EINHELL TC-BD 630 Original Operating Instructions
  1. Manuals
  2. Brands
  3. EINHELL Manuals
  4. Drill
  5. TC-BD 630
  6. Original operating instructions

EINHELL TC-BD 630 Original Operating Instructions

Bench drill
Hide thumbs Also See for TC-BD 630:
Table of Contents

Advertisement

Quick Links

Download this manual
GB
Original operating instructions
Bench Drill
7
Art.-Nr.: 42.505.85
Anl_TC_BD_630_EX_PH_SPK7.indb 1
Anl_TC_BD_630_EX_PH_SPK7.indb 1
TC-BD 630
I.-Nr.: 21010
28.10.2020 13:30:46
28.10.2020 13:30:46

Advertisement

Table of Contents
loading

Related Manuals for EINHELL TC-BD 630

Summary of Contents for EINHELL TC-BD 630

  • Page 1 TC-BD 630 Original operating instructions Bench Drill Art.-Nr.: 42.505.85 I.-Nr.: 21010 Anl_TC_BD_630_EX_PH_SPK7.indb 1 Anl_TC_BD_630_EX_PH_SPK7.indb 1 28.10.2020 13:30:46 28.10.2020 13:30:46...
  • Page 2 - 2 - Anl_TC_BD_630_EX_PH_SPK7.indb 2 Anl_TC_BD_630_EX_PH_SPK7.indb 2 28.10.2020 13:30:48 28.10.2020 13:30:48...
  • Page 3 Pos. Pos. Pos. 1300 1400 1500 2200 2450 - 3 - Anl_TC_BD_630_EX_PH_SPK7.indb 3 Anl_TC_BD_630_EX_PH_SPK7.indb 3 28.10.2020 13:30:50 28.10.2020 13:30:50...
  • Page 4 - 4 - Anl_TC_BD_630_EX_PH_SPK7.indb 4 Anl_TC_BD_630_EX_PH_SPK7.indb 4 28.10.2020 13:30:51 28.10.2020 13:30:51...

  • Page 5: Table Of Contents

    Table of contents 1. Safety regulations 2. Layout and items supplied 3. Proper use 4. Technical data 5. Before using the equipment 6. Operation 7. Replacing the power cable 8. Cleaning, maintenance and ordering of spare parts 9. Disposal and recycling - 5 - Anl_TC_BD_630_EX_PH_SPK7.indb 5 Anl_TC_BD_630_EX_PH_SPK7.indb 5...
  • Page 6 Danger! - Read the operating instructions to reduce the risk of injury Caution! Wear ear-muff s. The impact of noise can cause damage to hearing. Caution! Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials.

  • Page 7: Safety Regulations

    Danger! b) Avoid body contact with earthed surfaces When using the equipment, a few safety pre- such as pipes, heating systems, stoves cautions must be observed to avoid injuries and and refrigerators. There is an increased risk damage. Please read the complete operating of suff...
  • Page 8 tool could cause injuries. maintained electric tools. e) Avoid abnormal working postures. Make Keep cutting tools sharp and clean. Ca- sure you stand squarely and keep your refully maintained cutting tools with sharp balance at all times. This will enable you to cutting edges will jam less and are easier to control the power tool better in unexpected control.

  • Page 9: Layout And Items Supplied

    Protection against fi re and explosion Pull out the mains plug There are spark producing components inside Pull out the mains plug when not using the tool, the device. Do not use the device in the vicinity of prior to maintenance, and when changing the drill combustible liquids or gases.

  • Page 10: Proper Use

    • 10. Drill chuck Drill chuck • 11. Spindle Folding chip guard • 12. Mounting holes Vise • 13. Folding chip guard Original operating instructions • 14. Vise Safety instructions 15. Securing screw 16. Screw 17. Clamping screw 3. Proper use 18.

  • Page 11: Before Using The Equipment

    • Wear ear-muff s. Finally, fit the complete bit head to the pillar. The impact of noise can cause damage to hea- Align the head so that it is horizontal to the ring. base plate and fasten it in position with the screws (33).

  • Page 12: Operation

    6. Operation The various spindle speeds can be set by moving the V-belt. Proceed as follows: • Remove the screw (16) in order to open the 6.1 General (Fig. 2) V-belt cover (7). To switch on the equipment, push in the green •...

  • Page 13: Replacing The Power Cable

    6.8 Setting the height of the drill table (Fig. 6.11 Countersinking and center-drilling 1/13) With this table drill, you can also countersink and • Slacken the tightening screw (35). center-drill. Please observe that countersinking • Set the drill table to the desired position with should be performed at the lowest speed, while a the help of the hand crank (27).

  • Page 14: Disposal And Recycling

    using it. • Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. En- sure that no water can seep into the device. 8.2 Maintenance There are no parts inside the equipment which require additional maintenance.
  • Page 15 5. To make a claim under the guarantee, please register the defective device at: www.Einhell-Service.com. Please keep your bill of purchase or other proof of purchase for the new device. Devices that are returned without proof of purchase or without a rating plate shall not be covered by the guarantee, because appropriate identifi...
  • Page 16 EH 10/2020 (01) Anl_TC_BD_630_EX_PH_SPK7.indb 16 Anl_TC_BD_630_EX_PH_SPK7.indb 16 28.10.2020 13:30:53 28.10.2020 13:30:53...

Table of Contents