Crown CT22015HX-2 Instruction Manual page 25

Symbol
Power tool designation
The power tool has been designed to unscrew and
to tighten threaded fastening elements (bolts, nuts,
screws, bolt screws, etc�)�
Power tool components
1 LED lamp
2 Tool holder
3 Indicators (torque and speed)
4 Button (torque and speed)
5 On / off switch of the LED lamp
6 Battery lock *
7 Control button of the state of battery charge *
8 Indicators of the state of battery charge *
9 Ventilation slots
10 Reverse switch
11 On / off switch
12 Belt clip *
13 Battery *
14 Pin *
15 Spring *
16 Socket wrench *
17 Charger *
18 Carrying bag *
19 Fixing bush
20 Screwdriver bit *
21 Magnetic holder *
22 Charger label *
23 Indicator (red) *
24 Indicator (green) *
* Optional extra
Not all of the accessories illustrated or described
are included as standard delivery.
Installation and regulation of power tool
elements
Before execution of any procedures, centre the
reverse switch 10.
Mounting / dismounting / setting-up of
some elements is the same for all power
tool models, in this case specific models
are not indicated in the illustration.
Meaning
Useful information�
Stepless speed control�
Do not dispose of the power
tool in a domestic waste
container�
Mounting / replacement of accessories (see
fig. 1-2)
[CT22015HX-2, CT22015HX-4]
• While mounting, install the socket wrench 16 on the
tool holder 2 as shown on the figure 1.
• Disassembly operations do in reverse sequence�
[CT22021HX-2, CT22021HX-4]
• Move forward the fixing bush 19 and hold it in this
position (see fig. 2).
• Mount / replace the accessory�
• Release the fixing bush 19�
Screwdriver bit / magnetic holder (see fig. 3)
[CT22021HX-2, CT22021HX-4]
Use accessories that have circular groove at the stem
end, their use will guarantee safe fixation of accessory
in the tool holder 2�
For short screwdriver bits use the magnetic holder 21
for their reliable fixing (see fig. 3).
A magnetic holder 21 is not needed for extended screw-
driver bits 20 (specially purposed for screwdrivers)�
Charging procedure of the power tool
battery
Initial operating of the power tool
The power tool is supplied with a partially charged
battery 13. Before the first use, the battery 13 must
be fully charged.
Charging process (see fig. 4-6)
• Centre the reverse switch 10�
• Press the battery lock 6 and remove the battery 13
(see fig. 4.1, 5.1-5.2).
• Connect the charger 17 to the power supply�
• Insert battery 13 into charger 17 (see fig. 4.2, 6.1).
• Disconnect the charger 17 from power supply after
charging�
• Remove the battery 13 from the charger 17 and
mount battery 13 in the power tool (see fig. 4.3, 6.2).
Charger indicators (see fig. 7)
Charger indicators 23 and 24 inform of the battery 13
charging process� Signals of the indicators 23 and 24
are shown on the label 22 (see fig. 7).
• Fig� 7�1 - (the green indicator 24 is on, the
battery 13 is not inserted in the charger 17) - the
charger 17 is connected to the power network (ready
for charging)�
• Fig� 7�2 - (the green indicator 24 is blinking, the
battery 13 is inserted in the charger 17) - the battery 13
is being charged�
• Fig� 7�3 - (the green indicator 24 is on, the
battery 13 is inserted in the charger 17) - the
battery 13 is fully charged�
English
25