Advertisement
1
Antenna Receptacle
Connect to the supplied ISO antenna converter plug.
2
Parking Brake Lead (Yello w/Blue)
Connect this lead to the power supply side of the parking
brake switch to transmit the parking brake status signals to
the INA-N333RR.
3
Audio Interrupt In Lead (Pink/Blac k)
Connect this lead to the Audio Interface output of a cellular
phone which pro vides ground shorting w hen a call is
received.
4
Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
5
Dimmer Lead (Orange)
This lead may be connected to the vehicle's instrument
cluster illumination lead. This will enable the vehicle's
dimmer control to dim the backlighting of the unit.
6
Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle's fuse
box or another unused power source which provides (+) 12V
only when the ignition is turned on or in the accessory
position.
7
Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
8
Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
NOTE
This lead should be used only for controlling the vehicle's power
antenna. Do not use this lead to turn on an amplifier or a signal
processor, etc.
9
Batter y Lead (Yello w)
Connect this lead to the positive (+) post of the vehicle's
battery.
10
Fuse Holder (10A)
11
ISO Power Supply Connector
Speed Sensor (Green/White)
12
Connect to VSS (Digital or Analog 0V - 3V)
Improper connection of the speed pulse line may cause
important safety features of the vehicle to fail (such as the
brakes or air bags). Such failures may result in an accident
and loss of life. We strongly recommend that the installation
be perfor m ed by a trained, authorized Alpine dealer.
* If the connectors of the vehicle are not ISO type or they
are ISO type but not equipped with the speed sensor
terminal on the vehicle side ISO connector, use the
supplied speed sensor auxiliary cable to connect to the
speed sensor cable of the vehicle.
To prevent external noise from entering the audio system.
• Locate the unit and route the leads at least 10 cm away from the car harness.
• Keep the battery power leads as far away from other leads as possible.
• Connect the ground lead securely to a bare metal spot (remove any paint, dirt or gr
• If you add an optional noise suppressor, connect it as far away from the unit as possible. Y our Alpine dealer carries various noise
suppressors, contact them for further information.
• Y our Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
INA-N333RS/INA-N333RRS
Remote Control Interf ace Connector
13
To remote control interf ace box.
14
To RDS-TMC Receiv er (Optional)
NOTE
To connect an Alpine RDS-TMC Receiver, consult your Alpine
dealer.
15
GPS Antenna (Included)
Po w er Supply Connector
16
Ai-NET Connector
17
Connect this to the output or input connector of other
product (CD changer , Equalizer , etc .) equipped with
Ai- NET.
18
System Switch
When connecting a processor using Ai-NET , place this
switch in the EQ/DIV position. When no device is
connected, leave the switch in the NORM position.
NOTE
Be sure to turn the power of f to the unit before changing the
switch position.
Front Output RCA Connectors
19
RED is right and WHITE is left.
Rear Output RCA Connectors
20
RED is right and WHITE is left.
-
21
Subwoofer Output RCA Connectors
RED is right and WHITE is left.
22
RCA Extension Cable (Sold Separately)
23
Ai-NET Cable (Included with CD Changer)
24
ISO Connector (Speaker Output)
25
Left Rear (+) Speaker Output Lead (Green)
26
Left Rear (–) Speaker Output Lead (Green/Black)
27
Left Front (+) Speaker Output Lead (White)
28
Left Front (–) Speaker Output Lead (White/Black)
29
Right Front (–) Speaker Output Lead (Gra y/Black)
30
Right Front (+) Speaker Output Lead (Gra y)
Right Rear (–) Speaker Output Lead (Violet/Black)
31
Right Rear (+) Speaker Output Lead (Violet)
32
r
ease if necessary) of the car chassis.
- 6 -
TO CONTENTS
Advertisement
