Contents
Thus the manufacturer cannot be held responsible for any damage resulting from the application of this publication to the version actually delivered to you. This publication has been written with great care. However, the manufacturer cannot be held responsible, either for any errors occurring in this publication or for their consequences. 0000117016/010520/0 SCS-Diluter PRO... -
Page 3: Preface
Technical specifications Product type: Equals to: - ControlPro/Panel Panel 1.5.1 SCS-Diluter (filter system) - ControlPro/HMI - SCS-Diluter PRO SCS-Diluter Dimensions refer to Fig. I on page 20 Filter material cellulose fibres provided with precoat INTRODUCTION Filter surface area 2 x 75 m² (2 x 807 ft²) -
Page 4: Product Description
+20°C (68°F) +20°C (68°F) - max. +50°C (122°F) +50°C (158°F) Max. relative humidity Suitable for outdoor use Ambient temperature: 0°C (32°F) - min. Fig. 2.1 Main components and elements +20°C (68°F) - nom. +50°C (122°F) - max. 0000117016/010520/0 SCS-Diluter PRO... -
Page 5: Safety Instructions
- control cable the entire life of the product. - Immediately replace or repair damaged or illegible pictograms, warnings and instructions. CE (400V): circuit breakers | UL (480/600V): fuses 0000117016/010520/0 SCS-Diluter PRO... - Page 6 SCS-Diluter of your work. Do not install the product when you are under the Plymovent including the connected extraction fan. influence of drugs, alcohol or medicine. - Make sure that the workshop, in the vicinity of the product,...
-
Page 7: Installation
To install the filter system, do the following. E.g. heat gun, cable stripping tool The type of mounting material depends on the wall type Number and type of cables depend on the selected options and control equipment 0000117016/010520/0 SCS-Diluter PRO... - Page 8 • Put the spark arrester (upper part) (B) on top of the lower part. Euromate article number: Plymovent article number: 0000117016/010520/0 SCS-Diluter PRO DESCRIPTION: Clean Air Group B.V. EDS on frame with garbage P.O. Box 9350...
- Page 9 Put the duct on the silencer. Attach it with 8 self-tapping ATTENTION screws. Make sure that both the filter system and the extraction fan are level. To check this, put the level in vertical position on the filter base (so not on the frame). 0000117016/010520/0 SCS-Diluter PRO...
- Page 10 (ref. ISO 8573-3 class 6). 4.5.1 Filter pressure sensor Fig. 4.10 • Connect two pneumatic hoses to the + and – (B+C). Fig. 4.12 Connection of pneumatic hoses to the Panel Push-in fitting – (minus) remains unused 0000117016/010520/0 SCS-Diluter PRO...
- Page 11 D Universal cable glands M16 (4) Push-in fittings (3) for the pressure tubes • Loosen the locking screw (C) and the HMI (B) from the bracket (A). Fan pressure + | Filter pressure + and – Max. 4 0000117016/010520/0 SCS-Diluter PRO...
- Page 12 Table I on page 26 gives an overview of the necessary and optional cables that you need to install the system. Detachable screw terminal block (“connector”) 10. Recommended cable specifications; use cables with a max. wire diameter 1,5 mm² (AWG 16) 0000117016/010520/0 SCS-Diluter PRO...
- Page 13 Panel Vertical duct The motor cable and the PTC cable are supplied in the SCS-Diluter PRO package; - motor cable: 4-cored shielded cable 4 mm² - PTC cable: 2-cored shielded cable 0,75 mm² To install the motor cable and PTC cable to the Panel, do the following.
- Page 14 Connect the wires of the motor cable to the connectors U1, X3.1-2 V1, W1 (C) and PE (A) in the junction box of the fan. X3.3-4 X1.3-4 (compressed air) X3.5-6 X3.7-8 X3.9-10 X1.5-6 solenoid 0000117016/010520/0 SCS-Diluter PRO X3.11-12 X1.7-8 solenoid X3.13-14 X1.1-2 ∂P filter...
- Page 15 Fire alarm (Shie IN 3 Service mode switch IN 7 Sliding valve fe 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 0000117016/010520/0 SCS-Diluter PRO IN 4 Spare IN 8 Sliding valve fe...
