Page 1
Parts & Service Spray Star 1750 Model 15-600-B TeeJet Spray Systems SN: 175G318 September 2018 Product Support: Hwy SS & Poplar Ave; Cameron WI 54822 1-800-891-9435 productsupport@smithco.com...
All Smithco machines have a Serial Number and Model Number. Both numbers are needed when ordering parts. The serial number plate on the Spray Star 1750 is located on the left main frame, by front bumper. Re- fer to engine manual for placement of engine serial number.
Page 4
18. Stop engine before making repairs/adjustments or checking/adding oil to the crankcase. 19. Use parts and materials supplied by Smithco only. Do not modify any function or part. 20. Use caution when booms are down as they extend out beyond the center line of the machine.
MAINTENANCE Before servicing or making adjustments to machine, stop engine and remove key from ignition. Use all procedures and parts prescribed by the manufacturer's. Read the en- gine manual before operation. LUBRICATION Use No. 2 General purpose lithium base grease and lubricate every 100 hours.
Page 7
MAINTENANCE ENGINE OIL Change and add oil according to chart below based on air temperature at the time of operation. Do not over- fill. Use a high quality detergent oil classified "For Service SJ or higher" oil. Use no special additives with rec- ommended oils.
MAINTENANCE BATTERY Batteries normally produce explosive gases which can cause personal injury. Do not allow flames, sparks or any ignited object to come near the battery. When charging or working near battery, always shield your eyes and always provide proper ventilation. Battery cable should be disconnected before using “Fast Charge”.
SERVICE CHART Before servicing or making adjustments to the machine, stop engine, set park break, block wheels and remove key from ignition. Follow all procedures and ONLY use parts prescribed by the manufacturer. Read the engine manual before maintenance. The suggested maintenance checklist is not offered as a replacement for the manufacturer’s engine manual but as a supplement.
END USER SERVICE CHART Duplicate this page for routine use. For the week of: Maintenance Check Item Tues. Wed. Thurs. Fri. Sat. Sun. Check the Safety Seat Switch Check Steering Operation Check the fuel level Check the engine oil level. Clean the air filter Clean the engine cooling fins.
Page 11
ADJUSTMENTS WHEEL CREEP "Creep" is when the engine is running and hydrostatic transmission is in neutral, but due to inadequate align- ment, wheels still move. Do the following procedure to stop this motion. 1. Lift up and support machine so rear wheels are off the ground and can turn freely. 2.
FRONT AXLE PARTS LIST REF# PART# DESCRIPTION QUANTITY 80-167 Dust Cap HNAR-100-14 Slotted Jam Nut, 1 - 14 HMB-100-10 Machine Bushing, 1 x 10GA HP-18-150 Cotter Pin, 11-043 Bearing with Races 80-019 Hub (includes all * items) 11-041 Oil Seal HMB-100-10 Machine Bushing, 1 x 10GA 15-696...
SEAT PANEL PARTS LIST REF# PART# DESCRIPTION QUANTITY 15-723 Hood Latch 15-786 Hood Rod HW-38 Flat Washer, HP-18-075 Cotter Pin, 10-211 Hood Rod Mount 14-294 Seat Kit 14-800 Seat Rail Set HSP-1260-340-250 Seat Spacer 15-762 Roll Bar 60-106 Spray Boss Lever 76-198-03 Seat Belt HB-716-14-100...
TURBO-QUAD AGITATOR PARTS LIST REF# PART# DESCRIPTION QUANTITY 16-036 Agitator Jet (Includes one each ", ", and " orifices) 16-173 Reducer, 16-158 Close Nipple, 16-157 Female Pipe Thread Tee, 16-172 Nylon Nipple, NPT x 3...
76-197 EATON GEAR PUMP PARTS LIST REF# PART# DESCRIPTION QUANTITY Body 76-197-01 Front Plate Washer 76-197-06 Cap Screw 76-197-07 Retaining Ring Shaft Seal 33-061-15 Washer O-Ring Backup Gasket Seal Wear Plate 76-197-04 Shaft (comes with Idler Gear) 76-197-02 Back Plate Plug 76-197-08 Seal Kit...
