Download Print this page

Canon L Series Installing Manual

For direct scanning & copying

Advertisement

Quick Links

Canon
Items Needed at the Installation Site:
Standard Tool Kit
imagePROGRAF iPF670 or iPF770 Service Manual (for
printer installation)
Please Note: Install the imagePROGRAF printer first and verify proper printer operation using roll media before proceeding to install the scanner.
Scanner Unboxing & Initial Preparation:
1. Unbox the scanner, locate the following items in the scanner's box and put each item aside for now:
Scanner Power Supply
Calibration/Stitch Target/sheet
2. Attach both Scanner Mounting brackets on the imagePROGRAF printer by:
3.1. Removing the 4 printer covers shown below
3.2. Fit and mount both left and right brackets as shown below using the supplied screws. The screw locations are shown with 3 small red arrows.
3.3. Replace both left and right lower covers only, as shown with 1 large, dark blue arrow.
Left Side bracket
Installing the L Series Scanner for Direct Scanning & Copying
L Series Scanners L24 & L36 Service Manual (available from the Colortrac
Support Website)
http://www.lseries.colortrac.com
Blank USB2 Flash drive, preformatted FAT 32; must be able to store at least
25Mb of data. This Flash drive can be used to update the scanner firmware.
Ethernet cable
2 Scanner Mounting brackets and 2 Thumb screws
User name:
canon
Password:
scann1ng (note the 'i' is a number 1)
Page 1 of 14
Document Return Guides:
L24 model has 1 guide
L36 model has 3 guides
Right Side Bracket

Advertisement

loading

Summary of Contents for Canon L Series

  • Page 1 Canon Installing the L Series Scanner for Direct Scanning & Copying Items Needed at the Installation Site: Standard Tool Kit L Series Scanners L24 & L36 Service Manual (available from the Colortrac Support Website) http://www.lseries.colortrac.com  User name: canon ...
  • Page 2 3. Carefully lift and place the scanner onto the scanner mounting brackets as shown below. Place the scanner's feet in the holes on the top mounting brackets, and secure the feet with the screws provided Scanner mounting bracket hole Thumb screw Page 2 of 14...
  • Page 3 Preparing the Scanner for First Use: 5. Plug the scanner’s Power Supply into the rear of the scanner. Then plug the AC plug of the Power Supply into an AC Outlet. 6. Turn Scanner ON Updating the Scanner’s Firmware Version: 7.
  • Page 4 8. Compare the Scanner Firmware to the Latest Scanner Firmware Version by visiting the Colortrac L Series Support website shown below. Colortrac Support Website: www.lseries.colortrac.com User Name> canon (note the ‘i’ is a number 1) Password> scann1ng Compare the Firmware level currently installed in the scanner to the latest offering listed on the Colortrac Support website.
  • Page 5 10.4 Confirm 3 files and 1 folder are on the Flash drive as show below. 11. Install the Firmware by inserting the Flash drive containing the firmware into the front USB port of the scanner. 11.1 Use the following Keypad button sequence to install and update the Firmware Page 5 of 14...
  • Page 6 12. Perform a Scanner Light Level adjustment: 12.1 Extend the Scanner Original Support Guides 12.2 Perform the Light Level adjustment by inserting the Calibration and Stitch Target, black section inserted first; face up, so the Target is taken instantly. If the sheet is not straight, lower the scanner’s platen and remove the Target, then close the platen.
  • Page 7 13. Perform a Scanner Calibration: 13.1 Perform a scanner Calibration by inserting the Calibration and Stitch Target, black section inserted first; face up, so the Target is taken instantly. If the sheet is not straight, lower the scanner’s platen and remove the Target, then close the platen.
  • Page 8 14. Perform a Scanner Auto-stitch Adjustment: 14.1 Perform a scanner Auto-stitch Adjustment by inserting the Calibration and Stitch Target, black section inserted first; face up, so the Target is taken instantly. If the sheet is not straight, lower the scanner’s platen and remove the Target, then close the platen.
  • Page 9 Refer to the imagePROGRAF iPF670 or imagePROGRAF iPF770 Service manual for instructions on how to enter the printer’s Static IP Address. 17. Turn off both the iPF Printer and L Series Scanner to recycle the power. Page 9 of 14...
  • Page 10 17. Confirm proper scanner and printer operation by copying and scanning an original. When confirming proper scanner/printer operation; be sure to print on roll fed media only. Printing on Cut Sheets is not supported. Page 10 of 14...
  • Page 11 Configuring the Scanner to Scan to a Network Folder: Appendix: Network Configurations: Please Note: 1. Any of the network configurations in the following illustrations require a Gigabit (1000 Base-T) only. 2. All network PC workstations IP Address schemes must use a ‘Class C’ (255.255.255.0). 3.
  • Page 12 Appendix: (Continued) Additional Network Configurations: (Continued) L series Scanner or iPF670/770 Printer: Only 1 per subnet – Additional L series scanners or iPF670/770 printers should be on a separate subnet. 192.168.001.XXX 255.255.255.000 Router 192.168.002.XXX 255.255.255.000 Page 12 of 14...
  • Page 13 Appendix: (Continued) Additional Network Configurations: (Continued) L Scan App: Multiple L Scan Apps per subnet are not supported. L series Scanner or iPF670/770 Printer: Multiple L series scanners or iPF670/770 printers per subnet are not supported. Page 13 of 14...
  • Page 14 Appendix: (Continued) Additional Network Configurations: (Continued) L series Scanner or iPF670/770 Printer: Multiple iPF670/770 printers per subnet are not supported. End of this procedure. Page 14 of 14...

This manual is also suitable for:

L24L36