Advertisement
Quick Links
HES K200-622
Cabinet Lock Series
Installation Instructions
Package Contents
Lock Reader
Interface Cable,
System Side
Lock Body
Recommended Tools
Drill, Drill bits: 5/32", 1/2"
Approved Credential:
i.e. iCLASS or Prox ID card
Specifications
Voltage: 12–24 VDC ±10% (Power Supply not provided)
HES K200-622 (Reader) Current Consumption:
12 VDC:
24 VDC:
Operating Temperature: -10C to 50C
Holding Force: 150 lbs
1
Mounting
Template
Machine
screw with
Strike Plate
washer
Double door bracket
Phillips drivers P0, P2
Pencil, Wire Stripper
38 mA peak for Red and Green LED only
226 mA peak for Red and Green LED and Motor Drive
17 mA peak for Red and Green LED only
118 mA peak for Red and Green LED and Motor Drive
Key Override Paddle
2-56x3/8"
6 x 1/2"
0-80x½"
2X
3X
6-32 screws
5/16"
3X
1"
1-1/4"
2X
1-5/8"
1-3/4"
2X
1X
1-7/8"
2X
Interface Cable, Lock Side
Optional:
Cam lock for key override
Part Number 3085006.001, Rev 3
Shaft Extension
2-56x1-1/4"
1X
1X
2-1/2"
2X
2X
Cam
Advertisement
Related Manuals for Assa Abloy Cabinet Lock Series
Summary of Contents for Assa Abloy Cabinet Lock Series
- Page 1 HES K200-622 Cabinet Lock Series Installation Instructions Package Contents Lock Reader Mounting Template Key Override Paddle Shaft Extension 2-56x3/8” 6 x 1/2” 0-80x½” 2-56x1-1/4” Machine screw with 6-32 screws Strike Plate washer Interface Cable, 5/16” System Side 1” 1-1/4” 1-5/8”...
-
Page 2: System Overview
Connector Pin Wiring: Molex 8-Pin Connector Pin Wire Color Description Black 12 VDC Reader (–) White Wiegand Data (1) 12 VDC Reader (+) Green Wiegand Data (0) Blue Red LED Yellow Green LED Molex 4-Pin Connector Pin Violet 12/24 VDC / Lock (COM, –) Pink Tamper / DPS (NC, +) Gray... -
Page 3: Mounting The Lock
MOUNTING THE LOCK NOTE: The HES K200 reader and lock body can be oriented in several ways to accommodate various cabinets and drawers. When selecting an orientation, it should be noted that some reader orientations may prevent use of the key override function. For example, in the door handing shown here, the key override paddle cannot be accessed in orientation “A”, but it can be accessed in orientations “B,”... - Page 4 TRANSFER the location of the inside wall of the cabinet to the door. MEASURE the horizontal distance between the inside edge of the cabinet and the door edge. NOTE: The drawn line depicts the location of the strike mounting surface. LOCATE the lock centerline notch on the latch and MARK this point on the inside of the cabinet door using a pencil.
- Page 5 INSTALL the shaft extension. IF the cabinet door thickness is greater than 1/2” [12.70 mm] (see Table 1), THEN INSTALL the Shaft Extension to the Antenna/Reader as shown below to ensure proper engagement into the lock. Firmly tighten the screw. Table 1 Door Thickness Extension Shaft Used?
- Page 6 INSTALL the Antenna/Reader. CAUTION Pinching the wires may prevent the Reader and Lock from properly functioning. PLACE and HOLD the antenna/reader to the outside of cabinet, routing the wire through the 1/2” [12.70 mm] offset hole, and ENSURE the knob is in the vertical, locked position. NOTE: Use Table 2 to determine the length of the top mount screw needed, based on the thickness of the cabinet door.
- Page 7 CONNECT the antenna/reader wire to the lock body. NOTE: The antenna/reader wire connector is engineered to fit only one way. INSERT the antenna/reader wire connector, ensuring correct orientation TUCK excess cable into the lock body. ATTACH the cover. Connector cable tucked in Part Number 3085006.001, Rev 3...
- Page 8 Attaching the Wiring New 4-/8-Pin Molex Integrated Wiegand: K/KS200 Cabinet Locks, ElectroLynx Wire Color/Function Assignments Connecto 8-Pin Molex Connector 4-Pin Molex Connector Pin/Wire Color Black White Green Blue Yellow Violet Pink Gray 12/24 12/24 12 VDC Wiegand 12 VDC Wiegand Tamper Tamper Function...
- Page 9 NOTE: It is recommended that 10-conductor, 24 AWG, cable be used. ENSURE the following power cabling guidelines are followed: Wire AWG Supply Voltage Allowed Cable Length (ft.)* 20 AWG 6679 22 AWG 4201 24 AWG 2641 * Round trip loss. V = 2 x I x R x xft xft = V / (2 x I x R) POSITION the cable out of the way, as required.
-
Page 10: Fcc Statement
INSTALL for the double-door strike plate mounting bracket. (OPTIONAL) NOTE: The double-door strike plate bracket requires that one door can be inactive or secured. PLACE the bracket on door, making sure it aligns with the mark made in Step 2c and the edge of the door. MARK the door. -
Page 11: Conformité Aux Normes Fcc
CE Statement ASSA ABLOY Electronic Security Hardware hereby declares that these proximity readers are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC (http://ec.europa.eu/enterprise/sectors/rtte/files/guide2009-04- 20_en.pdf). Conformité aux normes FCC Cet appareil est confrome à la Partie 15 des règlements de la FCC. Son fonctionnement est souimes aux deux conditions suivantes: (1) cet appareil ne peut causer d’interférences, et... - Page 12 For Technical Support please call 1-800-626-7590 For information about ASSA ABLOY Electronic Security Hardware cabinet lock solutions, visit assaabloyesh.com Part Number 3085006.001, Rev 3...
Need help?
Do you have a question about the Cabinet Lock Series and is the answer not in the manual?
Questions and answers