Page 48
1752 PLUMBING DRAWING ® (RADION 8140] 15-818 #75 Fitting Oring 15-817 #50 Fitting Oring If using Simulated Speed with a Radion 8140, one needs to change back to Ground Speed for proper rate control when spraying.
Page 49
1752 PLUMBING PARTS LIST ® (RADION 8140] REF# PART# DESCRIPTION QUANTITY 16-935 Quick Coupler Cap 8896-68 1" Suction Hose x 68" 18-116 Hose Clamp 16-161 Fitting 8897-35 " Discharge Hose x 35" 18-222 Hose Clamp 16-180 Quick Coupler Male 18-372 3-Way Valve 18-372-01 T-Handle...
Page 51
1754 PLUMBING PARTS LIST ® (TEEJET 744) REF# PART# DESCRIPTION QUANTITY 16-935 Quick Coupler Cap 8896-68 1" Suction Hose x 68" 18-116 Hose Clamp 18-040 Hose Clamp 16-161 Fitting 16-825 Hex Bushing 8897-35 " Discharge Hose x 35" 18-116 Hose Clamp 16-180 Quick Coupler Male 18-372...
Page 52
1755 PLUMBING DRAWING ® ® (DYNAJET + AEROS FOR 18' BOOM 9032-125 " Black Hose x 125" - Left 9032-90 " Black Hose x 90" - Center 9032-136 " Black Hose x 136" - Right 18-040 Hose Clamp FOR 20' BOOM 9032-135 "...
Page 53
1755 PLUMBING PARTS LIST ® ® (DYNAJET + AEROS REF# PART# DESCRIPTION QUANTITY 16-935 Quick Coupler Cap 8896-68 1" Suction Hose x 68" 18-116 Hose Clamp 16-161 Fitting 8897-35 " Discharge Hose x 35" 18-222 Hose Clamp 16-180 Quick Coupler Male 18-372 3-Way Valve 18-372-01...
1752 SYSTEM WIRING [RADION 8140] ® If using Simulated Speed with a Radion 8140, one needs to change back to Ground Speed for proper rate control when spraying. REF# PART# DESCRIPTION QUANTITY Antenna 20-687-02 GPS Speed Sensor 20-697-01 Radion 8140 Console 15-886 Ram Mount 10-643...
17-585 18' HD SUPER BOOM PLUMBING REF# PART# DESCRIPTION QUANTITY 18-417 Single Barb 9032-19 Black Hose " x 19" 18-040 Hose Clamp 18-416 Double Barb 33-506 Nozzle body (see nozzle drawing) 18-415 " Hose Barb 9032-2.5 Black Hose " x 2 "...
Page 69
17-585 18' HD SUPER BOOM PLUMBING FOR DYNAJET ® REF# PART# DESCRIPTION QUANTITY 20-675 Single Hose Barb - Right Orientation 20-673 Single Hose Barb 20-674 Single Hose Barb - Left Orientation 9032-19 Black Hose, " x 19" 18-040 Hose Clamp 9032-2.5 Black Hose, "...
Page 71
17-580 20' HD SUPER BOOM PARTS LIST REF# PART# DESCRIPTION QUANTITY 17-531 Left Boom Arm 17-631 V-Boom Nest 17-578 Boom Nest Post 30-214 10" Electric Hydraulic Actuator 30-184 Actuator Mount HN-38-16 Hex Nut, - 16 (adjustment Hex Bolt) HB-38-16-100 Hex Bolt, - 16 x 1 HW-38 Flat Washer,...
17-580 20' HD SUPER BOOM PLUMBING REF# PART# DESCRIPTION QUANTITY 18-417 Single Barb 9032-19 Black Hose " x 19" 18-040 Hose Clamp 18-416 Double Barb 33-506 Nozzle body (see nozzle drawing) 18-415 " Hose Barb 9032-2.5 Black Hose " x 2 "...
