Table of Contents
Advertisement
Quick Links
Protective Cabinet
Features
· Clear, protective polycarbonate cover with siren/strobe alarm.
· Design allows visibility at any angle.
· Complete with mounting hardware and gasket.
· Includes wire shelf, backing plate and siren/strobe alarm — MED models
· External mounting tabs or internal drill dimples.
· Cover includes a coated steel internal mounting plate with a baked on white
enamel finish.
· Siren/strobe alarm lens is red. Also available with amber, green, blue or white lens.
· Siren offers 32 user selectable tones.
· Alarm can be set for a piercing 100 dB or 85 dB.
· Independent strobe and siren timing of 15 seconds, 30 seconds, 60 seconds or
continuous.
· Powered by a 9 VDC battery or external 12-30 volts.
· Low battery indicator.
STI-7534, STI-7535 and STI-7535MED
We protect the things that protect you.
- 1 -
®
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for STI STI-7534
Summary of Contents for STI STI-7534
- Page 1 Protective Cabinet STI-7534, STI-7535 and STI-7535MED Features · Clear, protective polycarbonate cover with siren/strobe alarm. · Design allows visibility at any angle. · Complete with mounting hardware and gasket. · Includes wire shelf, backing plate and siren/strobe alarm — MED models ·...
- Page 2 All units are recommended for indoor use. Unit must be tested periodically to verify the life of battery. STI recommends you change the 9 Volt battery twice a year. When purchasing a siren/strobe alarm, you will need to periodically test the connections to make sure audibles function at a sound level to alert staff.
- Page 3 Dimensions FRONT VIEW 6.44 in. (164mm) BOTTOM VIEW FRONT VIEW Specifications Operating Voltage Internal power 9 VDC battery (not included) 6.44 in. Remote power 12-30 VDC (164mm) Operating Temperature 32°F -120° Power Consumption Stand by: 50µA TOP VIEW Siren low volume: 85mA Siren high volume: 90mA Strobe: 25mA Siren Volume...
- Page 4 (2) PROVIDED 9018 ANCHOR #8-10 Installation of Shelf (included with STI-7535AED) (2) PROVIDED 1. Align wire shelf to bottom mounting posts inside the cabinet. 2. Insert (2) #8-32 x ½ in. machine screw, through #8 washer, into mounting post and tighten.
- Page 5 STEP 2 - Electronic Setup Select alarm tone and timing sequence Note: Select-Alert must be on a flat surface and lens must be installed or the tamper switch will trigger the alarm. SIREN ALARM TONES REMOTE POWER IN 12-24 VDC, 125mA ALARM TIMING NORMALLY OP LED QTY 10...
- Page 6 Step 5 - Electronics Assembly Wiring: After mounting circuit board assembly, connect wires. Refer to terminal strip connections (step 6). Lens installation: Slide lip of lens behind circuit board mounting plate. Rotate lens into position. Secure with tamperproof screw and special. Unit will not operate properly if lens cover is not installed.
- Page 7 #10 x 1 1/2 in. screw Plastic anchor W07532 Wire shelf (included with MED models only) 19002 #8-32 x 3/8 in. screw H07503 Thumb lock - STI-7535 models H18050 Key lock STI-7534 models KIT-H18054 CH751 Step 7 - Operation · Turn key switch onto arm.
- Page 8 • www.sti-usa.com Taylor House • 34 Sherwood Road • Bromsgrove Worcestershire • B60 3DR • England • Tel: +44 (0)1527 520 999 Fax: +44 (0)1527 501 999 • info@sti-emea.com • www.sti-emea.com Inst. 7535MED 2018_12 Printed in USA Subject to change without notice.
Need help?
Do you have a question about the STI-7534 and is the answer not in the manual?
Questions and answers