Advertisement
Hose
There is a risk of freezing in cold regions of the hose, if your machine is installed in a cold
place. When the machine is not in use, remaining water in the hoses and the pump in the
filter should be merged. Water inlet hoses can be drained after disconnecting them from the
tap.
Purification pump filter
The machine has a filter system to maintain a long pump life Tel'nykh by trapping foreign ob-
ects e.g., buttons, fabric fibers, which fall within the pump during the water draining. It is
recommended to clean the filter when it is dirty. For this:
Disconnect the plug of your machine from the mains. The relative Kreuth filter in the bottom
right corner by pressing marked space on the lid.
The risk of scalding: In the drum can be about 15 liters of hot water at a temperature of 90 ° C.
Open the filter carefully.
Before opening the filter drain the water through the drain hose. Disconnect the drain hose.
Prepare a suitable container and open the cover of the hose. After the water has drained,
replace the cap in place. Open the filter by turning and draining the remaining water (max 30
ml) via the filter plug. Clear the foreign objects inside the filter. Upon completion, turn it
clockwise and close. Close the filter cap by pressing on it.
Attention!
If the filter and hose plug does not match, the plug will pass water.
installation
6
1. Remove the safety bolts are used when transporting.
Before operating the washing machine you must remove the transit bars! For this:
1. Loosen the bolts with "C" markings, loosening their corresponding conductive wrench
counterclockwise.
2. Remove the safety bolts are used when transporting.
3. Insert the plastic plugs labeled "P" in otver- stie vehicle mounting, rotating them in the
direction of arrow and pushing.
Pay attention, please! Keep transport za- presses the case when the machine is to be
transported again. Always transport your machine with transportation locks.
2. Leveling the feet
In order to operate your machine without noise and vibration it must
be properly balanced. Four feet of your machine can be adjusted.
First loosen Plastics massive counter bolt. After adjusting the feet for
leveling the machine, tighten the counter bolt.
3. Connecting supplying / draining water
a) a water supply hose
Your machine is connected to water supply by special hoses
supplied with the machine, pull a together. Hose supplied plastic
inserts or plastic bag for eliminating leaks in the attachment points.
These pads should be used with each
side of the connection.
Gaskets on the machine side should be connected to the channel filter.
After connecting the hose, check all connections for leaks. To eliminate any risk of
occurrence address the water leakage keep the taps off when machine is not used.
Your machine will operate efficiently when the minimum pres- sure water faucet will be 1
atmosphere, and a maximum of 10 atmospheres. Practically 1 bar po- giving 8 liters of water
per minute when tap is fully on.
Connect the hose to the machine. Hold hands bolts, without using a wrench.
Do not connect the machine to a hose supplying water to the hot water. If the machine is
connected to a part of Y to two hoses for supplying water and machines with one water inlet
temperature of the water will be more 40˚C, the machine can switch to the protection mode
regime.
b) the water drain hose
water drain hose may be attached to the bath tub, or directly to the drain. The hose should not
be bent. The drain hose must be fixed to the holder so that it does not fall to the ground. The
hose must be placed at a height of between 40 and 100 cm from the ground. The drain hose
may be placed directly into the sewerage insulating drainer.
4. Electrical connection
Connect the power cord to the power supply, the corresponding parameters of the maximum
voltage and the rated current indicated on the rating plate, which is arranged inside the kick
plate. Note! Page 1 - steps to be taken before the pre-operation of the washing machine in a
fully automatic mode and warnings on safety ex- pluatatsii.
Make sure that you have connected to the grounding outlet elektropita- Niya.
Before contacting the service support
7
You operate the machine, but on the panel lights are off.
Check the grounding of the electrical outlet or a blown fuse. Check if the door is closed
anterior NJ correctly.
Water does not enter the machine.
Check if the front door is closed properly. Dnye its plumbing valves are closed or
clogged water intake filters.
Taken water is directly discharged.
Check whether the drain hose under the ukazani- s operating and there is no manual set.
Water flows out of the machine.
Check the water supply and drain hoses. Tighten compound. washer hose can be worn. If
the reason does not wish to set up yav- one of the above problems, the incorrectly closed
pump filter.
From the distribution container for the detergent foam coming out.
Check the suitability of your laundry detergent in an automatic washing machine. Next time,
use less detergent.
The pump does not drain.
Clean the pump filter. Check whether the drain hose is bent If there is a need for cleaning
the filter pump, read the relevant section of the manual.
- 4- RUS
Advertisement
