Table of Contents
Related Manuals for Clemas & Co TENNANT S7
Summary of Contents for Clemas & Co TENNANT S7
- Page 1 TENNANT S7 PEDESTRIAN SWEEPER OPERATOR MANUAL Clemas & Co. Unit 16 Ashchurch Business Centre, Alexandra Way, Tewkesbury, Gloucestershire, GL20 8NB. Tel: 01684 850777 Fax: 01684 850707 Email: info@clemas.co.uk Web: www.clemas.co.uk...
-
Page 2: Table Of Contents
TABLE OF CONTENTS TECHNICAL DATA AND CHARACTERISTICS ...................... 2 WARNINGS ................................3 SAFETY MEASURES .............................. 3 SAFETY LABELS ..............................4 SERIAL NUMBER LABEL LOCATION ........................5 INTRODUCTION ..............................5 UNPACKING ................................5 PREPARING THE MACHINE ..........................5 Fitting the side brush ........................... 5 Fitting the handle ............................ -
Page 3: Technical Data And Characteristics
TECHNICAL DATA AND CHARACTERISTICS DESCRIPTION Maximum width inches 1245 Maximum length inches Maximum height clearance with handle inches 37,75 Cleaning width with centre brush inches 19,68 Cleaning width with centre brush and side brush inches Weight with battery 266,76 Front debris bin capacity Operating autonomy <3 m²... -
Page 4: Warnings
WARNINGS SAFETY MEASURES This machine is intended for commercial use only. Its intended Do not use the machine: purpose is to collect dirt, dry waste and dust from dry, paved or • • Unless trained and authorised. carpeted surfaces. • Without having read the operator manual carefully. -
Page 5: Safety Labels
SAFETY LABELS WARNING! RISK OF ENTANGLEMENT WARNING! RISK OF ACID BURNS WARNING! RISK OF BURNS MAXIMUM SLOPE OPERATOR MANUAL, INSTRUCTIONS FOR USE READ THE OPERATOR'S MANUAL DIRECT CURRENT SYMBOL CLASS III APPLIANCE. AN APPLIANCE IS IDENTIFIED AS CLASS III WHEN ITS EXPLOSION-PROOF PROTECTION IS BASED ON THE FACT THAT THERE ARE NO VOLTAGES HIGHER THAN THE ULTRA-LOW SAFETY EXTRA-LOW VOLTAGE (SELV). -
Page 6: Serial Number Label Location
SERIAL NUMBER LABEL LOCATION PREPARING THE MACHINE Make sure that the machine is equipped with a rating plate showing Fitting the side brush • Move the brush raising lever (pos. 1 Fig. 3) to the “0” position. • Unscrew the screw on the side brush shaft. case, notify the dealer immediately. -
Page 7: Preparation, Installation And Replacement Of The Battery
Preparation, installation and replacement of the battery 1) Side brush control lever: moving the lever to “I” position, the side brush moves to the working position and starts rotating. To FOR YOUR SAFETY: Wear protective gloves and eye protection stop the brush, return the lever to the “0” position. when handling the battery and battery cables. -
Page 8: Instructions For Correct Operation
INSTRUCTIONS FOR CORRECT OPERATION ROUTINE MAINTENANCE SAFETY WARNINGS: Any repairs must be performed by a start working as a sweeper. To achieve the highest performance from the sweeper at all times, it is recommended to follow some instructions aimed at keeping the machine in the best conditions WARNING: Before carrying out any work on the and minimising the risk of damage. -
Page 9: Battery Maintenance
BATTERY MAINTENANCE BATTERY CHARGER SETTINGS The battery must always be kept clean and dry. Terminals and IMPORTANT: The battery charger supplied is factory-set for Gel/ poles must be kept clean at all times. Liquid battery (lead-acid), AGM batteries. For lead-acid batteries, the dipswitches on the every 10 hours remove the caps and check the electrolyte level;... -
Page 10: Filter Maintenance
FILTER MAINTENANCE REPLACING AND ADJUSTING THE SIDE BRUSH Replacement After lifting the front of the machine, to replace the side brush, brush. Replace it with the new brush and then tighten the screw, rotating brush. complete with washer. Adjustment Turn the front cowling and remove the front bin. The side brush is adjusted by loosening the screws pos. -
Page 11: Replacing And Adjusting The Belt
Adjusting the centre brush. REPLACING THE FLAPS locking nut pos. 1 Fig. 6/D and turn the adjustment knob pos. 2 Fig. 6/D two full turns clockwise to decrease brush pressure. Retighten locking nut. For proper brush adjustment, the bristles should slightly bend increase the brush pressure to maintain optimum sweeping performance. -
Page 12: Replacing And Adjusting The Cables
REPLACING AND ADJUSTING THE CABLES TROUBLESHOOTING TABLE Replacing the drive cable FAULT CAUSE SOLUTION Belt broken Replace To replace the drive cable, proceed as follows: • Remove the top cowling from the machine. Gear motor Contact service • Loosen the dowel on the cable locking pin. The centre brush damaged centre... -
Page 13: Recommended Spare Parts List
RECOMMENDED SPARE PARTS LIST Part No. WEAR PARTS CUVR00005 BEARING, BRUSH, MAIN PMVR00248 BRUSH KIT, SWEEPER, SIDE, STANDARD CUVR86893 BEARING, SIDE BRUSH SPPV00051 BRUSH KIT, SWEEPER, MAIN [COMPLETE] CUVR37344 BEARING, NEEDLE, WHEEL FTDP76065 FILTER, PAPER, MAIN CUVR37341 BEARING, NEEDLE, WHEEL FTDP00004 FILTER KIT, DUST, PRE-FILTER MPVR76042...
Need help?
Do you have a question about the TENNANT S7 and is the answer not in the manual?
Questions and answers