Before Starting The Equipment; Operation - EINHELL TC-BD 350 Original Operating Instructions

longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1 Assembling the machine
•
Position the machine base (1).
•
Fasten mounting flange with pillar (2) using
three screws (3) and washers to drill base (1).
•
Push the drill table (4) with drill table clamp
shaft onto the pillar (2) (Fig. 4). Lock the drill
table into the desired position using the clam-
ping screw (5).
•
Place drill head (6) with V-belt cover (7) and
motor (8) onto the drill pillar and fasten using
the screws (20).
•
Screw the three ball-shaped handles (9) onto
the feeder cross handle.
Note: All bare parts are greased in order to pro-
tect them from corrosion. Before mounting the drill
chuck (10) onto the spindle (11), both parts must
be completely degreased using an environmen-
tally friendly solvent. This ensures optimal trans-
mission of power.
5.2 Installing the machine (Fig. 1)
Before you use the drill for the fi rst time it must be
permanently fi xed in position. Use both mounting
holes (12) in the base plate to do this. Ensure that
the equipment is freely accessible for operation,
adjustment and maintenance.
Note: The fi xing screws may only be tightened
to a point where they do not distort or deform the
base plate. Excessive tension can lead to fracture.
5.3 Hinged chip guard (Fig. 4)
Unscrew the three screws (21). Push the transpa-
rent cover (23) into the groove of the red moun-
ting frame (24) and fasten it again with the screws
(21).
The height of the cover (23) is infi nitely adjustable
and can be locked using both thumb screws (22).
The chip guard (13) can be fl ipped upwards to
change drill bits, however ensure that the chip
Anl_SA_TC_BD_350_SPK8.indb 32 Anl_SA_TC_BD_350_SPK8.indb 32
GB
guard (13) is back in its initial position before rest-
arting the equipment.
5.4 Prior to using the machine for the fi rst
time
Ensure that the voltage of the mains supply com-
plies with the specifi cations on the rating plate.
Connect the equipment only to a socket with the
properly installed earthing contact. The drill is
equipped with a no-volt trip that is designed to
protect the operator from an undesired restart fol-
lowing a drop in voltage. Should this happen, the
equipment must be physically restarted.

6. Operation

6.1 General (Fig. 2)
To switch on the equipment, push in the green
On button "I" (18); the drill starts up. To switch off ,
press the red Off button "O" (19); the drill shuts
down. Ensure that you do not overload the equip-
ment.
If the sound of the motor drops in pitch during
operation, it is being overloaded.
Do not overload the equipment to the point where
the motor comes to a standstill.
6.2 Fitting tools to the drill chuck (Fig. 1)
Make sure that the power plug is removed from
the socket-outlet before changing tools. Only cy-
lindrical tools with the stipulated maximum shaft
diameter may be clamped in the drill chuck (10).
Only use a tool that is sharp and free of defects.
Do not use tools whose shaft is damaged or
which are deformed or fl awed in any other way.
Use only accessories and attachments that are
specifi ed in the operating instructions or have
been approved by the manufacturer.
6.3 Using the quick-change drill chuck
Your drill is equipped with a gear-toothed drill
chuck (10). In order to insert a drill bit, fl ip up the
chip guard (13), insert the drill bit, then tighten
down the drill chuck using the supplied chuck key.
Pull out the chuck key. Ensure that the clamped
tool is fi rmly seated.
Danger! Do not leave the chuck key in the clamp
hole. Doing so will cause the chuck key to be ca-
tapulted out, which could cause injury.
6.4 Setting the speed (Fig. 1/6/7)
First switch the equipment off , then pull the power
plug.
- 32 -
20.05.2019 14:27:59 20.05.2019 14:27:59