H3C S3100-52P Operation Manual
Hide thumbs Also See for S3100-52P:

Advertisement

Quick Links

Operation Manual - System Maintenance and Debugging
H3C S3100-52P Ethernet Switch
Chapter 1 Boot ROM and Host Software Loading ..................................................................... 1-1
1.1 Introduction to Loading Approaches .................................................................................. 1-1
1.2 Local Boot ROM and Software Loading ............................................................................ 1-1
1.2.1 BOOT Menu ............................................................................................................ 1-2
1.2.2 Loading by XMODEM Through Console Port ......................................................... 1-3
1.2.3 Loading by TFTP Through Ethernet Port................................................................ 1-8
1.2.4 Loading by FTP Through Ethernet Port ................................................................ 1-10
1.3 Remote Boot ROM and Software Loading ...................................................................... 1-12
1.3.1 Remote Loading Using FTP.................................................................................. 1-12
1.3.2 Remote Loading Using TFTP................................................................................ 1-17
Chapter 2 Basic System Configuration and Debugging ........................................................... 2-1
2.1 Basic System Configuration............................................................................................... 2-1
2.2 Displaying the System Status ............................................................................................ 2-2
2.3 Debugging the System ...................................................................................................... 2-3
2.3.1 Enabling/Disabling System Debugging................................................................... 2-3
2.3.2 Displaying Debugging Status .................................................................................. 2-4
Chapter 3 Network Connectivity Test.......................................................................................... 3-1
3.1 Network Connectivity Test ................................................................................................. 3-1
3.1.1 ping.......................................................................................................................... 3-1
3.1.2 tracert ...................................................................................................................... 3-1
Chapter 4 Device Management .................................................................................................... 4-1
4.1 Introduction to Device Management .................................................................................. 4-1
4.2 Device Management Configuration ................................................................................... 4-1
4.2.1 Device Management Configuration Task list .......................................................... 4-1
4.2.2 Rebooting the Ethernet Switch................................................................................ 4-2
4.2.3 Scheduling a Reboot on the Switch ........................................................................ 4-2
4.2.5 Specifying the APP to be Used at Reboot .............................................................. 4-3
4.2.6 Upgrading the Boot ROM........................................................................................ 4-3
4.2.7 Loading Hot Patch................................................................................................... 4-4
4.2.8 Displaying Pluggable Transceiver Information........................................................ 4-5
4.3 Displaying the Device Management Configuration............................................................ 4-7
4.4 Remote Switch APP Upgrade Configuration Example ...................................................... 4-7

Table of Contents

i
Table of Contents

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the S3100-52P and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for H3C S3100-52P

  • Page 1: Table Of Contents

    Operation Manual – System Maintenance and Debugging H3C S3100-52P Ethernet Switch Table of Contents Table of Contents Chapter 1 Boot ROM and Host Software Loading ..............1-1 1.1 Introduction to Loading Approaches .................. 1-1 1.2 Local Boot ROM and Software Loading ................1-1 1.2.1 BOOT Menu ......................
  • Page 2: Chapter 1 Boot Rom And Host Software Loading

    Operation Manual – System Maintenance and Debugging Chapter 1 Boot ROM and Host Software H3C S3100-52P Ethernet Switch Loading Chapter 1 Boot ROM and Host Software Loading Traditionally, switch software is loaded through a serial port. This approach is slow, time-consuming and cannot be used for remote loading.
  • Page 3: Boot Menu

    Boot ROM loading process. 1.2.1 BOOT Menu Starting..*********************************************************** H3C S3100-52P BOOTROM, Version 101 *********************************************************** Copyright(c) 2004-2007 Hangzhou H3C Technologies Co., Ltd. Creation date : Jul 6 2007, 08:59:35 CPU Clock Speed : 200MHz BUS Clock Speed : 33MHz...
  • Page 4: Loading By Xmodem Through Console Port

