Related Manuals for Taewoo cuTex TBC-553L
Summary of Contents for Taewoo cuTex TBC-553L
- Page 2 ENGTH ENGTH ⇒ ⇒ ⇒ C EAR ▷ Set cutting quantity. SPEED Q ‘T Y S E T ☞ ENGTH EXTRA ⇒ ⇒ ⇒ ⇒ C EAR ▷ Press START button. START ☞ E-mail : taewoo@cutex.co.kr http://www.cutex.co.kr - 1 -...
- Page 3 RESET button or power off & on. ← : to correct wrong data. F I E : Function for label cutting (applicable models : TBC-50S, TBC-50SH) E-mail : taewoo@cutex.co.kr http://www.cutex.co.kr - 2 -...
- Page 4 - Do not access hands or any object close to the working knife. (for safety) - When the knife blade becomes dull, please use it after grinding with the grinding machine. (Please do not let the unskilled person grind manually or install the knife blade.) E-mail : taewoo@cutex.co.kr http://www.cutex.co.kr - 3 -...
- Page 5 If you turn it by CW (clock wise) the lower knife will be close to upper knife. And if you turn it by CCW (counter clock wise) the lower knife will move against upper knife. E-mail : taewoo@cutex.co.kr http://www.cutex.co.kr - 4 -...
- Page 6 Please turn it little by little, we recommend about 5 degrees a time. After finishing, please fasten all #B-15, clamping bolts. If you need further information, please contact us at any time. E-mail : taewoo@cutex.co.kr http://www.cutex.co.kr - 5 -...
- Page 7 E-mail : taewoo@cutex.co.kr http://www.cutex.co.kr - 6 -...
- Page 8 ROLLER BEARING HOUSING A-25 A-54 GUIDE SHAFT (LEFT) A-26 TIME BELT A-55 PANEL A-27 TIME GEAR A-56 OP BOARD A-28 ROLLER TANSTION BRACKET A-57 POWER SWITCH A-29 SAFETY COVER SUPPORT A-58 CONTROL BOARD (MB) E-mail : taewoo@cutex.co.kr http://www.cutex.co.kr - 7 -...
- Page 9 E-mail : taewoo@cutex.co.kr http://www.cutex.co.kr - 8 -...
- Page 10 B-33 B-14 CRANK B-34 B-15 CRANK SHAFT B-35 B-16 PRESSURE PLATE B-36 B-17 PRESSURE PLATE B-37 B-18 B-38 B-19 B-39 B-20 B-40 E-mail : taewoo@cutex.co.kr http://www.cutex.co.kr - 9 -...
- Page 11 REEL HANGER E-mail : taewoo@cutex.co.kr http://www.cutex.co.kr - 10 -...
- Page 12 REEL HANGER Part No. Description Part No. Description SHAFT HAND GRIP BOLT ROLL HANGER FRAME SHAFT BASE MATTER SHAFT E-mail : taewoo@cutex.co.kr http://www.cutex.co.kr - 11 -...
-
Page 13: Error Code
After exchange ROM, you should do initialize the controller, due to error message, if you cannot do initialization, please press "SHIFT/ESC' button to escape error message screen and then initialize the controller. E-mail : taewoo@cutex.co.kr http://www.cutex.co.kr - 12 -... - Page 14 Please contact following address for further information. Please do not disassemble / modify machine or its part without any permission. If you disassemble / modify machine or its part, you cannot receive warranty/after-sales service.