Intel pentium m/celeron m/ulv intel celeron m processor embedded engine board compactflash mini pci 8-bit i/o crt/lvds dual lan audio ata/33/66/100 rs-232/485 usb2.0 pci-104 wdt single +5v h/w monitor (84 pages)
Summary of Contents for BOSER Technology BPC-5019
Page 1
BPC-5019 19” High Speed Panel PC with one PCI slot, 180W ATX P/S...
Page 2
Copyright Disclaimers The accuracy of contents in this manual has passed through checking and review before publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is not liable for manufacturer will any infringements of patents or other rights resulting from its use. The...
Page 4
Declaration of Conformity -- CE Mark BOSER Technology hereby acknowledges that compliance testing in accordance with applicable standards of the EU’s EMC Directive, 89/336/EEC, was successfully completed on a sample of the equipment identified below: Equipment Class: Information Technology Equipment...
Page 5
Safety Instructions The safety recommendations outlined in this section are to be read, understood and followed before operating the product. Keep this information in a safe place for future reference. Failure to comply with any of the following safety procedures could result in serious damage. Do not operate product for any purposes other than its intended use This product is intended for indoor use only Do not operate product if power cord is damaged in anyway...
Page 6
Life Expectancy of Constituent Parts This section describes the life expectancy of constituent parts (backlight, power supply, internal cooling fan and touch screen) which make up to BPC-5019. TFT Display Backlight Display brightness decreases over time with use. The expected operating lifetime of the backlight time to reach 50% initial brightness) is 30,000 hours (assuming continuous lit state at 25 degrees C).
The rear of BPC-5019 design with easy assembly when needed. The BPC-5019 has a 19” touch screen that operates under all types of working environment. It comes with a reliable power supply and 3 of 4cm ball bearing cooling fan that enhance system stability.
180W power supply with UL, CE, CSA, TUV approved Variety of operation system can be used in BPC-5019 The BPC-5019 features an all-in-one flat display and keyboard less operation. The BPC-5019 can be use widely such as, Digital signage, Factory...
Page 9
Reset: 1 sec.~255 min. and 1 sec. or 1 min./step External I/O 6 x USB2.0, 6 x COM, VGA, 2 x LAN, PS/2 KB/MS, MIC In, Line In, Line Out, AD Board VGA Rear I/O BPC-5019-Q SBC Model HS-1750 Intel® Core™ Duo T2050 processor (option) BIOS...
Page 10
Ethernet Chipset Dual Marvell 88E8053 10/100/1000 Mbps LAN Provides Wireless LAN module (option) Drive Bay 1 x 2.5” HDD space 1 x Slim CD-ROM space Watchdog Timer Reset: 1 sec.~255 min. and 1 sec. or 1 min./step Expansion Interface 1 x Standard PCI expansion slot External I/O 6 x USB2.0, 4 x COM, PS/2 KB, PS/2 MS, VGA, DVI, 2 x LAN, MIC In, Line In, Line Out, AD Board VGA...
Page 11
Mechanical & Environmental Thermal System 3 x 4cm ball bearing cooling fan Dimensions (LxHxW) 49.0 x 39.0 x 9.82 cm Cut Out Size (LxH) 43.4 x 34.4 cm Operation Temperature 0~+45 degrees C Storage Temperature -20~+70 degrees C FCC/CE Front Panel Protection IP65 compliance Power Supply 100~240V AC in 180W ATX power supply...
Chapter 2 Unpacking Opening the Delivery Package The BPC-5019 is packed with an anti-static bag. The board contains sensitive electrical components that are easily damaged by static (electricity). Do not remove the anti-static wrapping until proper grounding have been taken. Safety instruction has been described the anti-static precautions and procedures in the previous.
Chapter 3 Hardware Installation This chapter illustrates how to install components into the Panel PC system. External interface please refers to system board’s manual. HDD/CD-ROM/PCI Card Installation 1. Remove the HDD drive bay holding bracket. 2. Install the holding bracket with HDD.
Page 16
3. Remove the CD-ROM drive holding bracket. 4. Install the holding bracket with CD-ROM.
Page 17
5. Install the PCI Card holding bracket. 6. Install the PCI Card with chassis. 7. Use two screws install PCI Card with front panel.
Chapter 4 Touch Screen Driver Installation This chapter illustrates the detailed information for touch screen driver installation procedures. The utility disk that came with the delivery package contains an auto-run program that invokes the installation programs for the touch screen driver. The following sections describe the installation procedures of driver based on WIN2000 operating systems.
Page 20
The next screen is “Choose Install Location”, select “Browse” to choose where to install and click on “Install” to begin installation. Once the Install Shield Wizard finishes updating your system, click on Finish to exit the wizard. We recommend you to reboot your computer to enable the functions.
Page 21
4.1.2 Touch Screen Calibrate To adjust the display with touch screen, right click on “PM” in the system tray of WINXP and choose “Control Panel” to execute calibrate. Choose PenMount 6000USB device and click on “Configure” that will display next screen to start calibrate.
Page 22
Click on “Standard Calibration” button and follow the five calibrate points to do the calibration.
Need help?
Do you have a question about the BPC-5019 and is the answer not in the manual?
Questions and answers