    Operation Manual – System Maintenance and Debugging Chapter 1 Boot ROM and Host Software H3C S3100-52P Ethernet Switch Loading Enter the correct Boot ROM password (no password is set by default). The system enters the BOOT Menu: BOOT MENU 1. Download application file to flash 2.
  • Page 5 Operation Manual – System Maintenance and Debugging Chapter 1 Boot ROM and Host Software H3C S3100-52P Ethernet Switch Loading 3. Set XMODEM protocol parameter 0. Return to boot menu Enter your choice(0-3): Step 2: Press 3 in the above menu to download the Boot ROM using XMODEM. The...
  • Page 6 Operation Manual – System Maintenance and Debugging Chapter 1 Boot ROM and Host Software H3C S3100-52P Ethernet Switch Loading Figure 1-1 Properties dialog box Figure 1-2 Console port configuration dialog box...
  • Page 7 Operation Manual – System Maintenance and Debugging Chapter 1 Boot ROM and Host Software H3C S3100-52P Ethernet Switch Loading Step 5: Click the <Disconnect> button to disconnect the HyperTerminal from the switch and then click the <Connect> button to reconnect the HyperTerminal to the switch, as...
  • Page 8 Operation Manual – System Maintenance and Debugging Chapter 1 Boot ROM and Host Software H3C S3100-52P Ethernet Switch Loading Figure 1-5 Sending file page Step 9: After the sending process completes, the system displays the following information: Loading ...CCCCCCCCCC done! Step 10: Reset HyperTerminal’s baudrate to 9600 bps (refer to Step 4 and 5).
  • Page 9: Loading By Tftp Through Ethernet Port

    Operation Manual – System Maintenance and Debugging Chapter 1 Boot ROM and Host Software H3C S3100-52P Ethernet Switch Loading 3. Set XMODEM protocol parameter 0. Return to boot menu Enter your choice(0-3): Step 2: Enter 3 in the above menu to load the host software by using XMODEM.
  • Page 10 Step 2: Run the TFTP server program on the TFTP server, and specify the path of the program to be downloaded. Caution: TFTP server program is not provided with the H3C Series Ethernet Switches. Step 3: Run the HyperTerminal program on the configuration PC. Start the switch. Then enter the BOOT Menu.
  • Page 11: Loading By Ftp Through Ethernet Port

    Operation Manual – System Maintenance and Debugging Chapter 1 Boot ROM and Host Software H3C S3100-52P Ethernet Switch Loading Step 1: Select <1> in BOOT Menu and press <Enter>. The system displays the following information: 1. Set TFTP protocol parameter 2.
  • Page 12 Operation Manual – System Maintenance and Debugging Chapter 1 Boot ROM and Host Software H3C S3100-52P Ethernet Switch Loading Note: You can use one computer as both configuration device and FTP server. Step 2: Run the FTP server program on the FTP server, configure an FTP user name and password, and copy the program file to the specified FTP directory.
  • Page 13: Remote Boot Rom And Software Loading

    Operation Manual – System Maintenance and Debugging Chapter 1 Boot ROM and Host Software H3C S3100-52P Ethernet Switch Loading Enter your choice(0-3): Enter 2 in the above menu to download the host software using FTP. The subsequent steps are the same as those for loading the Boot ROM, except for that the system gives the prompt for host software loading instead of Boot ROM loading.
  • Page 14 Operation Manual – System Maintenance and Debugging Chapter 1 Boot ROM and Host Software H3C S3100-52P Ethernet Switch Loading Password: 230 Logged in successfully [ftp] get switch.btm [ftp] bye Note: When using different FTP server software on PC, different information will be output to the switch.
  • Page 15 Operation Manual – System Maintenance and Debugging Chapter 1 Boot ROM and Host Software H3C S3100-52P Ethernet Switch Loading II. Loading Procedure Using FTP Server As shown in Figure 1-9, the switch is used as the FTP server. You can telnet to the switch, and then execute the FTP commands to upload the Boot ROM switch.btm to the...
  • Page 16 Operation Manual – System Maintenance and Debugging Chapter 1 Boot ROM and Host Software H3C S3100-52P Ethernet Switch Loading Figure 1-10 Command line interface Step 5: Use the cd command on the interface to enter the path that the Boot ROM upgrade file is to be stored.
  • Page 17 Operation Manual – System Maintenance and Debugging Chapter 1 Boot ROM and Host Software H3C S3100-52P Ethernet Switch Loading Figure 1-12 Log on to the FTP server Step 7: Use the put command to upload the file switch.btm to the switch, as shown in Figure 1-13.
  • Page 18: Remote Loading Using Tftp

    Operation Manual – System Maintenance and Debugging Chapter 1 Boot ROM and Host Software H3C S3100-52P Ethernet Switch Loading <Sysname> boot bootrom switch.btm This will update Bootrom on unit 1. Continue? [Y/N] y Upgrading Bootrom, please wait... Upgrade Bootrom succeeded! <Sysname>...
  • Page 19: Chapter 2 Basic System Configuration And Debugging

    Operation Manual – System Maintenance and Debugging Chapter 2 Basic System Configuration H3C S3100-52P Ethernet Switch and Debugging Chapter 2 Basic System Configuration and Debugging When configuring basic system configuration and debugging, go to these sections for information you are interested in:...
  • Page 20: Displaying The System Status

