Ingersoll-Rand IR15BV Operation And Maintenance
Hide thumbs
Also See for IR15BV:
- Maintenance and service manual (70 pages) ,
- Operation and maintenance (56 pages)
Table of Contents
Related Manuals for Ingersoll-Rand IR15BV
Summary of Contents for Ingersoll-Rand IR15BV
- Page 1 OPERATION AND MAINTENANCE IR15BV AND IR15BS SERIAL NO: 00001CZ01M This manual contains important safety information and must be made available to personnel who operate and CPN: 85040251 GB maintain this machine DATE: DECEMBER 2001...
- Page 2 Machine models represented in this manual may be used in various locations world-wide. Machines sold and shipped into European common market countries requires that the machine display the EC Mark and conform to various direc- tives. In such cases, the design specification of this machine has been certified as complying with EC directives. Any modification to any part is absolutely prohibited and would result in the CE certification and marking being rendered invalid.
- Page 3 G. Ingersoll-Rand Engines – The earlier of twen- A. Aftercoolers – The earlier of nine (9) months ty-four (24) months from shipment to or the ac-...
- Page 4 Accessories or equipment furnished by Ingersoll- business of an Ingersoll-Rand distributor authorised Rand, but manufactured by others, including, but not to sell the type of equipment involved or other es- limited to, engines, tires, batteries, engine electrical tablishment authorised by Ingersoll-Rand.
-
Page 5: Placing Tool In Service
NOTICE IR15BV and IR15BS Paving Breakers are designed for the disintegration of low to medium strength materials (e. g. concrete, masonry bituminous asphalt etc). The tool is intended for vertical or inclined downward breaking. Ingersoll – Rand is not responsible for customer modifications of tools for applications on which Ingersoll –... -
Page 6: Warning Label Identification
WARNING LABEL IDENTIFICATION WARNING FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY. WARNING WARNING WARNING Always wear eye protection Always wear hearing Always turn off the air when operating or perfoming protection when operating supply and disconnect the air maintenance on this tool. -
Page 7: Installation
PLACING TOOL IN SERVICE LUBRICATION INSTALLATION Air Supply and Connections Protec Engine Oil Always use clean, dry lubricated air. Dust, corrosive Always use an air line lubricator with these tools. fumes and/or excessive moisture can ruin the motor We recommend the following Lubricator– of an air tool. -
Page 8: Operation
OPERATION Accessory Installation Always blow out the air line before using to clear the line of dirt. WARNING CAUTION Always turn off the air supply and disconnect the air supply hose before installing, remov- Do not operate the tool unless the chisel is against ing or adjusting any accessory on this tool or the work since this will cause premature wear of before performing any maintenance on this... - Page 9 Loctite 601 – do not disassemble unless replace- vers from each other. Remove the handle springs (11) ment is necessary. ASSEMBLY OF THE IR15BV AND IR15BS PAVING BREAKERS Lightly grip the cylinder assembly vertically in a vice ing pinch bolt hole with the cylinder groove.
-
Page 10: General Instructions
ASSEMBLY OF THE IR15BV AND IR15BS PAVING BREAKERS GENERAL INSTRUCTIONS Assemble left and right hand, hand grips (8 and 9), • Before assembly of the breaker, clean all parts trigger (7) together with sleeve (13), lubricate around thoroughly and lubricate surfaces with a thin the pivot area and position the sub assembly along film of recommended oil (see Lubrication). - Page 12 PARTS LIST Ref. Part Name Quantity Ref. Part Name Quantity Cylinder Assembly (22 x82 Nozzle) 85040509 Trigger 85041275 Cylinder Assembly (25x108 Nozzle) 85040525 Spring Pin 85041283 Nozzle 22 hex x 82 85040517 Trigger Pin 85041291 Nozzle 25 hex x 108 85040533 Bar Grip 85040806...
- Page 13 SPECIFICATIONS FOR IR15BV AND IR15BS PAVING BREAKERS Certified Fronthead Overall Overall Working Consumption Vibration Certified Impact Handle Nut Length Width Weight Pressure /min @ 6 Level Lm/s Noise Frequency Torque Nm Torque Model Chuck Size mm (in) mm (in) Kg (lbs)
- Page 15 Ingersoll – Rand Company Ingersoll – Rand Company Ltd Portable Power Division P.O. Box 868 Portable Power Division 501 Sandford Avenue Swan Lane Mocksville, Hindley Green North Carolina 27028 Wigan WN2 4EZ United Kingdom www.portablepower.irco.com...
Need help?
Do you have a question about the IR15BV and is the answer not in the manual?
Questions and answers