-
Page 16: Commissioning
: refer to the HMI for the cause of the warning 12. Indication: the white LED on the Panel is blinking 14. Ramp down time: 60 seconds 13. All nozzles 100% open 15. The system continues to run 0000117016/010520/0 SCS-Diluter PRO... -
Page 17: Maintenance
18. You cannot activate this button during the first 40 running hours of the system and within 40 running hours after filter replacement, to maintain the protective 16. The system stops running layer of precoat material on the filter cartridges 0000117016/010520/0 SCS-Diluter PRO... -
Page 18: Troubleshooting
• Disconnect the dustbin by loosening the clip. • Empty the dustbin. • Place the empty dustbin and fasten the clip. • Dispose of the contents of the dustbin in accordance with state or local regulations. 0000117016/010520/0 SCS-Diluter PRO... - Page 19 Filter cleaning buzzer stops USB stick is Firmware USB-stick does Use a USB 2.0 or For more troubleshooting refer to the HMI. update not not comply with USB 3.0 stick recognized possible USB 2.0 standard (too slow) 0000117016/010520/0 SCS-Diluter PRO...
-
Page 20: Spare Parts
We, Plymovent Manufacturing B.V., Koraalstraat 9, 1812 RK Alkmaar, the Netherlands, herewith declare, on our own responsibility, that the product: - SCS-Diluter PRO (incl. Panel and HMI) which this declaration refers to, is in accordance with the conditions of the following:... - Page 21 ANNEX Fig. I Dimensions SCS-Diluter inch 1200 47.2 1200 47.2 2440 96.1 1100 43.3 5425 213.6 3385 133.3 2340 92.1 1810 71.3 1350 53.2 1100 43.3 31.7 Fig. II Dimensions Panel inch 23.6 11.8 31.5 0000117016/010520/0 SCS-Diluter PRO...
- Page 22 ANNEX Fig. III Air circulation Welding fume is mixed at source, so optimum dilution Concentration of welding fume instead of dilution Example: position of two systems Dilution/filtration of a specific section of the facility 0000117016/010520/0 SCS-Diluter PRO...
- Page 23 ANNEX Fig. IV Control panel POWER ON FAN RUNNING WARNING ALARM BEDRIJFSGEREED VENTILATOR DRAAIT WAARSCHUWING ALARM STROMVERSORGUNG EIN VENTILATOR EIN WARNUNG ALARM SOUS TENSION MARCHE VENTILATEUR ATTENTION ALARME ENCENDIDO VENTILADOR EN FUNCIONAMIENTO ATENCIÓN ALARMA 0000112513/A 0000117016/010520/0 SCS-Diluter PRO...
- Page 24 Intermediate ring 0720206050 Flange for dustbin DB-100 Junction box 0840400030 Bush for dustbin DB-100 0046020020 Pressure switch 9820310120 Air inlet module 0046020050 Pressure reducing valve with oil/water 9824000080 Closing valve for dustbin DB-100 separator 9824000090 Piston mechanism 0000117016/010520/0 SCS-Diluter PRO...
- Page 25 0000113559 PCB main board ControlPro 0324000300 Indicator light white 24V 0324000310 Indicator light green 24V 0324000320 Indicator light red 24V 0360000060 Buzzer Fig. VII 0000112777 0000113560 Art. no. Description 0000112777 ControlPro/HMI (complete) 0000113560 Dust cap for ControlPro/HMI 0000117016/010520/0 SCS-Diluter PRO...
- Page 26 NR + 2 α tussen 0° en 25° NR + 0 0,018 0,038 0,0048 0,0083 0,0139 α tussen 25° en 30° NR + 2 NL 7 Technische wijzigingen voorbehouden © 4-2008 NL 7 030 Technische wijzigingen voorbehouden © 4-2008 0000117016/010520/0 SCS-Diluter PRO...
- Page 27 IN 8 Sliding valve 2 closed open IN 9 Fan alarm alarm normal IN 10 Compressed air switch normal alert IN 11 External alarm signal normal alert IN 12 Dustbin level switch full not full 0000117016/010520/0 SCS-Diluter PRO...
- Page 28 0000117016/010520/0 SCS-Diluter PRO www.plymovent.com...
Need help?
Do you have a question about the SCS-DILUTER PRO and is the answer not in the manual?
Questions and answers