Related Manuals for BRUSTOR B150XL
Summary of Contents for BRUSTOR B150XL
- Page 2 B-150 (XL) Mounting instructions 0. OVERVIEW 0. OVERVIEW 1. PLACING THE SUPPORTS 1. PLACING THE SUPPORTS 1.a Stand Alone 1.a Stand Alone 1. b Wall Fixation 1. b Wall Fixation 2.PLACING THE VERTICAL POLES 2.PLACING THE VERTICAL POLES 3. MOUNTING THE CROSS MEMBERS 3.
- Page 3 V01 - 2018 B-150 (XL) Mounting instructions › Check if all parts are present, and check if the dimensions are as ordered. Single Couple 6-5/8” 3-3/4” 4-3/4” 9-1/8” 4-3/8” Coupling pole Horizontal coupling profile...
- Page 4 B-150 (XL) Mounting instructions V01 - 2018 › Place the supports as indicated on the following drawings. 1/4”. STAND ALONE SINGLE W - 3-1/2” W - 3-1/2” W - 3/8” Pole support Ground Anchor Floorplate 20x20 COUPLE L - 1-3/4” L - 1/4”...
- Page 5 V01 - 2018 B-150 (XL) Mounting instructions WALL FIXATION L - 9-1/2” DETAIL A › Remove the Pole supports from the vertical poles, also remove the premounted screenguides, and the reinforcement (1). › Attach the pole supports or floorplates onto the floor. ›...
- Page 6 B-150 (XL) Mounting instructions V01 - 2018 . MOUNTING THE CROSS MEMBERS SINGLE › In case of wall fixation, first fix the short poles to the cross members. › Don’t fix the top screws yet. › Don’t forget to mount the drains! 2x3 DIN7504K 6.3x50 Drain Drain...
- Page 7 V01 - 2018 B-150 (XL) Mounting instructions . ADJUSTING THE CONSTRUCTION LEVELNESS › Check the top side of the construction with a laser or a level. › If necessary, adjust the construction. › Move the vertical poles upward untill the top side of the contruction is completely level. ›...
- Page 8 B-150 (XL) Mounting instructions V01 - 2018 . LOUVRES PREPARING AND PLACING THE LOUVRES B-150 › Foresee each louvre with a long axis, than hit it with a hammer until the wider part touches the edge of the louvre. › Foresee each louvre with a sideplate. ›...
- Page 9 V01 - 2018 B-150 (XL) Mounting instructions CONNECTING LOUVREMOTOR › Place the last louvreholder on top of the long axles, and move the motor until it is possible to make a connection. › Position the motor cover plate so that it fits the U bracket of the motor. ›...
- Page 10 B-150 (XL) Mounting instructions V01 - 2018 . FIRST LOUVRES › If a rain sensor was ordered, than first slide it into the vertical pole. › Place the fixed louvres against the mainhousing W1 (opening at the bottom) and W2 (opening at the top). ›...
- Page 11 5970 - (n x 160) (LH-RH) 235” - (n x 6-1/4”) (LH-RH) 3-7/8” 1-1/8” 1-1/8” 1-1/8” 1-1/8” 5865 - (n x 160) (MI) 230-7/8” - (n x 6-1/4”) (MI) B150 1-1/8” B150XL 3-7/8” 1-1/8” 3-7/8” 3-7/8” 3-7/8” 6-5/8” 5950-(nx210): 234-1/4”-(nx8-1/4”) 5950-(nx210) 5950-(nx210) 5950-(nx210) 234-1/4”-(nx8-1/4”)
- Page 12 B-150 (XL) Mounting instructions V01 - 2018 . RAIN GUTTERS › Put the rain gutter in the opening of one of the vertical poles and push it through as far as possible. (1) › Attach the rain gutter under the brackets. (2) ›...
- Page 13 V01 - 2018 B-150 (XL) Mounting instructions . DRAIN › Foresee minimum each L-side with one drain. With drain Without drain / wall fixation › Open the hole of 50mm 2” › Open the hole of 32mm 1-1/4” › Press the corner piece against the bottom of the rain gutter ›...
- Page 14 B-150 (XL) Mounting instructions V01 - 2018 Pole without drainage, with water flow › Open the 32mm hole › Place a stopper with water outlet on the end of the gutter (use silicone) › Firmly tighten all bolts › Slide the tube clamp over the PVC pipe (1) and slide the PVC pipe over the stopper with water outlet(2). ›...
- Page 15 V01 - 2018 B-150 (XL) Mounting instructions . FINISHING REINFORCEMENT › Place a reinforcement in every vertical pole. › When a rainsensor will be mounted in the vertical pole, slide the reinforcement 140mm down. › Foresee the top screw in the horizontal cross members. sw10 COVER VERTICAL POLES ›...
- Page 16 B-150 (XL) Mounting instructions V01 - 2018 COUPLE 4x DIN7982 4.2x19 4x DIN7982 4.2x19 Cover 4x DIN7982 4.2x19 COUPLE COUPLE - WALL FIXATION...
-
Page 17: Wire Diagram
V01 - 2018 B-150 (XL) Mounting instructions . WIRE DIAGRAM IMPORTANT: pass the cables at the side of the box, as shown below. do not drill any hole at the top of the box ! 10.a LOUVREMOTOR Motor Red ED Programming button Rain sensor Mains connection 220V... -
Page 18: Led Lights
B-150 (XL) Mounting instructions V01 - 2018 10.b LED LIGHTS › Connect the LED lights as indicated below. LED A (Max 10m) black/blue LED - (max 3/8”) red/brown/white LED - (max 3/8”) 10.c RAIN SENSOR › Connect the sensor as indicated below. Yellow Green White...
Need help?
Do you have a question about the B150XL and is the answer not in the manual?
Questions and answers