Summary of Contents for Harobot HRB-E0110Q
- Page 1 Harobot Non-contact Forehead Thermometer Instructions/manuals Product model:HRB-E0110Q Please read the instructions carefully before using...
-
Page 2: Table Of Contents
Harobot Contents 1. Safety precautions 2. Principle 3. Scope of application 4. Structure composition 5. Product description 6. Operation instructions 7. Considerations 8. Product system settings 9. Memory function 10. Battery replacement 11. Maintenance 12. Transportation and storage conditions 13. Exception message 14. -
Page 3: Safety Precautions
Harobot In order to use the product safely, please read the instruction manual before use. Please keep it properly after reading, so that you can consult it at any time. [Safety precautions] 1. This product is a precision instrument. Please handle it with care to avoid product failure due to impact and falling. -
Page 4: Operation Instructions
Harobot [Operation instructions] The appearance structure of the product is shown in the following figure: 1—Infrared detector 2—LCD screen 3—Up button 4—Down button 5—Set button 6—Measuring button 7—Battery cover Display icon description Icon definition Icon State description Measurement mode Measurement mode and calibration mode display... -
Page 5: Considerations
Harobot [Considerations] Confirm that the screen is in body temperature mode. Aim the thermometer probe at the middle of the forehead and keep it vertical, with a distance of about 3cm ~ 5cm. Press the measurement key, and after about 1 second, the "tick" will display the measured value, and the test is completed. -
Page 6: Memory Function
Harobot Measurement mode setting: In the power on state, press the "set" key briefly to switch the measurement mode to body temperature and calibration. Temperature unit setting - F1 Press and hold the "set" key for 2 seconds, F1 will be displayed on the screen, the icon of Celsius temperature will flash, press the "-"... -
Page 7: Battery Replacement
Harobot [Battery replacement] When the LCD is displayed , it indicates that the battery is in a low power state. Please push the battery cover to replace the battery. Note: do not install the positive and negative poles of the battery. Please dispose of the replaced battery according to the local regulations. -
Page 8: Exception Message
Check if the Beep setting is off Shut down immediately after Check the battery capacity and reload the battery power on [Product performance] Product model HRB-E0110Q Anthropometric range 32.0℃ ~ 42.5℃ Measurement accuracy Within 33.0℃ ~ 37.0℃，Not more than ±0.2℃ Display resolution 0.1℃... -
Page 9: After-Sale Service
Harobot size 150mmx80mmx45mm weight 153g Measurement Distance 3-15cm [Explanation of figures and symbols used in labels] Note, refer to attached documents Represents type B application part [After-sale service] The service life of this product is 2 years, and 1 year free maintenance service is provided. - Page 10 Harobot 61000-3-3 Table 2 Guidance and Statement on Electromagnetic Anti-interference-Non-life Support Equipment and Systems The equipment shall be used in the specified electromagnetic environment, and the customer or user shall ensure that the equipment is used in the following specified electromagnetic environment...
- Page 11 Harobot Table 3 Electromagnetic immunity guidelines and statements - non life support equipment and systems The equipment shall be used in the specified electromagnetic environment, and the customer or user shall guarantee to use the equipment in the following specified electromagnetic environment...
- Page 12 Harobot measures must be taken, such as relocating the equipment or moving it to other environment. in the frequency range of 150k-80mhz, the field strength should be less than 3V / m. Table 4 Recommended distance between this device and portable / mobile RF communication device This equipment can be used in the electromagnetic environment where RF interference is controlled.
- Page 13 Harobot 【Date of manufacture】See package or label 【Service life】2 years 【Name of manufacturer】 Fujian Harobot Rehabilitation Robot Production Co., Ltd. 【Domicile of the registrant】 12 workshops at No. 1, Tengfei Sixth Road, Datong Town, Changting County, Longyan City, Fujian Province 【Production address】...
- Page 14 Harobot Warranty card User files DATE: NAME ADDRESS code Place of purchase Purchase price Sales unit Product name and Machine specification number Dealer signature User signature Warranty clause 1. In case of performance failure within three months from the date of sale of the goods, the goods themselves and the outer packaging must be intact without scratches, and the same type of goods can be replaced, but not including artificial damage.