Page 75
17-580 20' HD SUPER BOOM PLUMBING FOR DYNAJET ® REF# PART# DESCRIPTION QUANTITY 20-675 Single Hose Barb - Right Orientation 20-673 Single Hose Barb 20-674 Single Hose Barb - Left Orientation 9032-19 Black Hose " x 19" 18-040 Hose Clamp 9032-2.5 Black Hose "...
Page 76
QJS NOZZLE DRAWING REF# PART# DESCRIPTION QUANTITY Nylon Black Nut 303 Stainless Steel Washer 20-673-09 12V Coil Assembly Tube Sub Assembly 302 Stainless Steel Spring Viton Oring Plunger 303 Stainless Steel Cap 20-673-02 E-Chemsaver Solenoid 20-673-04 3/4" Mount Assembly Pan Head Screw 18-417 Single Barb (part of 20-674-P and 20-675-P) 18-416...
QJS BOTTOM MOUNT NOZZLE ASSEMBLY REF# PART# DESCRIPTION QUANTITY 20-673-02 E-Chemsaver® 20-673-04 " Bottom Mount Nozzle Body 3† 18-417 Single Barb 20-676 Turbo TeeJet Tip 20-677 QT White Cap and Washer 6‡ 18-416 Double Hose Barb Quantity is per nozzle body. For 18' booms multiply quantity by 11. Quantity is per nozzle body.
TRIPLE NOZZLE ASSEMBLY DRAWING REF# PART# DESCRIPTION QUANTITY 33-506 Body 33-538 Cap - Gray 33-553 Nozzle -Gray (XR11006-VS) 16-800 Viton Gasket 33-537 Cap - Red 33-552 Nozzle - Red (XR11004-VS) 33-554 Nozzle - White (XR11008-VS) 16-802 Strainer Quantity is per nozzle body. For 20' booms multiply quantity by 12. Quantity is per nozzle body.
HOSE REEL ADJUSTMENTS OPERATIONAL CHECK: 1. Pull hose off drum at least one full revolution. A clicking noise should be heard from locking mechanism. 2. Let the hose retract. 3. Pull the hose off until the first click is heard. Drum should lock when the hose tension is removed. 4.
HOSE REEL PLUMBING REF# PART# DESCRIPTION QUANTITY 15-738 Flanged Ball Valve 15-740 50 Series Clamp 15-736 #50 Elbow Coupling 15-749 Hose Barb INSTALLATION INSTRUCTIONS Some machines are shipped with the flanged ball valve already installed. If your machine has the ball valve on the tee, remove cap from ball valve and skip to step 3.
Page 88
17-505 FOAM MARKER FOR 1750 DRAWING REF# PART# DESCRIPTION QUANTITY HBFL-516-18-075 Flange Hex Bolt, -18 x HNFL-516-18 Flange Whiz-loc Nut, - 18 15-689 Foamer Bottom Brace HBFL-516-18-075 Flange Hex Bolt, -18 x HN-14-20-075 Hex Bolt, -20 x HBFL-14-20 Flange Whiz-loc Nut, 15-755 Mount Plate 14-291-04...
Page 89
INSTALLATION INSTRUCTIONS Safety: Before working on machine stop engine, set park brake, remove key from ignition and block wheels. Disconnect negative (-) battery terminal. 1. Mount the switch box to the panel to the right of the operator's seat. Remove the drill screw on the right hand rear side and mount the Switch Box (Ref.
Page 90
FOAMER NOZZLE MOUNT REF# PART# DESCRIPTION QUANTITY 16-987 Foam Nozzle Mounting Kit 1 per boom 15-507 Foamer Tubing Clear Tubing 15-511 Foam Nozzle Blue Tubing 15-510-01 Nozzle Mounting Rod Boom 16-795 Square Clamp...
Page 91
INSTRUCTIONS 1. Slide hose clamp onto drop tube of foam nozzle and attach restrictor bell. 2. Place splined end of Nozzle mounting rod (Ref 7) into top of foam nozzle (Ref 5). Tighten screw. 3. Slide two foam nozzle mounts (Ref 2) onto the rod. Place square clamps (Ref 9) on foam nozzle mounts and mount the square clamps to the boom (Ref 8).
