EINHELL TC-BD 350 Original Operating Instructions page 29

circumstances.
f) Wear suitable work clothes. Do not wear
loose clothing or jewellery. Keep hair, clo-
thes and gloves away from moving parts.
Loose clothing, jewellery or long hair can get
trapped in moving parts.
g) If vacuuming devices and draining de-
vices can be fi tted, make sure that these
are correctly attached and correctly used.
The use of a dust extraction system can redu-
ce the danger posed by dust.
4. Usage and treatment of the electric tool
a) Do not overload the appliance. Use the
correct tool for your work. You will be able
to work better and more safely within the gi-
ven performance boundaries.
b) Do not use an electric tool with a defec-
tive switch. An electric tool that cannot be
switched on or off is dangerous and must be
repaired.
c) Pull the plug out of the socket and/or
remove the battery before making any ad-
justments to the appliance, changing ac-
cessories or put the appliance down. This
safety measure prevents starting the electric
tool unintentionally.
d) Keep unused electric tools out of the
reach of children. Do not allow people
who are not familiar with the appliance or
who have not read these instructions to
use the appliance. Electric tools are dange-
rous if they are used by inexperienced people.
e) Clean your electric tool carefully. Check
whether moving parts are functioning
properly and not jamming, whether parts
are broken or damaged enough that the
functioning of this electric tool is aff ec-
ted. Damaged parts must be repaired be-
fore using the appliance. Many accidents
are caused by badly maintained electric tools.
f) Keep your cutting tools sharp and clean.
Carefully maintained cutting tools with sharp
cutting edges will jam less and are easier to
control.
g) Make sure to use electric tools, accesso-
ries, spare parts, etc. in accordance with
these instructions. Take the conditions
in your work area and the job to perform
into account. Using electric tools for any
purpose other than the one for which they are
intended can lead to dangerous situations.
Anl_SA_TC_BD_350_SPK8.indb 29 Anl_SA_TC_BD_350_SPK8.indb 29
GB
5. Service
a) Have your electric tool repaired only by
trained personnel and/or the authorized
service agent, using only genuine spare
parts. This will ensure that your electric tool
remains safe to use.
Special safety instructions
The pillar drill was designed in such a way so as
to all but eliminate potential hazards when the
machine is properly used. However, there are a
few safety precautions to observe in order to en-
sure that all residual hazards are ruled out.
Ensure proper voltage
The voltage must comply with the specifi cations
on the rating plate.
Use a socket-outlet with earthing contact
The device may only be operated from an outlet
with the properly installed earthing contact.
Extension cable
The cord cross section of an extension cable
must measure at least 1.5 mm2. Always comple-
tely unwind a cable reel prior to use. Check the
cable for defects.
Protection against electrical shock
Keep the device away from moisture. The device
must neither be damp nor be operated in a humid
environment. Prior to every use, check the device
and the mains cable with plug for damage. Avoid
bodily contact with earthed parts e.g. pipes, hot
elements, etc.
Protection against fi re and explosion
There are spark producing components inside
the device. Do not use the device in the vicinity of
combustible liquids or gases. Otherwise there is a
risk of fi re or explosion.
Handle the device with care
Do not use the cable to pull the plug out of the
socket. Protect the cable from heat, oil and sharp
edges. Keep your tools sharp and clean so that
you can work effi ciently and safely. Follow the
maintenance regulations and the instructions for
changing tools.
Wear suitable work clothes and personal pro-
tection equipment
Loose clothing is not suitable, as it can be caught
by moving parts, causing you to become ent-
angled. Wear a hair net if you have long hair. As
a general rule, jewelry should not be worn when
- 29 -
20.05.2019 14:27:59 20.05.2019 14:27:59