Related Manuals for Garrick BS712
Summary of Contents for Garrick BS712
- Page 1 METAL CUTTING BAND SAW Model BS712 INSTRUCTION MANUAL For your safety, read all instructions carefully. ** This product carries the following approvals. CE, GS, CSA, and CU-L ISO-9001:2008 Certified...
-
Page 2: Safety Rules
SAFETY RULES “Warning! When using electric tools basic safety precaution should always be followed to reduce the risk of fore, electric shock and personal injury, including the following. Read all these instructions before attempting to operate this product and save these instructions.” 1. - Page 3 12. Secure work -Where possible use clamps or a vice to hold the work. It is safer than using your hand. 13. Do not overreach -Keep proper footing and balance at all times. 14. Maintain tools with care -Keep cutting tools sharp and clean for better and safer performance. -Follow instructions for lubricating and changing accessories.
- Page 4 1) The temperature of the environment should range from 5°to 40°. 2) The relative humidity should be within 30%~95%. 3) The altitude should not be higher than 1000M. 4) In transiting and storing condition, the machine should be kept within the temperature between -25°and 55°.
- Page 5 16. Make all adjustments with the power off. Before any maintenance the power plug has to be removed form the supply socket. 17. Disconnect machine from power source when making repairs. Shut off power and clean the blade saw and work area before leaving the machine. Clear away the waste residue so as to avoid accidental injury after working.
-
Page 6: Wiring Diagram
WIRING DIAGRAM Grounding: The grounding of this model is carried out by connecting the yellow/green terminal of supply cable to the grounding terminal of power source. Be sure to ground your machine before connecting machine to power source in any situation. WARNING! Do not disconnect grounding terminal before disconnecting power source. -
Page 7: Specifications
repairs or adjustments! Failure to Specifications comply may cause serious injury! 7” × ★ Cutting Capacity: 7”Round 12”Rectangle Blade speeds: 34-41-59-98MPM50Hz 41-49-69-120MPM60Hz Blade size: 3/4”×0.032×93” Unpacking and clean-up 1. Finish uncrating the saw. Inspect it for shipping damage. If any damage has occurred, contact your distributor. -
Page 8: Prior To Operation
source. first. 2. Remove coolant return hose from tank 10. Keep machine lubricated. cover. “lubrication” section. 3. Slide tank out of saw base and carefully remove lid containing coolant pump. 4. Fill tank to approximately 80% of capacity. 5. Place lid back onto tank and place tank assembly back into base. -
Page 9: Adjusting Blade Guides
Adjusting Blade Guides 1. Disconnect machine from the power source. 2. Loosen knob (1, Fig.6) and knob (2). Slide blade guide assemblies as close as possible material without interfering with the cut. 3. Tighten knob (1) and knob (2) and connect machine to the power source. -
Page 10: Changing Blades
and three quarter to two revolutions 19mm wide by 0.9mm thick by 2360mm clockwise. This equals approximately 800 long. Use of blades with different kgs. of blade tension. specifications cause inferior performance. 1. Disconnect machine from the power source. 2. Raise saw arm to vertical position and lock in place by turning hydraulic cylinder off. -
Page 11: Adjusting Blade Square To Vise
2. Place machinist’s square on table next Adjusting Blade Square to Vise blade as pictured in Fig.11. 3. Check to see blade makes contact with 1. Disconnect machine from the power source. square along the entire width of the blade. 4. -
Page 12: Adjusting Blade Guide Bearings
7. Once tracking is set, tighten bolts (A). valve. 3. Loosen hex cap screw (A, Fig.14) and adjust assembly so that back roller bearing approximately 0.08mm~0.12mm from the back of the blade. 4. Turn nut (B) to adjust eccentric bearing snug to the blade. -
Page 13: Adjusting Bow Weight
WARNING: Make sure power source. disconnected and hands are protected 2. Place saw arm in the horizontal position. before handing blade. Be sure that blade 3. Remove screw (A, Fig.17) from the teeth do not interfere with the roller gearbox and remove cover plate and bearings. -
Page 14: Chip Cleaning Brush
machine oil. when the machine’s power cord has been 5. Keep blade guides clean and free of metal removed from the power source! chips. Failure to comply may cause serious injury! 6. Check guide bearings frequently to make It is important that the blade cleaning brush be sure they are properly adjusted and properly adjusted and kept in good working turning freely. - Page 15 6. Dull blade 4. Increase blade tension a little at a time 7. Speed incorrect 5. Move guides as close to work as 8. Blade guide bearing possible assembly loose 6. Replace blade 9. Blade guide bearing 7. Check manual recommended assembly loose speeds...
- Page 19 NOTES...
- Page 20 Distributed by: Garrick Herbert Pty Ltd KIRRAWEE NSW Australia. www.garrickherbert.com.au...