    Operation Manual – System Maintenance and Debugging Chapter 2 Basic System Configuration H3C S3100-52P Ethernet Switch and Debugging To do… Use the command… Remarks Optional Execute this command in user view. When system reaches the specified start time, automatically adds the...
  • Page 21: Debugging The System

    Operation Manual – System Maintenance and Debugging Chapter 2 Basic System Configuration H3C S3100-52P Ethernet Switch and Debugging 2.3 Debugging the System 2.3.1 Enabling/Disabling System Debugging The device provides various debugging functions. For the majority of protocols and features supported, the system provides corresponding debugging information to help users diagnose errors.
  • Page 22: Displaying Debugging Status

    Operation Manual – System Maintenance and Debugging Chapter 2 Basic System Configuration H3C S3100-52P Ethernet Switch and Debugging Perform the following configuration to enable debugging and terminal display for a specific module: To do… Use the command… Remarks Required Enable system debugging...
  • Page 23: Chapter 3 Network Connectivity Test

    Operation Manual – System Maintenance and Debugging H3C S3100-52P Ethernet Switch Chapter 3 Network Connectivity Test Chapter 3 Network Connectivity Test When configuring network connectivity test, go to these sections for information you are interested in: ping tracert 3.1 Network Connectivity Test 3.1.1 ping...
  • Page 24 Operation Manual – System Maintenance and Debugging H3C S3100-52P Ethernet Switch Chapter 3 Network Connectivity Test each ICMP TTL timeout message in order to offer the path that the packet passed through to the destination. To do… Use the command…...
  • Page 25: Chapter 4 Device Management

    Operation Manual – System Maintenance and Debugging H3C S3100-52P Ethernet Switch Chapter 4 Device Management Chapter 4 Device Management When configuring device management, go to these sections for information you are interested in: Introduction to Device Management Device Management Configuration...
  • Page 26: Rebooting The Ethernet Switch

    Operation Manual – System Maintenance and Debugging H3C S3100-52P Ethernet Switch Chapter 4 Device Management 4.2.2 Rebooting the Ethernet Switch You can perform the following operation in user view when the switch is faulty or needs to be rebooted. Note: Before rebooting, the system checks whether there is any configuration change.
  • Page 27: Configuring Real-Time Monitoring Of The Running Status Of The System

    Operation Manual – System Maintenance and Debugging H3C S3100-52P Ethernet Switch Chapter 4 Device Management 4.2.4 Configuring Real-time Monitoring of the Running Status of the System This function enables you to dynamically record the system running status, such as CPU, thus facilitating analysis and solution of the problems of the device.
  • Page 28: Loading Hot Patch

    Operation Manual – System Maintenance and Debugging H3C S3100-52P Ethernet Switch Chapter 4 Device Management To do… Use the command… Remarks Upgrade the Boot ROM boot bootrom { file-url | device-name } Required 4.2.7 Loading Hot Patch A patch is a standalone software unit that is released to fix errors found in a system.
  • Page 29: Displaying Pluggable Transceiver Information

    You are not encouraged to perform any operation on this file. 4.2.8 Displaying Pluggable Transceiver Information At present, three types of pluggable transceivers are commonly used on H3C series Ethernet switches: SFP (Small Form-factor Pluggable): generally used for 100M or 1000M Ethernet interfaces.
  • Page 30 S3100-52P Ethernet Switch Installation Manual. Transceivers customized by H3C refer to the pluggable transceivers with the Vendor Name field being H3C in the prompt information of the display transceiver interface command. Transceivers customized by H3C support display of electrical label information.
  • Page 31: Displaying The Device Management Configuration

    Operation Manual – System Maintenance and Debugging H3C S3100-52P Ethernet Switch Chapter 4 Device Management To do… Use the command… Remarks Display the currently measured value of the display transceiver Available for pluggable digital diagnosis diagnosis interface optical transceivers parameters of the optical...
  • Page 32 Operation Manual – System Maintenance and Debugging H3C S3100-52P Ethernet Switch Chapter 4 Device Management The switch acts as the FTP client, and the remote PC serves as both the configuration PC and the FTP server. Perform the following configuration on the FTP server.
  • Page 33 Operation Manual – System Maintenance and Debugging H3C S3100-52P Ethernet Switch Chapter 4 Device Management Caution: If the Flash memory of the switch is not sufficient, delete the original applications before downloading the new ones. Initiate an FTP connection with the following command in user view. Enter the correct user name and password to log into the FTP server.
  • Page 34 Operation Manual – System Maintenance and Debugging H3C S3100-52P Ethernet Switch Chapter 4 Device Management # Reboot the switch to upgrade the Boot ROM and host software of the switch. <Sysname> reboot Start to check configuration with next startup configuration file, please wait..

Table of Contents