10-653 FRESH WATER WASH TANK - FRONT MOUNT REF# PART# DESCRIPTION QUANTITY 10-652 Mount Plate HB-516-18-075 Bolt - 18 x HWL-516 Lockwasher HW-516 Washer 10-234 Wash Tank 17-537 Square U-Bolt 16-158 Close Nipple 16-151 Elbow 16-960 Spigot INSTALLATION INSTRUCTIONS 1. Fresh Water Wash Tank mounts on the left side ROPs. 2.
30-006 FRESH WATER TANK - REAR MOUNT REF# PART# DESCRIPTION QUANTITY 10-234 Wash Tank 10-234-01 16-158 Close Nipple 16-151 Elbow 16-960 Spigot HB-516-18-075 Hex Bolt, - 18 x HWL-516 Lock Washer, HW-516 Washer, 1. Fresh Water Wash Tank mounts on the rear of all the machines. 2.
14-515 WATER METER KIT (GALLONS) 15-618 WATER METER KIT (LITERS) REF # PART # DESCRIPTION QUANTITY 14-524 Filler Outlet 14-514 Water Meter (Gallons) 14-527 Water Meter (Liters) 14-525 Filler Inlet 16-962 1"Quick Coupler (already on machine) 16-961 1" Adapter Quick Coupler (already on machine) 16-851 1"...
Page 98
15-619 CHEMICAL CLEAN-LOAD SAFE FILL SYSTEM REF# PART # DESCRIPTION QUANTITY 8897-31 " Discharge Hose x 31" 16-156 90° Hose Barb 18-116 Hose Clamp 8897113 " Discharge Hose x 113" 18-391 Coupling 16-972 Street Elbow 15-620 Clean-load Assembly HBFL-516-18-075 Flange Hex Bolt, - 18 x HNFL-516-18 Flange Whiz-loc Nut,...
Page 99
15-619 CHEMICAL CLEAN-LOAD INSTALLATION INSTRUCTIONS 1. Make sure sprayer tank is empty and flush all chemical residue from sprayer. Always wear protective clothing, goggles and gloves. 2. Remove plug from tee on spray pump (Ref A). 3. Install one of the 90° fittings (Ref 2), should point to the back of the machine. 4.
Page 100
15-620 CHEMICAL CLEAN-LOAD PARTS DRAWING ®...
15-620 CHEMICAL CLEAN-LOAD PARTS LIST ® REF# PART# DESCRIPTION QUANTITY 15-620-21 Tank Screw, #6 x 1” 15-620-02 Tank Lid 15-620-22 ProClean Container Nozzle 15-620-23 ProClean Push Valve Assembly 15-620-19 Tank Rinse 15-620-20 Gasket, 1” FNPT Coupler Thread Nipple ProClean Tank Wash Nozzle Splash Retainer O-ring Breather Nut, Breather...
Page 102
OPERATING INSTRUCTION STARTUP 1. All Clean-load valves must be closed prior to starting: inlet ball valve, knife valve and hopper rinse ball valve. 2. Open lid to check for foreign objects which may hinder performance or contaminate the system. 3. Close and lock lid by turning cover clockwise. 4.
DECAL LIST This is a list of decals located on the Spray Star 1750. Part number, description and location will help in reor- dering decals. B 15-902 Decal, Tank Volume 1750 C 15-903 Decal, Rear Tank Volume D 15-463 Decal, Spray Pump...
Page 105
30 days from discovery of the condition. If you need help locating an Authorized Smithco Distributor, or if you have questions regarding your warranty rights or responsibilities, you may contact us at: Smithco Product Support Department 200 West Poplar Ave.
Page 106
This warranty does not apply to normal “wear and tear” items. Normal “Wear and Tear” includes, but is not limited to, damage to seats due to wear or abrasion, worn painted surfaces, scratched decals or windows, etc. Smithco may require the return of failed parts or components in order to determine the validity of any warranty claim.
Need help?
Do you have a question about the Spray Star 1750 and is the answer not in the manual?
Questions and answers