Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for FKG Rooter Universal
Summary of Contents for FKG Rooter Universal
- Page 2 Introduc on device. device and pay close a en on to warnings and notes. No ce The trademarks men oned in this manual are the property of their legally registered companies. The file manufacturers, file system names and the file names referred to in this manual are for iden fica on purposes only and are the property of their respec ve manufacturer or brands.
- Page 3 Fig. A Components and Accessories (CX265-28) (CX265-67) (CX265-63) (CX265-64) (CX265-52) (CX265-17) Ligh ng Device Protec ve Sleeve 16:1 Contra-angle (C4-2M) (CX265-23F) (CX265-65) Fig. B Handpiece and Switch...
- Page 4 Fig. C Contra Angle & File connec on Fig. D Accessory Connec on Install Remove...
- Page 5 Fig. E Apex Locator Mode Fig. F Mul -func on Mode...
- Page 6 Fig. G Charging Fig. H Replace the ba ery...
- Page 9 device device in accordance with the manufacturer’s device device device device device. device damage.
- Page 10 device device allowed. device This device might be adversely affected by the electromagne c radia on produced by electrical scalpels, illumina on devices etc. that are being used nearby. device for treatment.
- Page 11 device damage, or the device. device device instrument...
- Page 12 instrument The Rooter® Universal is an electro-medical device intended to drive mechanical instruments intended for dental root canal treatment (files). In addi on, it is intended to help to determine the working length (apex locator func onality).
- Page 13 Do not expose the device to direct sunlight for an extended period of me. If the device has not been used for some me, make sure it works properly before using it again. Refer to the contra-angle opera on manual for all opera ons regarding the contra-angle.
- Page 14 device, c) Connect ligh ng device Insert the ligh ng device into the motor handpiece and clip the electrode on the file.
- Page 15 • When installing/removing the ligh ng device, do not shake them at will to avoid damaging the plug.
- Page 16 Shaper Finisher XP-endo Treatment 1000 rpm 1.0 Ncm Some preset files have automa c parameters. If such a file has been selected, the speed and torque value will display “auto”. auto 1000 rpm 1.0 Ncm...
- Page 17 File systems libraries The device contains libraries of file systems with preset parameters. file systems library FKG preset User Shaper Finisher XP-endo Treatment Shaper Finisher XP-endo Treatment...
- Page 18 handpiece The ligh ng device will con nue to illuminate while the motor handpiece is running. device Change Motor direc on of rota on Only in User file systems, press to change the motor direc on of rota on.
- Page 19 reduced, the motor handpiece returns to normal forward rota on automa cally. When the load is reduced, Load beyond the the motor is automa cally torque limit value torque limit value restored...
- Page 20 In User Recipro file system, torque cannot be changed. In all FKG file systems, rota on direc on, speed, torque and rota on angle cannot be changed. (fixed se ngs) 1000 rpm 1.5 Ncm 1000 rpm 1.5 Ncm...
- Page 21 User library file systems device file systems (4 memories preset at original default se ngs: 1000rpm FW 1.5Ncm) To change speed and torque refer to 2.4.6 (1 memory preset at original default se ngs: +30 /-150 150rpm) speed and rota on angle. a) Hold down un l the Rota on angle flash.
- Page 22 motor handpiece, the device Fig. E device.
- Page 23 device device may not make device immediately and make sure all...
- Page 24 There is slow beeping sound between bars 6-11. There is fast beeping sound between bars 15-17.
- Page 25 device device...
- Page 27 motor handpiece, the device enters Fig. C, D, F d) Connect contra angle holder/ligh ng device device.
- Page 28 Shaper Finisher XP-endo Treatment 1000 1000 File systems library (Refer to chapter 2.4.3) 1000...
- Page 31 Check that the canal length indicator bars light up between number 0.2 and number 0.5. If the canal length indicator bars does not light up between number 0.2 and number 0.5, an accurate measurement cannot be made. In this case, stop using the device immediately and have it repaired.
- Page 32 1000 Check the device’s func on before use with each pa ent. If all the indicator device...
- Page 33 Fig. G device. Using another Do not use the ba ery charger for any other device than the motor handpiece.
- Page 34 (steady s ll purple) will go out and the Charge LED (purple) will flash and start (pulsa ng purple) goes out and the Ready LED (steady s ll purple) will light up. purple...
- Page 35 Fig. H motor handpiece.
- Page 36 Rooter Universal Software version XXX.X again to enter se ng interface.
- Page 37 device that the device is not opera ng properly. Please handpiece,...
- Page 39 Cleaning, disinfec on, and steriliza on have limited impact on the reusable part of the motor handpiece. Therefore, the number of mes the procedure is repeated is determined by the degree of wear of the part. If visual inspec on reveals damaged parts, stop using them and purchase new parts from the manufacturer or dealer.
- Page 40 7.3 Manual Cleaning a) Rinsing the Lip Hook, File Clip and Contra Angle Holder in flowing tap water (<40 ° C) b) A er cleaning, remove any liquid residue with a lint-free co on cloth and then dry with compressed air (1-2 Bar). Do not put the Lip Hook, File Clip, and Contra Angle Holder into the disinfectant container for immersion and disinfec on.
- Page 41 7.5 Automa c Cleaning and Disinfec on It is recommended to use a washer-disinfector to clean and disinfect the Lip Hook, File Clip and Contra Angle Holder. Put the Lip Hook, File Clip and Contra Angle Holder on the tray of the washer- disinfector, select the "surgical instrument", and start the automa c cleaning Cleaning and disinfec on procedure: a) Pre-cleaning: Pre-clean with tap water less than 40 °...
- Page 42 7.6 Drying Manual drying: Removing any liquid residue with a lint-free co on cloth, and then blow dry with compressed air (1-2 Bar). Automa c drying: Refer to chapter 7.5 (f) 7.7 Inspec on and Maintenance A er cleaning and disinfec on, visually inspect the Lip Hook, File Clip and Contra Angle Holder.
- Page 43 Keep the accessories in a dry, dust-free environment a er steriliza on. 7.10 7.10 Storage Store the sterilizing equipment in a dry, clean and dust-free environment at a suitable temperature of 5 ° C to 40 ° C.
- Page 45 150 to 1000rpm min.0.6 Ncm, max.3.5 Ncm...
- Page 46 Authorized representa- DC current (con nuous ve in the European current) community Thermo-Disinfector Autoclave...
- Page 48 instrument can the instrument. This may result in incorrect opera on of the instrument. This instrument has been thoroughly tested and inspected to assure proper perform- ance and opera on! This instrument should not be used adjacent to or stacked with other instrument and this instrument should be observed to...
- Page 53 www. g.ch Wellkang Ltd The Black Church, St. Mary's Place, Dublin 7, D07 P4AX, Ireland Ver 1.0 Revision Date:20200515...