Advertisement
Advertisement
Table of Contents
Related Manuals for SUNON UP 1
Summary of Contents for SUNON UP 1
- Page 1 Assembly Instruction for UP 1 (Electrical Height Adjustable Desk) sunonglobal.com © 2019 Sunon Inc.
- Page 2 Page 1 of 23...
- Page 3 SAFETY INSTRUCTIONS: WARNING Please read all instructions before using this furniture. This height adjustable desk is not recommended to be used by people with reduced capabilities physically and mentally for safety's sake. · Do not use the desk outdoors. · Do not allow use by children or people NOTE: Desk image is for reference only.
- Page 4 These drawings identify the parts included with your Height Adjustable Desk. Some of these parts are considered by regulatory bodies to be critical components. If any parts shown here do not match your order, please contact Sunon at +86-400-8600666 1 Side Bracket...
- Page 5 These drawings identify the parts included with your Height Adjustable Desk. Some of these parts are considered by regulatory bodies to be critical components. If any parts shown here do not match your order, please contact Sunon at +86-400-8600666 1 Modesty Panel...
- Page 6 These drawings identify the parts included with your Height Adjustable Desk. Some of these parts are considered by regulatory bodies to be critical components. If any parts shown here do not match your order, please contact Sunon at +86-400-8600666 ST5x16...
- Page 7 1. Slide the two Assembly Frames left and right respectively, then remove the Control Panel from the Assembly Frame. 2. Take out the 2 central beams. Page 6 of 23...
- Page 8 Install the Assembly Frames on the left Desk Leg and the Assembly Frame for Control Panel on the right Desk Leg. Make sure the screw holes on the Assembly Frames align with the screw holes on the Desk Legs. Page 7 of 23...
- Page 9 Fasten the 8 M6x10 hex screws with M4 Allen Wrench. Note: If screws accidentally fall into the Assembly Frame, incline the Assembly Frame and take out the screws. M4 Allen M6x10 (x8) Wrench (x1) Page 8 of 23...
- Page 10 1. Align the mounting bars on the Side Brackets with the mounting holes on the Assembly Frames, then install the Side Brackets on the Assembly Frames. The screw holes on the Side Brackets should align with the screw holes on the Assembly Frames. 2.
- Page 11 1. Install the Desk Legs on the Desk Foots, the screw holes on the Desk Legs should align with the screw holes on the Desk Foots. 2. Invert the Desk Legs and fasten the 8 M6x14 hex screws into the screw holes on the Desk Foots. M4 Allen M6x14 (x8)
- Page 12 1. Align the installation slots of the two Central Beams with the installation holes on the two Assembly Frames. 2. Connect the two Assembly Frames by installing the two Central Beams into the installation holes of the two Assembly Frames. Page 11 of 23...
- Page 13 1. Put the Desktop Panel upside down on the ground, then put the desk frame on the Desk Panel. 2. Adjust the width of the Desk Legs to properly align the screws holes. 3. Fasten the Desktop Panel with 11 M6x14 hex screws. 4.
- Page 14 1. Connect one end of the two Adapter Cords to the adapter interfaces at both sides of the Control Panel. 2. Connect the other end of the two Adapter Cords to the adapter interface on the top of the two Table Legs respectively.
- Page 15 Install the Control Panel into the cable plug of the Assembly Frame. Make sure the data cable on the Desk Leg is properly connected to the two sides of the Control Panel. Note: If the data cable is not long enough, connect it to the adapter cord of the Control Panel, then connect the Manual Control Panel to the Control Panel.
- Page 16 Install the Cable Box Cap on the Central Beam, then fasten it with 8 M6x10 hex screw. M6x10 M4 Allen (x8) Wrench (x1) Page 15 of 23...
- Page 17 1. Install the screen clamps on the Modesty Panel and make sure the screw holes are properly aligned, then fasten the clamps with 4 M6x10 hex screws. 2. Install the Modesty Panel to the Desktop Panel by the clamps. Make sure the screw holes are properly aligned, then fasten the clamps with 4 ST5x20 self-tapping screws.
- Page 18 1. Install the Coil Tube on the Desktop Panel. Make sure the screw holes on the fix plate of the Coiled Tube align with the screw holes on the Desktop Panel. 2. Fasten the Coiled Tube with 2 ST5x20 self-tapping screws. Coiled Tube (Optional) (x1)
- Page 19 Optional Step: Put the Integrated Socket to an appropriate position on the desktop, and fasten it. Clamp-on Integrated Socket (Optional) (x1) Page 18 of 23...
- Page 20 Done! Page 19 of 23...
- Page 21 Maintenance and Cleaning ● Normal Cleaning Board: Dust regularly with a slightly damp, soft, lint-free cloth. Wipe dry with a dry, soft cloth in the direction of the wood grain. Spills should be immediately wiped up with a damp cloth. Glass: Clean the surface with a soft cloth soaked in lemonade and vinegar, then dry it with napkins, and finally polish it with a piece of old newspaper.
- Page 22 Maintenance and Cleaning Iron Spot: Wipe the iron spot with special iron wool along the direction of the wood grain, then clean it with a clean cotton cloth, and finally polish the surface. Tags: Soak the tags in oil, then wipe it with special steel wool along the direction of the wood grain, and finally polish the surface.
- Page 23 Simple Trouble Removal Trouble Reason Solution The hinge is loose. Screws are loose. Tighten the screw. The door can't be open The furniture is not evenly placed Even the furniture or adjust the smoothly. or the hinge is not well adjusted. hinge and add some lube.
- Page 24 Simple Trouble Removal Trouble Reason Solution Fabric blistering Adhesive failure in the fabric. Smooth the surface with iron. Panel connectors are not Panels fall apart. Strengthen the connector. well-assembled. The movable part of the chair is Not well-fixed or the snap ring Find out the cause and can't not be moved smoothly.
- Page 25 Brunnenstraße 156, 10115 Berlin, Germany sunonglobal.com...
Need help?
Do you have a question about the UP 1 and is the answer not in the manual?
Questions and answers