WATANABE WPMZ-3 Series Quick Instruction Manual page 5

MODEL WPMZ-3-□□□-□□-□□□
1st Layer 2nd Layer
2InputCalc
ExternalCtrl
1. Input
Hold A/B
CompareAL1
CompareAL2
CompareAL3
CompareAL4
2.Output
AnalogOutput
BCD Output
ModbusCom
RS-232C Com
DispSelect
LevelDisp
3.Display
TrendDisp
4.System General
3rd Layer
(setting items)
Initial values
InsDispStep None
Lower:-99999
DispLimit
Upper:+99999
ExtCtrl 1～5 Func None
PatternSelect Pattern in use
DispHoldMode Normal
HoldOffDelay 0.00
HoldMode NormalHold
DevBaseValue 0
AveHoldCount None
PatternSelect Pattern in use
OutputDispValue None
ActCondition Always
CompareMode LevelJudge
Excess
OnConditions
InTheZone
10000
0
0
Threshold 10000
0
10000
1.00
OnDelay None
OffDelay None
OutputMode Normal
OutputLogic Negative
OnBgColors Black
PatternSelect Pattern in use
OutputRange 0-10V
OutputDispValue None
0
OutputScale
10000
PatternSelect Pattern in use
OutputDispValue None
DataSignalLogic Negative
SyncSignalLogic Negative
SlaveAddress 1
Baudrate 19200bps
Parity Even
Protocol Modbus-RTU
Baudrate 19200bps
Parity Even
DataLength 7bit
Stopbit 1bit
Delimiter CR LF
1ch product
Ach, Ach +
MeasureSelect
Comp
Level, Trend
2ch product
LevelSelect
Ach + Bch,
TrendSelect
Level, Trend
PatternSelect Pattern in use
Ach Scale
0
Bch Scale
10000
CalcScale
AL Select AL1-AL4：ON
PatternSelect Pattern in use
Ach Scale
0
Bch Scale
10000
CalcScale
AL Select AL1-AL4：ON
TimeAxis 1s/div
Brightness 5 Bright
PowerOnDelay None
PowerSavingTime None
4th Layer (setting values)
Initial values
None/5steps/10steps
±99999
±99999
None/CompareReset/HoldResetA,B,A&B
/DispHoldA,B,A&B/Peak_HoldA,B,A&B
/BottomHoldA,B,A&B/AmpHoldA,B,A&B
/DevHoldA,B,A&B/AveHoldA,B,A&B
/DigitalZeroA,B,A&B/PatternChange1,2,3
/DispChange/TrendLog/WaveCompA,B/Mu
ltiHoldA,B
Pattern 1/2/3/4/5/6/7/8
Normal/OneShot
0.00～99.99[sec]
NormalHold/AreaHold
±99999
None/2/4/8/16/32/64times
Pattern 1/2/3/4/5/6/7/8
None/Ach/Bch/Calc
Always/ExceptNearZero/OnStable
/ OnStableExceptNearZero/OnHold
LevelJudge/ZoneJudge/DiffJudge
Excess/LessThan
InTheZone/OutsideTheZone
Threshold：±99999
Hysterisis：0～99999
ZoneLowerLimit：±99999
ZoneUpperLimit：±99999
Hysterisis：0～99999
ChangeAmount：±99999
DetectionInterval：0.00～99.99[sec]
None/20ms/50ms/100ms/200ms/500ms
1s/5s/10s/20s
Normal/Latch/OneShot5ms/10ms/20ms
/50ms/0.1s/0.2s/0.5s/1s/2s
Positive/Negative
Black/Red/Yellow/Green
Pattern 1/2/3/4/5/6/7/8
0-10V/±10V/1-5V/0-20mA/4-20mA
None/Ach/Bch/Calc
0%：±99999
100%：±99999
Pattern 1/2/3/4/5/6/7/8
None/Ach/Bch/Calc
Positive/Negative
Positive/Negative
1～31
9600bps/19200bps/38400bps
None/Even/Odd
ModbusRTU/OriginalCommand/OriginalO
utput
9600bps/19200bps/38400bps
None/Even/Odd
7bit/8bit
1bit/2bit
CR / CR LF
Ach/Bch/Calc/Ach+Comp/Bch+Comp
/Calc+Comp/Ach+Bch/Calc+A+B
Ach/Bch/Calc/Ach+Bch
Pattern 1/2/3/4/5/6/7/8
LowerLimit：±99999
UpperLimit：±99999
AL1/AL2/AL3/AL4
Pattern 1/2/3/4/5/6/7/8
LowerLimit：±99999
UpperLimit：±99999
AL1/AL2/AL3/AL4
1s/div,2s/div,5s/div,10s/div,
30s/div,60s/div120s/div
5Bright/4/3/2/1Dark/0 Off
None/2sec/5sec/10sec/20sec/30sec/60sec
None/1/2/5/10/30/60min
5/12
Remarks
Take over setting of [DecPoint].
Select a function which is attached to each
external control terminals.
Select pattern No. to set.
Select a mode of DispHold.
Take over setting of [DecPoint].
Select pattern No. to set.
Select a condition of comparison.
Only LevelJudge.
Only ZoneJudge.
Only LevelJudge.
Only ZoneJudge.
Only DiffJudge
Compare ON/OFF after ActCondition is
kept certain time set here.
Select an output mode.
Select an output logic.
Priority: AL1 > AL2 > AL3 > AL4
Select pattern No. to set.
Select a type of output range.
Select a ch referenced for analog output.
Scaling of analog output.
Set 0% and 100% value.
Select pattern No. to set.
Select a ch referenced for BCD output.
Select an output mode.
Select an output mode.
Set ID of the product.
Select a baudrate.
Select a type of parity bit.
Select a protocol.
Select a baudrate.
Select a type of parity bit.
Enable when Protocol is
OriginalCommand or OriginalOutput.
Enable when Protocol is
OriginalCommand or OriginalOutput.
Enable when Protocol is
OriginalCommand or OriginalOutput.
*Bch and Calc is enable in 2ch product.
*Bch and Calc is enable in 2ch product.
Select pattern No. to set.
Set scale of level screen.
Select pattern No. to set.
Set scale of trend screen.
Set time scale of division time.
Off means that whole of secreen is turned
off.
Set time that until measure after power
on.
Display is dark while power saving.
IM-0881-04