Battery Replacement - Elko SOU-2 Manual

Deleting of all programs
Auto
16--sep-- 10
PRG
in starting menu (time is shown
on display) - press simultaneously
button and and display
PRG OK
announces a notice all
Reset
Auto
SOU-2
Performed by shortly pressing the hidden RESET button with a blunt-pointed object (e.g. a pencil
or screw-driver with a diameter of at most 2 mm).
The type of device and software version will be displayed for 1 second, then the device will enter
default mode. This means that the language is set to EN, all data is zeroed (light function, time/
date, user programs, device options function).
An example of SOU-2 programming
Settings for switching upon exceeding the range of 1,500 lux. Settings of hysteresis at 10% and off delay at 10 min. Upon a change of the lux switching range each Friday at 12:00 p.m. to 2,000 and
each Wednesday at 11:00 a.m. to 1,000 lux.
Auto Prog Prog
light intensity
16--sep-- 10
PRG OK
Prog Prog Prog
light time prog add
+ _
OK
Prog Prog Prog
day prog hour minute
OK OK
+ _
Warning
Device is constructed for connection in 1-phase main alternating current voltage 230 V and
must be installed according to norms valid in the state of application. Connection according to
the details in this direction. Installation, connection, setting and servicing should be installed
by qualifi ed electrician staff only, who has learnt these instruction and functions of the device.
This device contains protection against overvoltage peaks and disturbancies in supply. For
correct function of the protection of this device there must be suitable protections of higher
degree (A, B, C) installed in front of them. According to standards elimination of disturbancies
must be ensured. Before installation the main switch must be in position "OFF" and the device
Prog
all
+
OK
OK
press button to complete
OK
the deleting of all set programs
SOU-2
SOU-2
Prog Prog
set (lux) intensity hysteresis
+ _
OK OK
+ _
Prog Prog
prog day prog hour
OK
OK
OK
Prog
Prog
Prog
on
Prog
Prog
OK
Prog
OK
OK
Prog
OK
OK
OK
OK
+ _

Battery replacement

You can change the battery without disassembling the device.
Auto
CAUTION
- only change the battery when the device is disconnected from power supply !!!
- the date and time must be reset after changing the battery !!!
- remove the plug-in module with the battery
- replace the original battery
- enter a new battery so that its upper edge (+) lines up with the plug-in module
- slide the plug-in module in the device and pay attention to polarity (+ up) – for roughly 1 s,
the display will show the name and the software version
- you can connect the device to power supply
Prog Prog Prog
set (%) hysteresis
+ _
OK OK
+ _
Prog Prog
minute
Prog
OK
OK
Prog
+ _
OK
+ _
Prog
on Prog
add
OK OK ESC
Prog
set (lux)
+ _
should be de-energized. Don´t install the device to sources of excessive electro-magnetic in-
terference. By correct installation ensure ideal air circulation so in case of permanent opera-
tion and higher ambient temperature the maximal operating temperature of the device is not
exceeded. For installation and setting use screw-driver cca 2 mm. The device is fully-electronic
- installation should be carried out according to this fact. Non-problematic function depends
also on the way of transportation, storing and handling. In case of any signs of destruction,
deformation, non-function or missing part, don´t install and claim at your seller it is possible to
dismount the device after its lifetime, recycle, or store in protective dump.
7 / 7
Prog Prog
delay
OK OK
+ _
+ _
Prog
on
Prog
Prog
Prog
on Prog
OK
Prog
OK
OK
Prog
set (lux)
OK
OK
OK
+ _
Auto
16--sep-- 10
+
CR2032
Prog Prog Prog
delay
OK OK ESC
Prog
Prog
add prog
OK
OK
OK
- long press (>1s)
- short press (<1s)