Brionvega RADIO.CUBO TS522D+S Manual page 17

4. You can store up to 10 DAB radio stations and 10 FM radio stations (the radio
frequency of the FM station saved by default on all presets is 87.50 MHz).
5. To retrieve one of the 10 stored presets, proceed as follows:
For stored presets 1 to 5 press one of the buttons
6. For stored presets 6 to 10 press ShIFT once (the display of the main unit will show
"SHIFT") and then the button corresponding to the desired preset.
PAIRING, CONNECTION AND OPERATION MODE OF ThE UNIT ThROUGh ThE
BLUETOOTh WIRELESS TEChNOLOGY
The TS522D+S radio can be paired with any Bluetooth device. The pairing may differ from
device to device. Refer to the instruction manual of your Bluetooth device for the correct
pairing with the unit.
1. On the first access to this mode, the unit will go into the "waiting for connection" status,
the LED will flash, and in this condition it will be possible to associate a device that has
already been paired. If the device you want to connect has Bluetooth turned on, it will
automatically connect to the radio.
2. Turn on your Bluetooth device (for example a SmartPhone), enter the Bluetooth setup
menu and scan for available devices. In the list of found devices the label Radio.cubo
will be shown.
3. Connect the device to the TS522D+S unit, the device will show the "Connected" status
and the radio LED will change from flashing to solid (if the pairing was successful).
4. At this point, with the TS522D+S radio it will be possible to wirelessly play the music
stored inside the associated device.
5. While a device is connected via Bluetooth, if you want to pair it with another Bluetooth
device, you must first disconnect it by pressing and holding the PAIR button for about
3 seconds until you hear a "beep" sound, or by disabling the connection established
directly from the Bluetooth menu of the associated device. The unit will switch directly to
pairing mode and, at this point, you can connect another device.
CAUTION:
For mobile phones with Bluetooth 2.0, you will be prompted to enter a password during the
pairing process. Press the following string: 0000 (zerozerozerozero)
1/6 2/7 3/8 4/9 5/10
32
MUSIC PLAYBACK
The device you wish to associate with TS522D+S must support AVRCP (Audio Video
Remote Control Profile) in order to control playback through it. Refer to the user manual of
your device. When the music is playing:
1. Button PLAY/PAUSE
a. Press once to pause playback
b. Press again to resume playback
2. VOL - button (from the main unit, rotate the VOL/STB knob counter-clockwise)
a. Press once to decrease the volume by one step
b. Press and hold to decrease the volume in a consistent manner
3. VOL + button (from the main unit, rotate the VOL/STB knob clockwise)
a. Press once to increase the volume by one step
b. Press and hold to increase the volume in a consistent manner
after reaching the maximum level, the display will show the label VOL MAX)
CAUTION:
listen to music at a moderate volume. Continuous exposure to high volume may damage
your hearing.
CONNECT ThE LAST PAIRED BLUETOOTh ENABLED DEVICE
The following is a quick way to connect TS522D+S to the last paired device.
When the product is in standby mode, press the STANDBY button and enter the BT mode
using the MODE button (if the unit is on, but in a different mode, press the MODE button until
you see BT). Turn on the Bluetooth device to be associated. It will be connected automatically.
The Bluetooth Mode LED will light when the connection is successful. If the product fails to
find the last paired device, it will go into standby mode waiting for connection. In this status,
the previously paired devices may be connected to the unit.
RESETTING ThE UNIT'S MEMORY
The unit can store up to 8 different Bluetooth devices. To clear the memory manually you
must be in the BT mode, in the pairing status (LED flashes quickly), press the PAIR button
twice (with an interval of about one second between presses) until it plays a "beep" sound.
At this point, the LED indicating the status of the Bluetooth switches off, and then it starts to
flash again.
CAUTION:
After erasing all memory, the unit will go immediately into pairing mode and you will need to
follow the pairing and connection procedure of a new Bluetooth device.
Remember to delete the name of the radio also from the device you want to connect it to
again, in order to completely reset the pairing between the two devices.
33